• 191723 Ball Joint Dust Boots
  • 191723 Ball Joint Dust Boots
  • 191723 Ball Joint Dust Boots
  • 191723 Ball Joint Dust Boots

Ball Joint Dust Boots

Manufacturer: Prothane
Part Number: 191723
Rating 8

Options


Black
Red (Accept Special Order)
Price: $4.77

In Stock Ships Immediately


 
Details

Ball Joint Dust Boots - Ford Mustang - Prothane 191723

Pin Opening Diameter Base Opening Diameter Height of Boot Piece Number
19.05mm (0.75 inch) 44.45mm (1.75 inch) 27.94mm (1.1 inch) 60690
Here is our complete list of universal dust boots.
FitmentBall Joint Dust Boots 191723 fits these vehicles:
  • 2 of 60690 - Ball Joint Dust Boot
  • Lifetime Warranty. Prothane guarantees all Prothane Suspension Parts to be free of defects in materials and workmanship (not due to abuse, neglect or misapplication) for the total time the vehicle remains with the original purchaser of the product(s). Should the products fail to meet these conditions, Prothane will replace the product, free of charge. This excludes any and all related labor charges. The product must be shipped to Prothane (postage prepaid) along with a copy of the original receipt."

Prothane Polyurethane Universal Dust Boots

Many of you are finding out that the rubber boot on your ball joint or tie rod has rotted away or has split. These boots are extremely important for the suspension of your vehicle. Fortunately, Prothane makes Universal Dust boots that will fit most vehicles. These dust boots are made of polyurethane and are far more durable than rubber. This will seal your boot to retain the grease in the joint, as well as protecting the joint from dirt, sand, water and snow.

Prothane Dust Boots

Prothane Dust Boots

How-to obtain measurements

In order to select the proper boot, you will first need to grab a few measurements. The best way to do this is with a set of digital calipers. You will need to measure the diameter of the base where the boot will sit, the diameter of the shaft (also called the Pin Opening Diameter) and the height of the boot. Once you have gotten to your tie rod end measure these three spots. Be sure to be as exact as possible and to write down your measurements. If you have any trouble getting these measurements, give our customer service team at DST a call.

It is important to note that you do not want to choose a boot that is bigger than your measurements. You want to choose a boot that is just slightly smaller than the measurements you obtained. The elasticity of the polyurethane will allow the hole to stretch and grip the joint tightly. If you choose a boot that is too large there will be a gap which lets in debris.


Does this boot match your needs?

Now that you have these measurements, you can verify that this is the boot that you need. If you find that your measurements do not match this boot, go to our Universal Dust Boot page to match a part to your measurements.

Prothane Dust Boots
Prothane 191723

Product Reviews for Ball Joint Dust Boots 191723

Prothane 191723



5 out of 5 based on 8 user reviews. Write a Review

Perfect fit thanks for the help. Great parts!
5 out of 5 - excellant
Paulino A Vigolo - . Prothane 191723
The part fit well and seems to have enough elasticity .Time will tell if it lasts longer than the original did which was 2 1/2 years before splitting .
5 out of 5 - fit was very good
donald mattes - . Prothane 191723
Perfect fit thanks for the help. Great parts!
5 out of 5 - excellant
Paulino A Vigolo - . Prothane 191723
Street rod projects are always an adventure. These units were used to replace the perished stock rubber boots. They fit perfectly on both upper and lower Mustang 2 ball joints.
5 out of 5 - Good quality
Lawrence Klusza - . Prothane 191723
Very Well Made. Great fit for what Im using them for. I had used rubber in the past for the same job but the rubber kept splitting. The Urethane has held up
5 out of 5 - Great Quality
Randy Lawson - . Prothane 191723
I used this product for an application other than a dust boot for a tie rod end. I have a Murray tractor and the jack shaft bearings were failing frequently. The bearing itself was exposed to dust, dirt, and moisture. Very harsh environment for an exposed bearing. I used this product to keep the grease clean there by improving bearing life. \n\nGood quality material, boots are still functioning in a much harsher environment than was originally designed for. \n\nThanks\nTom
5 out of 5 - Very good product, exact measurement specification.
Thomas Ryan - . Prothane 191723
The part fit well and seems to have enough elasticity .Time will tell if it lasts longer than the original did which was 2 1/2 years before splitting .
5 out of 5 - fit was very good
donald mattes - . Prothane 191723
The fitment was great on my mustang II front suspension and the Prothane material is much better than stock rubber.
5 out of 5 - Very good product
Rodney Anglin - . Prothane 191723