Ball Joint Dust Boots - Chevrolet Corvette - 9.13127

  • 9.13127 360image 1
  • 9.13127 Ball Joint Dust Boots
  • 9.13127 Ball Joint Dust Boots
  • 9.13127 Ball Joint Dust Boots
  • 9.13127 Ball Joint Dust Boots
  • 9.13127 Ball Joint Dust Boots
  • 9.13127 360image large 1

Ball Joint Dust Boots

Manufacturer: Energy Suspension
Part Number: 9.13127

:(?)
Black
Red

:(?)
Free Lifetime Warranty Upgrade
Price: $9.36

check_box In Stock check_box Ships Immediately


  • 2 - 13010 Dust Boots
  • 2 - 13014 Dust Boots
  • Energy Suspension warrants its products against defects in workmanship and material for 24 months when used on passenger cars and light trucks. Products that have been abused, altered, or incorrectly installed are not covered. Energy Suspension will replace defective products or component parts, if inspection for factory personnel determines the part to be defective. Warranty replacement covers only the product. Labor claims, time loss, or freight charges will not be honored.
Cross Reference from 9.13127 to 191715
Prothane 191715
Polyurethane.
Price: $7.27
Warranty: Lifetime Warranty

question_answer Ask us a Question

FitmentBall Joint Dust Boots 9.13127 fits these vehicles:
Details
Polyurethane Front Ball Joint Dust Boots
Finally, someone has made a replacement ball joint dust boot! No more expenseor cost worries when the boot wears out or is damaged either from installation or from day to day use.

Ball Joint Dust Boots - Chevrolet Corvette - 9.13127

Pin Opening Diameter Base Opening Diameter Height of Boot Piece Number
14.75mm
(0.580 inch)
36.25mm
(1.425 inch)
35.15mm
(1.385 inch)
13010
16.2mm (0.635 inch) 41.0mm (1.615 inch) 28mm (1.1 inch) 13014
Here is our complete list of universal dust boots.
Polyurethane Front Ball Joint Dust Boots
  • Repair torn and worn out ball joint boots without having to buy the entire ball joint just to get the boot.
  • Adds both durability and that custom look attention custom show car builders!
  • Lasts longer, seals better and looks great for show vehicles!
  • Resist damage from rocks, sand, water, road salt, and oils better than many other O.E.M. rubber boots.
  • Made of Energy's HYPER FLEX performance polyurethane for added performance and durability.
Footnotes
  • One Set Will Cover the Left and Right Side

Energy Suspension Polyurethane Universal Dust Boots

Importance of Dust Boots

Many of you are finding out that the rubber boot on your ball joint or tie rod has rotted away or has split. These boots are extremely important for the suspension of your vehicle. Fortunately, Energy Suspension makes Universal Dust boots that will fit most vehicles. These dust boots are made of polyurethane and are far more durable than rubber. This will seal your boot to retain the grease in the joint, as well as protecting the joint from dirt, sand, water, and snow.

Energy Suspension Universal Dust Boots
Energy Suspension Universal Dust Boots

How to get your measurements

In order to select the proper boot, you will first need to grab a few measurements. The best way to do this is with a set of digital calipers. You will need to measure the diameter of the base where the boot will sit, the diameter of the shaft (also called the Pin Opening Diameter) and the height of the boot. Once you have gotten to your tie rod end measure these three spots. Be sure to be as exact as possible and to write down your measurements. If you have any trouble getting these measurements, give our customer service team at DST a call.

It is important to note that you do not want to choose a boot that is bigger than your measurements. You want to choose a boot that is just slightly smaller than the measurements you obtained. The elasticity of the polyurethane will allow the hole to stretch and grip the joint tightly. If you choose a boot that is too large there will be a gap which lets in debris.

Now that you have these measurements, you can verify that this is the boot that you need. If you find that your measurements do not match this boot, go to our Universal Dust Boot page to match a part to your measurements.

Choose your design

Energy Suspension offers an alternative to the traditional round bushing. There is an octagon shaped dust boot available as an option. The octagonal boots have the same specifications and perform the exact thing. They just offer a more unique look.

Energy Suspension Universal Dust Boots
Energy Suspension 9.13127

Product Reviews for Ball Joint Dust Boots - Chevrolet Corvette - 9.13127

5 Star (11)
92%
4 Star (0)
0%
3 Star (1)
8%
2 Star (0)
0%
1 Star (0)
0%
starstarstarstarstar

Energy Suspension 9.13127

5 out of 5 based on 12 user reviews. Write a Review

K
verified_user

starstarstarstarstar" Great product "

The ball joint dust boots fit perfect and is of a stretchable material. Looks like it will last a while.

verified_user Verified Buyer - - . Energy Suspension 9.13127 - 5 out of 5
F
verified_user

starstarstarstarstar

Excellent product - perfect fit.

verified_user Verified Buyer - - . Energy Suspension 9.13127 - 5 out of 5
F
verified_user

starstarstarstarstar

Excellent product - perfect fit.

verified_user Verified Buyer - - . Energy Suspension 9.13127 - 5 out of 5
W
verified_user

starstarstarstarstar" Came on time and fit perfectly. "

Great product

verified_user Verified Buyer - - . Energy Suspension 9.13127 - 5 out of 5

compare_arrows Compare with Similar Parts


This Part
9.13127 compare
$9.36
Prothane
Prothane compare
$7.27
($2.09) cheaper

question_answer Customer Questions and Answers


Question:
Why does it show two sets of boots for energy susp. 9.13127?
Answer:
Part number 9.13127 comes with 2 different types of dust boots 2 of 13010 and 2 of 13014 in the box.

Question:
Will these boots fit on my 97 Ford Explorer?
Answer:
The 9.13127 is not guaranteed to fit for the 97 Ford explorer unfortunately.