| Prothane Suspension Parts offer a lifetime warranty, but a lifetime warranty doesn't mean anything unless you're happy with the parts. We dont want you to take our word for it that they're excellent parts, just read the reviews below to see for yourself. Folks that have spent their hard earned cash on a part are going to let you know if a part lets them down. EVERY review we have for a Prothane Suspension Part can be found below. If you're not convinced that Prothane is the brand for you, we think these reviews might change your mind. When you've had enough convincing,start here to find the Prothane Suspension Parts for your vehicle. | |
 | Front Leaf Spring and Shackle Bushings - Part Number: 11002 Customer: ralph e. byers Rating:  5 out of 5Overall Opinion: They fit fine. |
 | Rear Leaf Spring and Shackle Bushings - Part Number: 11005_rear Customer: guy prichard Rating: 5 out of 5Overall Opinion: Great They fit perfectly, thank you for your help in figuring out what springs I had on my 77 CJ7. |
 | Rear Leaf Spring and Shackle Bushings - Part Number: 11007 Customer: John Palmer Rating: 5 out of 5Overall Opinion: Excellent Top quality product. Easy to install. |
| Rear Leaf Spring and Shackle Bushings - Part Number: 11007 Customer: Charlie Muller Rating: 5 out of 5Overall Opinion: Very nice fit Made well, very nice fit, easy to install. Noticeably better ride. These don't transmit any vibrations at all. |
| Rear Leaf Spring and Shackle Bushings - Part Number: 11007 Customer: Saar Avrahamov Rating:  1 out of 5Overall Opinion: only 2 out of 6 fit my Jeeps (2001 XJ) Only the shackle bushings fit my XJ. The leaf ones didn't fit and I had to change their size in order to insert them (5 mm diameter in one, 9 mm in the other) it's a rubicon express leaf. I didn't like that product. (Editorial Note: These parts are designed for the XJ. The Rubicon Spring you installed is a TJ Spring, so you would need a different set to fit that correctly.) |
| Rear Leaf Spring and Shackle Bushings - Part Number: 11007 Customer: James Nissen Rating: 5 out of 5Overall Opinion: Easy to install! Would definitely buy these again if needed. |
| Rear Leaf Spring and Shackle Bushings - Part Number: 11007 Customer: Peter Campbell Rating: 5 out of 5Overall Opinion: I would rate the kit #11007 (red) 9 out of 10. Hi Graham Prothane makes an excellent product but their weak point is the very vague instructions with their products. I made one phone call to them for this kit and I have used/installed several other kits of theirs. They must know that the majority of their products are being installed in home garages and not in the local dealership. All around a good product. the most troubling part of this install was the removal of existing bushings. PC |
 | Rear Leaf Spring and Shackle Bushings - Part Number: 11008 Customer: Jeff St John Rating: 5 out of 5Overall Opinion: great kit,easy install! Great product, easy install, would recommend to others.... |
 | Rear Leaf Spring Bushings and Heavy Duty Shackles - Part Number: 11011 Customer: Edmund Lafortune Rating: 5 out of 5Overall Opinion: excellant all around Excellent to deal with came quick all the parts were there and right and everything fit like a glove. Really nice quality parts very happy !!!!!!!!!! |
 | Front Leaf Spring and Shackle Bushings - 2 Inch Main Eye - Part Number: 11014 Customer: Andrew Lawrence Rating: 5 out of 5Overall Opinion: five stars Great fitment on my Wagoneer leaf springs I was surprised by the speed of the shipping ordered Sunday got the part Tuesday |
| Front Leaf Spring and Shackle Bushings - 2 Inch Main Eye - Part Number: 11014 Customer: jeremiah oakley Rating: 5 out of 5Overall Opinion: Great parts! Bushings were what I expected - high quality, great fit. Fast shipping and great communication was a plus. |
| Front Leaf Spring and Shackle Bushings - 2 Inch Main Eye - Part Number: 11014 Customer: guy prichard Rating: 5 out of 5Overall Opinion: Great Thank You everything fit perfectly. |
 | Body Mounts Bushings and Radiator Support Bushings - CJ8 - Part Number: 1104 Customer: joe koyshman Rating: 5 out of 5Overall Opinion: Great product Not much to say here, a great product at a great price and the best customer service. |
 | Body to Frame Mount and Radiator Support Bushings - Part Number: 1105 Customer: John S Stanley Rating: 5 out of 5Overall Opinion: The Best It's nice to see great customer service for a change. I got the exact parts I ordered without a surprise situation. Fast delivery. |
 | Body to Frame Mount and Radiator Support Bushings - Part Number: 1107 Customer: Wade J Helzer Rating: 5 out of 5Overall Opinion: installed nice and neat no problems encountered with these parts. installed easy and quickly. great product. |
 | Body Mounts Bushings - Part Number: 1108 Customer: Tyler Merriam Rating: 5 out of 5Overall Opinion: Good Quailty These match the factory really nice and look good. |
 | Front Sway Bar and Endlink Bushings - 15/16 Inch - Part Number: 11101 Customer: Greg Barnes Rating: 5 out of 5Overall Opinion: Very nice product easy to install. Big improvement. The product was very solid and a good choice for replacement. The only problem I had the slots in the sway bar bushing straps were not big enough for the factory bolts on my 1984 CJ7. I reamed the slots out enough to accommodate the bolts and all was done. Thanks for the great price on a great product. |
 | Front Sway Bar and Endlink Bushings - 28mm - Part Number: 11105 Customer: George Jackson Rating: 5 out of 5Overall Opinion: Worked Great Install was great, no problem, buy again. |
 | Front Sway Bar and Endlink Bushings - 1-1/8 Inch - Part Number: 11107 Customer: Robert Wheeler Rating: 5 out of 5Overall Opinion: Very high quality & easy to install I bought these bushings and installation on my Jeep was a breeze. I would purchase again for sure. |
 | Front Sway Bar and Endlink Bushings - 30.5mm - Part Number: 11111 Customer: Derrick Johnson Rating:  3 out of 5Overall Opinion: Product was excellent, description is not The bushings I received were great, but the description said with end-links. I received stabilizer shock bushings and tie rod bushings. I also bought part 11112 which is the rear which came with link bushings but can't seem to find the front sway bar LINK bushings anywhere. What is pictured are not end-links, the hour-glass shaped in rear are steering stabilizer shock bushings, the dome shaped are tie rod bushings, and big ones are sway bar bushings. |
 | Rear Sway Bar and Endlink Bushings - 13mm - Part Number: 11112 Customer: William I Applegate Rating: 5 out of 5Overall Opinion: Excellent product I replaced all the bushings on my 1998 Jeep. These really make a difference. |
| Rear Sway Bar and Endlink Bushings - 13mm - Part Number: 11112 Customer: Russell Goodman Rating: 5 out of 5Overall Opinion: Very satisfied Great product, simple to install, great service, communication and fast shipping. |
 | Front Sway Bar and Endlink Bushings - 1-1/4 Inch - Part Number: 11113 Customer: Paul Moffitt Rating: 5 out of 5Overall Opinion: OK What little grease supplied is not near enough to prevent the squeaking noise for very long. I had to disassemble all the parts, buy and grease them thoroughly and reinstall. The bushings still make noise occasionally. Will probably have to purchase some rubber parts and replace all of them. They perform well, but I think they will not last very long from what wear I have seen so far. You get what you pay for...... |
| Front Sway Bar and Endlink Bushings - 1-1/4 Inch - Part Number: 11113 Customer: Don Jordan Rating: 5 out of 5Overall Opinion: Quick delivery and quality parts I received my parts very quickly and the parts were exactly what I ordered. I will use energy suspension parts again. The only hard part was removing the old bushings from the sway bar end links. |
| Front Sway Bar and Endlink Bushings - 1-1/4 Inch - Part Number: 11113 Customer: David J Chiusano Rating:  2 out of 5Overall Opinion: okay product These replacement parts have rectified the severe squeaking noise in the front sway bar and suspension but not entirely. The rear, which used a greasable fitting for the sway bar bushings still squeaks. Never noticed how much until the front noise level was alleviated somewhat. Guess I'll have to live with it. Sometimes OEM parts are better. |
 | Rear Sway Bar and Endlink Bushings - 9/16 Inch - Part Number: 11114 Customer: John Booker Rating: 5 out of 5Overall Opinion: Good The parts were fine. The only discrepancy was that the brass insert (4 pieces) were of two different lengths, with the longer two being exactly the same length as the factory (OEM) part, whereas the shorter two were about 1/8th inch shorter so that the connecting bolts turn on the ends of the bushing rather than being fully tightened on the insert and turning it inside the bushing. |
| Rear Sway Bar and Endlink Bushings - 9/16 Inch - Part Number: 11114 Customer: Robert J. Audette Rating: 5 out of 5Overall Opinion: Excellent Product Very easy installation and work great! |
| Rear Sway Bar and Endlink Bushings - 9/16 Inch - Part Number: 11114 Customer: Don Jordan Rating: 5 out of 5Overall Opinion: Good fit, easy to install and prompt delivery I replaced the Sway bar bushings on my 2004 Jeep Grand Cherokee after upgrading to a larger diameter rear sway bar. The bushings were easy to install and came with the necessary grease to install; however, it would have been nice to have some sort of instruction as to how much grease to apply and where to apply it. |
| Rear Sway Bar and Endlink Bushings - 9/16 Inch - Part Number: 11114 Customer: Ralph Henry Rating: 5 out of 5Overall Opinion: Great!! I am very happy with this sway bar kit. They are stiffer and that is what I was looking for. The fit was perfect and tighten the sway bar up. The shipping was fast and it was great doing business with Energy Suspension Parts. Thanks Man |
| Rear Sway Bar and Endlink Bushings - 9/16 Inch - Part Number: 11114 Customer: Dmitri Krivihhin Rating:  4 out of 5Overall Opinion: Large bushings suit perfectly, small bushings (4 pc) shattered and under them had put the strips. |
 | Front Sway Bar Bushings - 7/8 Inch - Part Number: 11121 Customer: Lella Elhoffer Rating: 5 out of 5Overall Opinion: excellent Quick service. Parts just as advertised. |
 | Front Sway Bar Bushings - 15/16 Inch - Part Number: 11123 Customer: EDWARD MATUSIK Rating: 5 out of 5Overall Opinion: Great product and service Hard to find part for a classic car, perfect reproduction to replace old style rubber parts. |
 | Front Sway Bar Bushings - 30.5mm - Part Number: 11125 Customer: Francis A McEwan Rating: 5 out of 5Overall Opinion: Excellent Love the red color. Replaced worn OEM parts with superior performance. Now able to easily rotate the sway bar when sway bar disconnects are disconnected. |
 | Rear Sway Bar Bushings - 19mm - Part Number: 11126 Customer: Lance Wetteland Rating: 5 out of 5Overall Opinion: excellent value and performance So very easy to install. Takes about 30 minutes (if you're slow). Dramatic improvement in reducing sway. I have them on all of my vehicles including the motor-home. Surprising what a little cost can do to go a long way. Get these and you won't be disappointed. |
 | Body Lift Kit - 1 Inch - Part Number: 1113 Customer: Jeff A. Nussear Rating: 5 out of 5Overall Opinion: Good quality Good quality parts and hardware. Everything is included in this kit. Installed in about 45 Minutes once I got the old stock junk out. |
 | Body Lift Kit - 1 Inch - Part Number: 1114 Customer: Yolanda Pérez Hernández Rating: 5 out of 5Overall Opinion: It's all ok. Thank you very much, I liked dealing with you |
| Body Lift Kit - 1 Inch - Part Number: 1114 Customer: Phillip McCoy Rating: 4 out of 5Overall Opinion: Well made, all parts were included, directions gave satisfactory explanations. The only complaint I have (and it may be installer error) is the mount for the grill. If using the two pucks for the sides of the grill (which have no bolts) the center puck with the bolt running through the center has about 2 inches of extra room, which did not seem right to me. Because the original hardware broke in the grill (but allowed me to remove the original puck), I have not installed the new grill puck yet, but it didn't look right when I test fit it. |
| Body Lift Kit - 1 Inch - Part Number: 1114 Customer: ron zapisocki Rating: 5 out of 5Overall Opinion: Great Product I ordered this body lift after receiving a lift kit from Zone. What impressed me the most was the material used in the bushings. We installed this in conjunction with the Prothane 1 1/2" spring spaces and our Jeep rides better and quieter than factory. This also allowed us to install 265/75/16 tires on the TJ. The folks at Energy were excellent!, and the shipping was lightning fast. RZ |
 | Transmission Mount Torque Arms Bushings - Part Number: 11201 Customer: Michael Harper Rating: 4 out of 5Overall Opinion: works fine These do replace the stock torque mount rubber pads. The stock mounts are just plain rubber pucks. The urethane replacements are cast with a tapered cone on one side. There is no direction on how the new ones are to be positioned. Seem to work the way I mounted them. It would be nice if they had an engineering note in the package on the proper orientation. Other than that they look like they will be fine. |
 | Front Track Arm Bushings - Part Number: 11203 Customer: Scott Nichol Rating: 5 out of 5Overall Opinion: Nice quality, good fit. I would have liked to receive a small tube of grease with these bushings. This would have been critical had we not been replacing other bushings that came with the appropriate grease. |
 | Rear Track Bar Bushings - Part Number: 11204 Customer: Randy Martindale Rating: 5 out of 5Overall Opinion: very easy to install Would buy again 2125 |
| Rear Track Bar Bushings - Part Number: 11204 Customer: james miller Rating: 5 out of 5Overall Opinion: Very good part. I am satisfied. Fit well, pretty easy install, and vehicle handles much better. |
| Rear Track Bar Bushings - Part Number: 11204 Customer: TJ Foley Rating: 5 out of 5Overall Opinion: Great Replacement Great stuff, good fit. Lube and press in and your good to go. |
| Rear Track Bar Bushings - Part Number: 11204 Customer: Mike Borean Rating: 5 out of 5Overall Opinion: Quality part, fit perfectly. The parts looked like high quality and fit perfectly. |
 | Front Track Arm Bushings - Part Number: 11205 Customer: Brendan Hayes Rating: 5 out of 5Overall Opinion: Good Product, Easy install Good overall product. Easy to install. Thanks |
 | Rear Track Arm Bushings - Part Number: 11206 Customer: Edward Bender Rating: 5 out of 5Overall Opinion: A little off size First of all, the product listed on the website was listed for my 97 Wrangler. After further research I found (after ordering) that the part was labeled wrong on the web site. The part I ordered was for a WJ. The team fixed my problem after having to renegotiate the correct price. Days later the part was still labeled wrong on their website??? The part itself was OK. I had to drill out the sleeve a little for the bolt to go through. But I did like the 2 piece design. It was very easy to install.
(Editorial Note) The manufacturer lists this kit to fit the 97-06 Jeep Wrangler TJ. |
 | Front Strut Rod Bushing Kit - 5/8 Inch - Part Number: 11207 Customer: Norris Delatte Rating: 5 out of 5Overall Opinion: Good Ok, easy to install and fit good. |
 | Front or Rear Axle Snubbers - Part Number: 11301 Customer: Molly Zeppa Rating: 5 out of 5Overall Opinion: Poor Unfortunately the parts do not fit my jeep, even though they are the correct part per your web site. The parts shipped are approximant 4 inches center to center. The factory ones are approximately 5 3/4 inches center to center So I now need to box them up and send the back at my cost for a refund.............. Eric |
| Front or Rear Axle Snubbers - Part Number: 11301 Customer: Mark Muth Rating: 5 out of 5Overall Opinion: A+++++++ Excellent fit for my 99 Trans Am the car feels like new again! Great product and fast shipping. |
| Front or Rear Axle Snubbers - Part Number: 11301 Customer: Robert Moncrief Rating: 5 out of 5Overall Opinion: Great The description gave the exact dimensions so I was able to make measurements on my 68 International truck. The parts required some mods but that was expected. My suspension no longer bottoms out. Great product, made well, would recommend. |
| Front or Rear Axle Snubbers - Part Number: 11301 Customer: Mario Scarabino Rating: 4 out of 5Overall Opinion: ABSOLUTELY GREAT product These are GREAT snubbers and high urethane quality. I had to modify the mounts slightly to get them to fit though. |
 | Transmission Mount Kit - Part Number: 11601 Customer: alex benn Rating: 5 out of 5Overall Opinion: The part I received is excellent and the service was outstanding as I expected it to take longer to arrive- many thanks Excellent company to deal with, many thanks. The part was just what I ordered and at the right price, many thanks |
 | Drive Train Torque Link Kit - Part Number: 11602 Customer: Maxwell Brown Rating: 5 out of 5Overall Opinion: Nice Easy to install, fits nice and tight. |
 | Front Coil Spring Lift Isolators - Part Number: 11702 Customer: ron zapisocki Rating: 5 out of 5Overall Opinion: Top Shelf Product I really like the quality of these products. When I was searching for spacers for our TJ lift I came across all sorts of different products and materials from rubber to aluminum. Am I ever glad I went with the Prothane, the Jeep rides better and is quieter with this lift installed. Next on my wish list will be the Master Bushing kit! |
 | Front Upper Coil Spring Isolators - Part Number: 11704 Customer: Michael Mahoney Rating: 5 out of 5Overall Opinion: Very good Easy install, good fit. The old part had definite impressions left by the springs. This helped tighten the feel of the front end. |
| Front Upper Coil Spring Isolators - Part Number: 11704 Customer: Charles S Powers Rating: 5 out of 5Overall Opinion: These did not fit the AMC Pacer coil spring or the upper spring cradle. Lucky for me, I was able to put them in a lathe and turn them down to fit. I removed substantial material from inner and outer edges - no more inside lip remaining. |
 | Front Coil Spring Isolators Kit - Part Number: 11706 Customer: paul hosking Rating: 5 out of 5Overall Opinion: exellent fitment Good product, these fit easy |
| Front Coil Spring Isolators Kit - Part Number: 11706 Customer: Barry Davidson Rating: 5 out of 5Overall Opinion: I received the items as described. However they do not fit the vehicles 1964 to1966 Rambler Classic as they are to small. I think they they would fit a Rambler Javelin being a smaller coil spring. I contacted the suppler but they told me you would not have a part to suit this application. Regards, Barry |
| Front Coil Spring Isolators Kit - Part Number: 11706 Customer: Kirk Fletcher Rating: 5 out of 5Overall Opinion: They look and fit fine. Hi Graham, I will not be installing the parts for a couple of months. I am in the process of restoring a 66 1/2 Rambler American V8 Rogue Hardtop. I am in the process of cleaning and refinishing all of my front suspension components and have been buying all of the wear items. I have already checked the fit of these spring insulators in relation to the coil springs and the seats and everything looks fine. Thanks, Kirk Fletcher |
 | Coil Spring Isolator Lift Kit - 2 Inch - Part Number: 11708 Customer: Angel Ruiz Rating: 5 out of 5Overall Opinion: Perfect and easy Perfect. An easy and simple to raise the JK 2" very good product and material. |
 | Motor and Transmission Mount Combo - 6 Cyl - Part Number: 11902 Customer: Georgia Skamaga Rating: 5 out of 5Overall Opinion: great High quality standards |
 | Total Kit - Part Number: 12004 Customer: Kenneth Trueman Rating: 5 out of 5Overall Opinion: good product Used your product when I lived in Mexico. Yes another Cherokee, it worked like a champ!! Ken |
| Total Kit - Part Number: 12004 Customer: Michael S Harriman Rating: 5 out of 5Overall Opinion: Very good upgrade Our 2000 Jeep Cherokee had almost 200K miles on the chassis, the Jeep drove great at highway speeds until you hit a bump; for about 5 seconds after hitting a bump, you had no idea where the Jeep was going to go: to the left, to the right, or straight ahead. After installing the Prothane bushings, the Jeep handles like it did when it was new, stiffer than O.E.. I called the 800 number and ordered my kit, the salesperson was very helpful; I told him what I had and what I wanted. He sold me everything to do the suspension bushings; I did not want to start the project one weekend and not be able to finish it because I did not have everything I need to finish the job. The Instructions were very helpful. The only recommendation I would make is to buy a sheet metal drip pan and put under the bushings when heating/burning the old rubber and sleeve out; the drip pan catches all the molten rubber making clean up a breeze. |
 | Total Kit - AMC 64-69 - Part Number: 12010 Customer: Leo Silveira Rating: 5 out of 5Overall Opinion: Parts installed very easy and the red makes for a really nice look |
 | Total Kit - AMC 70-83 - Part Number: 12011 Customer: George I Hanselman Rating: 5 out of 5Overall Opinion: Overall it's a great kit for my 74 AMC Javelin. The only thing I can think of that would've made it perfect would be the inclusion of a bushing solution for the coil spring seat. |
| Total Kit - AMC 70-83 - Part Number: 12011 Customer: RICHARD DENZLER Rating: 5 out of 5Overall Opinion: ALL PARTS FIT PERFECT ALL PARTS FIT PERFECT AND INSTALLED VERY EASY. ALSO INSTALLED NEW FRONT COIL SPRINGS NOW RIDE IS EXCELLENT THANKS |
 | Front Control Arm Bushings - Part Number: 1206 Customer: S Jones Rating: 5 out of 5Overall Opinion: Very good Only used uppers, but they fit correctly. Recommended |
 | Front Control Arm Bushings - Part Number: 1207 Customer: Daniel R Grambsch Rating: 5 out of 5Overall Opinion: I am impressed I was nervous because the factory type includes the outer metal shell and these do not have them, you use the existing OE shell. I am a mechanic by trade so I have installed many bushings but never by using the OE shells but this was not a problem, very easy install and perfect fit. I am very happy with purchase!! |
 | Front Trunnion Bushings - Part Number: 1209 Customer: paul hosking Rating: 5 out of 5Overall Opinion: exellent product These are a good product work with easy fitment. You guys have got this product right, keep up the good work. I will be back for more products if needed. Thank you |
 | Front Trunnion and Pivot Bushings - Part Number: 1210 Customer: paul hosking Rating: 5 out of 5Overall Opinion: cant beat this product Fantastic product, easy fitment |
| Front Trunnion and Pivot Bushings - Part Number: 1210 Customer: Steve Jones Rating: 5 out of 5Overall Opinion: Very good The vertical bushing was about 1/8" longer than the original. I inserted in the trunnion and trimmed with a razor. I used a nylon lock nut on the vertical and only tightened until I could feel resistance, otherwise if torqued they will bind and steering wheel will return to center without help after making a turn. |
| Front Trunnion and Pivot Bushings - Part Number: 1210 Customer: Steve Swanson Rating: 5 out of 5Overall Opinion: Excellent Perfect fit |
| Front Trunnion and Pivot Bushings - Part Number: 1210 Customer: adrian manvill Rating: 5 out of 5Overall Opinion: excellent hi,pleased with parts,good quality,have fitted only one side at moment,it was a pity the postage to the uk was expensive,but that is not your fault,thanks very much. adrian |
 | Rear Sway Bar and Endlink Bushings - 12.5mm - Part Number: 121109 Customer: Danny Chun Rating: 5 out of 5Overall Opinion: Very good Well made and fits well. Although I wasn't sure where the washers go. It wasn't on the manual. |
| Rear Sway Bar and Endlink Bushings - 12.5mm - Part Number: 121109 Customer: James Leonard Rating: 5 out of 5Overall Opinion: Positive These were purchased for converting a 1996 Miata from a tired street car to a car that will be used on track days at a road course in Virginia. The idea was to complement the polyurethane bushings that were being used elsewhere in the suspension by using these in the key area of the anti-roll bars. The only problem encountered was that the metal sleeves had too small an inner diameter to accommodate the bolts that connect the bar to the suspension. I had to drill each one of the metal bushings larger. Other than that the quality of the product components was excellent. |
 | Rear Differential Bushings - Part Number: 121601 Customer: �ivind ness Rating: 5 out of 5Overall Opinion: Quality product, fitted on my Miata diff perfectly. Requires high pressure to fit and you need to modify the OEM mounts by removing the rubber as these bushings will replace all the rubber in the assembly. Mods took me 15 minutes only. |
 | Total Kit - Mazda MX5 - Part Number: 122002 Customer: Michael Bresnahan Rating: 5 out of 5Overall Opinion: Perfect and easy Perfect kit to replace the worn bushings in my 1994 Miata. Very easy to install - just grease and push both sides into control arms and insert metal tube. Improved handling of car No noise! Very little vibration increase - not enough to impact daily driving. While the overall replacement effort is time consuming i would do this again for any car with an old suspension. |
 | Front Control Arm Bushings - Part Number: 12203 Customer: Joshua Demko Rating: 5 out of 5Overall Opinion: amazing I purchased these bushings because they were cheap and figured i would give them a shot. THEY ARE AMAZING. My old bushings held my front end down and felt like a piece of steel was welded onto them. I burned them off and replaced them with these bushings and about lost it. They are without a doubt PERFECT in every single way. Super soft over bumps cant feel a thing and when I feel like getting up and going they handle excellently through bends and high speed (130+mph) I will definitely be buying more parts from them within the next couple of weeks as a matter of fact. Already recommended to a bunch of my gear head enthusiasts and avid builders to use their parts. Keep up the amazing work guys. XD |
 | Front Control Arm Bushings - Part Number: 12204 Customer: Shane Onuma Rating: 5 out of 5Overall Opinion: All around good buy Great product, fast shipping, wish I'd ordered red.. but that's my fault! |
| Front Control Arm Bushings - Part Number: 12204 Customer: Carlos I Nieves Rubio Rating: 5 out of 5Overall Opinion: Perfet Fit, easy to install Perfect Fit, it feels OK when driving. Very easy to install |
| Front Control Arm Bushings - Part Number: 12204 Customer: Keith Fielder Rating: 5 out of 5Overall Opinion: Best of the BEST! These are the best parts on the market bar none! The folks there are great In the world today it was a great surprise! And the price saved me well over 2 hundred if I had used parts from the local autoparts places Save cash and get great service and the best replacement parts out there TODAY! Keith A. FLA. |
 | Rear Control Arm Bushings - Part Number: 1301 Customer: Nick Kafetzis Rating: 5 out of 5Overall Opinion: Good product easy to use, my car is quiter now. Thank you for a good product and prompt service. I am in Australia and I received my goods faster than some local suppliers. |
 | Rear Sway Bar Bushings - 18mm - Part Number: 131103 Customer: Leslie Regelman Rating: 5 out of 5Overall Opinion: Good Good no problems. |
 | Motor Mount Inserts - 4 Mount Set - 1995-99 - Part Number: 131901 Customer: Elmer Standridge Rating: 4 out of 5Overall Opinion: Good - for track, not for daily driver Motor mount inserts fit properly with no problem. Worked great - but resulted in too harsh a level of engine vibration in the car for a daily driver. Probably great for track - certainly stopped engine twist when torque applied, but removed them and went back to stock for restored Eclipse. |
| Motor Mount Inserts - 4 Mount Set - 1995-99 - Part Number: 131901 Customer: ant Rating: 5 out of 5Overall Opinion: awesome Does not fit Auto Trans. |
| Motor Mount Inserts - 4 Mount Set - 1995-99 - Part Number: 131901 Customer: Dean Rating: 5 out of 5Overall Opinion: Very Nice product! Better than stock! Very Nice product! Better than stock! So glad I purchased these! |
| Motor Mount Inserts - 4 Mount Set - 1995-99 - Part Number: 131901 Customer: Matthew Ross Rating: 5 out of 5Overall Opinion: Great parts Fantastic parts. Was the cheaper solution to my drag car vs solid mounts. HOLDING UP VERY WELL FOR A 742WHP 97 GSX. Oh and easy to install. |
| Motor Mount Inserts - 4 Mount Set - 1995-99 - Part Number: 131901 Customer: Josh Essex Rating: 5 out of 5Overall Opinion: Haven t had a chance to install mine yet but from what I can see its a really solid part. The seller sent me the wrong color which I'm upset about but oh well works the same. |
| Motor Mount Inserts - 4 Mount Set - 1995-99 - Part Number: 131901 Customer: Julio Figueroa Rating: 5 out of 5Overall Opinion: outstanding Very precise and fast service. Parts fit perfectly. A bit hard to install but perfect. |
| Motor Mount Inserts - 4 Mount Set - 1995-99 - Part Number: 131901 Customer: gustavo velazquez Rating: 5 out of 5Overall Opinion: the best motor mounts ***** |
| Motor Mount Inserts - 4 Mount Set - 1995-99 - Part Number: 131901 Customer: The Dude Rating: 5 out of 5Overall Opinion: Great upgrade! These mounts are a great upgrade for every DSM! You can feel much more engine vibration at idle, but I like it like that;-) |
 | Motor Mount Inserts - 4 Mount Set - 1990-94 - Part Number: 131902 Customer: david stitt Rating: 5 out of 5Overall Opinion: They worked great had no problems They were easy to install and would recommend to anyone. |
| Motor Mount Inserts - 4 Mount Set - 1990-94 - Part Number: 131902 Customer: James Lindner Rating: 5 out of 5Overall Opinion: Great product I put these mounts in my 1991 Eagle Talon..Dyno at 645Awhp So I needed a good name brand mount to hold the monster down. Energy Suspension was the only name that came to mind for a good high quality mount! Thanks. |
 | Motor Mount Inserts - 4 Mount Set - 6Cyl Models - Part Number: 131903 Customer: Kary Pabaroue Bailey Rating: 5 out of 5Overall Opinion: Very good product Well it my husband who used it he is a master mechanic and suspension specialist he was tired how quick oem part got worn out he tried out the prothane engine mount package and had great success no vibration smooth no slam between shifts. 1.metal sleeve between front and rear he said had to cut a lil bit off because they were a bit too long , 2 thumbs up to a good product I say. |
| Motor Mount Inserts - 4 Mount Set - 6Cyl Models - Part Number: 131903 Customer: christina brandow Rating: 5 out of 5Overall Opinion: Sweet!!!! Great product!!!!!!! |
| Motor Mount Inserts - 4 Mount Set - 6Cyl Models - Part Number: 131903 Customer: Mark Duffhues Rating: 5 out of 5Overall Opinion: Good Fitted to a Galant vr4 >97 too. Fits good, great support. Nice and fast shipped for a good price. Great improvement to my car :D Thanks! |
| Motor Mount Inserts - 4 Mount Set - 6Cyl Models - Part Number: 131903 Customer: Tony Jaramillo Rating: 5 out of 5Overall Opinion: Great product, amazing results!!! The product shipping was fast. I struggled installing these mounts because of my lack of tools but man o man it was worth that wait, struggle, and sweat. I had to get used to the the new traction, the torque it restored from the beat up old mounts is more than what I expected. Really really happy I bought this. |
| Motor Mount Inserts - 4 Mount Set - 6Cyl Models - Part Number: 131903 Customer: Allen Becker Rating: 5 out of 5Overall Opinion: Good Easy to install with a press. Great Upgrade |
| Motor Mount Inserts - 4 Mount Set - 6Cyl Models - Part Number: 131903 Customer: Gregory Watson Rating: 5 out of 5Overall Opinion: Good I used the mount set on a 1998 Mitsubishi VR4 and they fitted perfectly maybe you could update your site to show other models the mounts fit not just USA models the only way I found out these mounts would work was though a VR4 forum in Australia |
 | Motor Mount Inserts - 4 Mount Set - 4Cyl Models - Part Number: 131904 Customer: Jared Wiley Rating: 4 out of 5Overall Opinion: Good, improved the shifting A decent set of non oem replacement engine mounts, but the rear mount its totally worthless. You have to get it pressed in, and mine still came out of the stock mount before I made it back home to install the thing. Overall though really good, stopped the engine from slapping around. |
| Motor Mount Inserts - 4 Mount Set - 4Cyl Models - Part Number: 131904 Customer: Andrew Cox Rating: 5 out of 5Overall Opinion: Great upgrade for the price My stock mounts had 125k on them and are 9 years old. They wereed and worn out pretty bad. The swap was easy for the front, right, and left, the rear being an insert was a pain and you might want a shop with an arbor press to put them in. Increases the vibration just a bit in the cap but completely removes wheel hop. Not to be done if your looking for smooth comfort but excellent for performance upgrades. |
| Motor Mount Inserts - 4 Mount Set - 4Cyl Models - Part Number: 131904 Customer: Austin Driskill Rating: 4 out of 5Overall Opinion: Satisfied To start off, installation on these isn't straight forward/easy. These require cutting/pressing out the rubber/metal insides of the factory mounts. After dealing with that, you have to find a way to sleeve the front mounts bolt sleeve since its the wrong size. But, if you're ok with dealing with these headaches during install the results are worth it. They beat the heck out of the factory mounts. Great for performance, kills the wheel hop. After replacing my oem mounts, the vibration from having torn mounts improved, but the stiffness of the new ones doesn't make it a whole lot smoother. Nothing I'm complaining about, but others might not like it. |
 | Total Kit - Part Number: 132002 Customer: James Futrelle Rating: 5 out of 5Overall Opinion: Great way to repair the suspension The most difficult part was removing the old bushings metal shell from the front main bushing housing. I had to mount the bushing housing in a lathe and cut them out. I was also surprised to find that the original rubber bushings were filled with fluid or gel when I pressed the rubber part out in the press. |
| Total Kit - Part Number: 132002 Customer: christina brandow Rating: 3 out of 5Overall Opinion: Nice!! Nice product!! but lacked instruction. (Editorial Note) The manufacturer's installation instructions are limited.
|
| Total Kit - Part Number: 132002 Customer: Allen Becker Rating: 4 out of 5Overall Opinion: Great Everything Went Great except I had to make one custom bushing. Otherwise, Great Upgrade |
 | Engine Mount Inserts - Front - Part Number: 13502 Customer: Mike Eells Rating: 1 out of 5Overall Opinion: parts dont fit I have 4 motor mounts on my eclipse. I have three urethane inserts installed but the back roll stop is giving me problems. I don't know if its a wrong manufacturers part number or what, but this is the second time Ive gotten this insert. The second one is exactly the same as the first. Not the right part at all. Its too small, not the right shape, etc. I have a 99 eclipse gsx and I ordered this for the rear roll stop. |
 | Engine Mount Inserts - Right Upper - Part Number: 13503 Customer: Luis Alvarado Thiele Rating: 5 out of 5Overall Opinion: Excellent!!!!! Perfect bushing!! Gives a great look and is a great performance upgrade!! For those Eclipse 1995-1999 with non turbo engine, this bushing will fit the driver side mount!! not the passenger side!!!! Give it a try, its a great item at a great price!!! |
| Engine Mount Inserts - Right Upper - Part Number: 13503 Customer: Carlos Inamagua Rating: 5 out of 5Overall Opinion: Fantastic! I had the parts installed and as soon as I started driving again I noticed a considerable difference in smoothness and control. Definitely a great product! |
 | Engine Mount Inserts - Front - Part Number: 13505 Customer: Steve Sledz Rating: 5 out of 5Overall Opinion: Good quality I've tried them all Whiteline, Works, Torque Solution etc. and trust me - high price does not mean always high quality !!! PROTHANE makes quality bushings for the fraction of the cost of different brands. I've tested them on the Race Track, AutoX, RallyX and Stage Rally and I'm committed to Energy Suspension !!! Great customer service Thanks !!! |
| Engine Mount Inserts - Front - Part Number: 13505 Customer: alexis rivera lessard Rating: 5 out of 5Overall Opinion: Great upgrade to a OEM part. Installing take a little bit of know how with a press but well worth the effort. |
 | Front Shock Mount Bushings - Part Number: 13901 Customer: Romeen Sabahi Rating: 5 out of 5Overall Opinion: Great service in every respect! Shipped out same day as order placed. Great communication. Very user friendly website too. Will be buying all of my Prothane products from them. Thank you! |
 | Rear Leaf Spring and Shackle Bushings - Part Number: 141002 Customer: michael goldsmith Rating: 5 out of 5Overall Opinion: I installed this kit in a 4x4 Nissan D21 Hardbody pickup truck, and the installation and fit of the bushings went great! The only down fall is the tiny amount of grease that is supplied with the bushings, it barely covered all the surfaces the instructions stated to grease, and am worried I'll be doing this job again in 6 months; greasing it again to remove those pesky polyurethane squeaks. |
 | Rear Leaf Spring and Shackle Bushings - Part Number: 141003 Customer: peter lybolt Rating: 5 out of 5Overall Opinion: toolboy6913@yahoo.com The old ones were tough to take out, but the new ones went in a little easier with a little forcing. My truck rides totally different now. Well the old ones were wiped out. I like them and I would get them again. Thank you! |
| Rear Leaf Spring and Shackle Bushings - Part Number: 141003 Customer: John McCoy Rating: 5 out of 5Overall Opinion: Very satisfied I highly recommend them, they are great parts that fit perfectly. I would only add a sheet that depicted which bushing went to which part of the suspension. There are 2 sets of bushings that are very, very similar in size. It is crucial they are put in their proper place. I had to trial and error it, to find which went where. Still not a bad experience at all. |
| Rear Leaf Spring and Shackle Bushings - Part Number: 141003 Customer: Vonne Metcalf Rating: 5 out of 5Overall Opinion: Okay Truck rides stiffer. My son doesn't like to ride with me anymore unless he has to ....pick up from school. They say the rubber ones would be better. |
 | Rear Subframe Bushings Kit - Part Number: 14101 Customer: Corey R Larkin Rating: 5 out of 5Overall Opinion: Great product Thanks for having such a great product at a great price. I actually had a shop turn down doing the repair on my 300zx... I have a friend at a dealership here that let me bring it in on a Saturday. It only took us an hour and a half to get these new bushings in. Thanks a million! |
| Rear Subframe Bushings Kit - Part Number: 14101 Customer: A.D. Rating: 5 out of 5Overall Opinion: Perfect fit for 1988 Nissan 200SX if you just shave a bit off the top! I purchased these with the intention of modifying them for the subframe on my 1988 Nissan 200SX SEV6. Just had to shave a bit off the top and they are a perfect fit! |
| Rear Subframe Bushings Kit - Part Number: 14101 Customer: Chuck Rating: 5 out of 5Overall Opinion: Good Fix!!!! These work perfectly for getting rid of the annoying clunking sound. Really tightens up the back end and improves rear shock absorption. Adds a little more drive line noise than was noticed before, but not too bad. The shop I used put the car on a lift, then put a support stand under the member, removed the stays from each side, then took a reciprocating saw to the old bushings to remove them. The new ones slipped right in. Easy fix in shop, took mechanic 30 minutes total. |
| Rear Subframe Bushings Kit - Part Number: 14101 Customer: Durrell Rating: 5 out of 5Overall Opinion: Very Satisfied. The replacements slide in fairly easy (after the hassle of getting the old OEM bushings out of course). |
| Rear Subframe Bushings Kit - Part Number: 14101 Customer: Lars Ostervold Rating: 5 out of 5Overall Opinion: Fantastic! Relatively easy installation - had to modify the directions (which were correct), but I had a bolt that wouldn't come out of the rear cross-member. The product works perfect - better handling, fixed the rear end "thump" common in 300zx. Will replace other suspension components with similar poly components. |
| Rear Subframe Bushings Kit - Part Number: 14101 Customer: Morgan Doyle Rating: 5 out of 5Overall Opinion: Perfect Part fit perfectly and the dreaded 300zx clunk went away. |
| Rear Subframe Bushings Kit - Part Number: 14101 Customer: luke Rating: 5 out of 5Overall Opinion: great Very easy install, easier than oem. Very solid without sacrificing comfort. |
| Rear Subframe Bushings Kit - Part Number: 14101 Customer: Robert Aldrin Rating: 5 out of 5Overall Opinion: Excelente Excelente si problema extacto Desde Costa Rica Gracias |
 | Front Sway Bar Bushings and Endlinks - 23mm - Part Number: 141102 Customer: John McCoy Rating: 5 out of 5Overall Opinion: These are great quality parts. Im very satisfied. Excellent customer service, fast shipping, and quality parts! The correct parts were shipped, and they fit perfectly. I highly recommend them! |
 | Front Sway Bar Bushings - 18mm - Part Number: 141105 Customer: Daniel Frye Rating: 5 out of 5Overall Opinion: Parts fit perfectly!!! |
 | Front Sway Bar and Endlink Bushings - 20mm - Part Number: 141106 Customer: Eric Venette Rating: 5 out of 5Overall Opinion: not happy Bad fit. The hole in the bushings was too small of a diameter, and the base had to be trimmed in order to get close to fitting in the brackets. I basically just trimmed them to fit on a bench grinder and put it back together because I had to get it back together and rolling that night. |
 | Rear Sway Bar Bushings - 22mm - Part Number: 141112 Customer: robert sayles Rating: 5 out of 5Overall Opinion: Great Great product! |
 | Rear Sway Bar Bushings - 21mm - Part Number: 141116 Customer: Charles Taylor Rating: 5 out of 5Overall Opinion: Perfect fit I have a high mileage Z and noticed the difference in handling immediately. |
| Rear Sway Bar Bushings - 21mm - Part Number: 141116 Customer: Reynier Negrón Rating: 5 out of 5Overall Opinion: Very happy with the product overall Very easy to install; I used a set of aftermarket (Eibach) sway-bars an the install was easy, the metal bracket is thicker and more stout than the OE bracket, so i know the bushings will stay put. Overall, I am very satisfied, and will not hesitate to use Prothane for the rest of my bushing needs. |
 | Front Sway Bar and Endlink Bushings Kit - 24mm - Part Number: 141117 Customer: Guillermo Arroliga Rating: 5 out of 5Overall Opinion: Awesome This product is great stiffened my ride up from the original bushing. Will definitely be upgrading all the other bushings. |
 | Front Sway Bar and Endlink Bushings Kit - 25mm - Part Number: 141118 Customer: Jimmy Santos Rating: 5 out of 5Overall Opinion: Thank you for the parts. They work great the installation was easy. These parts make my car more responsive to my turning. |
| Front Sway Bar and Endlink Bushings Kit - 25mm - Part Number: 141118 Customer: Travis frensky Rating: 5 out of 5Overall Opinion: great product made the car feel great easy install and perfect fit |
 | Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: Adam Weller Rating: 5 out of 5Overall Opinion: great product. works perfectly these took minutes to install and work great. |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: Arthur D Rees Rating: 5 out of 5Overall Opinion: Great! I used these bushings to tighten up the sway bar to frame connection on my 2006 Nissan Frontier. The bushings are for a Titan and are a little different than the stock Frontier parts however they installed with no modifications needed. Turn in is much improved as well as the trucks ability to track strait over small bumps at freeway speeds. Very good upgrade to the stock rubber bushings which were worn out at less than 50k mi. |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: Jesse Davis Rating: 5 out of 5Overall Opinion: Installed easy and good Quality. |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: Patrick McGinnis Rating: 5 out of 5Overall Opinion: Fantastic on my Frontier! I bought these for my 06 Frontier and it made drastic difference in steering feel. You must keep them greased or they will squeak (like any poly bushing) but overall a great product! |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: Gregg Christopher Rating: 5 out of 5Overall Opinion: They work well This is my 3rd set of Prothane bushings in my 2006 Nissan Titan in as many years. The roads between Leominster and Fitchburg MA are full of holes and patches which eat any bushing fairly quickly. Many folks overlook these small inexpensive parts but they're easy to change and make a world of difference in the squeak and clunk department on my 4x4 truck with its slight 1.5" lift. I think I'll change em out again after winter before I put my summer wheels and tires back on. Not that they'd need it. I'm just fussy that way! |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: David Floyd Rating: 5 out of 5Overall Opinion: great product Just what I needed and bolted on in minutes. |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: Rafal Zep Rating: 5 out of 5Overall Opinion: Great FIT Works great. Better handling than stock rubber bushings. |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: Daniel Garcia Rating: 5 out of 5Overall Opinion: Perfect fit, works great, nice product thanks. |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: John Alexander Rating: 5 out of 5Overall Opinion: Quality parts They were very easy to install and seem to work fine. Great replacement for the stock rubber bushings. |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: James LeDune Rating: 5 out of 5Overall Opinion: Very Nice, Great Quality Well I purchased these bushings to see if it would eliminate a squeak that my Nissan dealer said they could not recreate, I told then I felt it was the bushing but the dealer said the original was still good... so I purchased these bushings from "Energy Suspension". The price was the best I had seen and they shipped it super fast and at a very reasonable price! Needless to say I was very impressed with it. So I went ahead and removed the stock Nissan bushings and installed these Prothane Bushings and now no squeak in fact it seams more nimble which is great! I'm very happy with my purchase and would Highly recommend the product for those looking to replace their originals or worn out bushings! In fact, I plan to purchase another set just as a back up in case. Just a totally Awesome buying experience!! Energy Suspension you guys rock! |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: Allan Fone Rating: 5 out of 5Overall Opinion: Perfect Bushings fit exactly like stock. A tad more firmness in the turns just like I ordered. Mine were black which makes no difference, because it is all in the material that the bushings are made out of. Parts for a Titan. Thanx, AL Fone. |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: Jason Hensley Rating: 5 out of 5Overall Opinion: Good Product Product worked very well on my 2008 Armada. Ordered based on the information I received from ClubArmada.com. Great resource. |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: Felix Osedowsky Rating: 5 out of 5Overall Opinion: Installed the parts. Perfect fit and there is a noticeable improvement in handling. I'm very happy with the product and the service I received. Thanks |
| Front Sway Bar Bushings Kit - 34mm - Part Number: 141123 Customer: John Rennich Rating: 4 out of 5Overall Opinion: Better than OEM I do wish that the split on the bushings was in a different spot. Considering where they come together is the part that presses against the frame. I know all other options are setup the same way so it is not a knock against this product. These were easy to install and way better than OEM. Fixed my problem. |
 | Front Strut Rod Bushings - Part Number: 141202 Customer: yoel ruiz Rating: 5 out of 5Overall Opinion: I had no problems with your product and I'm satisfied. Thank you. |
 | Front Strut Rod Bushings - Part Number: 141203 Customer: Edward W. Rating: 5 out of 5Overall Opinion: Excellent The improvement in tracking down the road and general handling is dramatic on this old 300ZX. It was very easy to do, everything fit fine, and I highly recommend doing this inexpensive upgrade. If you have a first generation 300ZX (84-89) I would consider this a safety issue, do it today! |
| Front Strut Rod Bushings - Part Number: 141203 Customer: James Hunt Rating: 5 out of 5Overall Opinion: Great Product! I bought these for an 88 Nissan 200sx and they fit fine but I ended up not using these bushings as they were firmer than I wanted. So I ended up buying rubber bushings instead. I did read a suggestion though about drilling holes in these to help them be a little more flexible than they are and that may help but I didn't try it. However I did notice the rubber bushings I bought in place of these came with several holes drilled in them and they are very flexible. So it might be an idea worth trying on these. |
 | Front Strut Rod Bushing Kit - Part Number: 141205 Customer: Jason Mermuys Rating: 5 out of 5Overall Opinion: Excellent Product My mechanic gave me a price on a set of split bushings for a lot more money and not near the quality of this product. After I received the product I took them to him and he wanted to know where I got them. Very Impressed with the quality, shipping, and customer service. They just made a life long customer. |
| Front Strut Rod Bushing Kit - Part Number: 141205 Customer: Adam Rating: 5 out of 5Overall Opinion: Prothane Bushings for 240sx = win I installed two front strut rod bushings and two lower control arms to replace my very old and worn stock ones. It tightened up my steering feel and reduced a bit of subframe play that happened upon hard cornering or braking. I have noticed an immediate improvement in day to day driving, and am looking forward to the next autocross. |
| Front Strut Rod Bushing Kit - Part Number: 141205 Customer: Ray Ishihara Rating: 5 out of 5Overall Opinion: Part works fine and delivery service excellent Actually, I bought the strut rod bushing for my garage to install, because his supplier sold only a complete strut rod that would have cost me almost 10 times more. He wanted to use a one-piece bushing instead of the 3-piece Energy Suspension bushing. He was satisfied with the results. |
 | Mustache Bar Bushings - Part Number: 141602 Customer: keith krogel Rating: 5 out of 5Overall Opinion: I got this very soon after ordering it. The parts are very well made. However, make sure you put the two urethane pieces together then hammer the cylinder through. If you don't an airtight will form and the piece will not sit right. Great piece of work |
| Mustache Bar Bushings - Part Number: 141602 Customer: Ian Mcdaniel Rating: 5 out of 5Overall Opinion: Worked great It would have been nice to have instructions to put Prothane grease on all areas of bushings. Ended up making squeaking noises and had to remove and re-grease. (Editorial Note) For assistance with installation Prothane can be contacted directly at this number: 1-888-776-8426 |
 | Motor Mount Inserts - 4 Mount Set - Part Number: 141901 Customer: Nicholas Winchester Rating: 5 out of 5Overall Opinion: Great! I got excited as soon as I started the engine! You can feel the vibration in the steering wheel at idle. Not a problem though, it goes away when you start moving. The ride feels better, maybe even a little stiffer. They are perfect! |
| Motor Mount Inserts - 4 Mount Set - Part Number: 141901 Customer: walter e gasowski Rating: 5 out of 5Overall Opinion: I like them Other than having to slightly trim the drivers side insert these are great for the price |
| Motor Mount Inserts - 4 Mount Set - Part Number: 141901 Customer: Vladimir Brkicic Rating: 5 out of 5Overall Opinion: very good prodcut Very good product, had to make little modifications but it was mostly plug and play. ;) Car doesn't jump on high rev shifting at all, they are really stiff and make all the chassis vibrate, but I like it, sounds racing :) |
| Motor Mount Inserts - 4 Mount Set - Part Number: 141901 Customer: Michael Knoll Rating: 5 out of 5Overall Opinion: perfect fit on euro nissan 100 nx gti SR20DE You need a press for the inserts. |
| Motor Mount Inserts - 4 Mount Set - Part Number: 141901 Customer: Juan Javier RodrÃguez Expósito Rating: 5 out of 5Overall Opinion: Perfect I have installed these and they are all perfect. |
| Motor Mount Inserts - 4 Mount Set - Part Number: 141901 Customer: James D. Lewellen Rating: 5 out of 5Overall Opinion: Beyond Impressed!! While you need a press to install most of the bushings and have to trim the passenger side bushing slightly, these are absolutely GREAT!! The added stability really helps with power transfer and my transmission feels much more tight. Couldn't be more impressed! |
 | Total Kit - Part Number: 142003 Customer: Hans Bosman Rating: 5 out of 5Overall Opinion: jockhuyzen@ziggo.nl Thanks for delivery to the Netherlands |
| Total Kit - Part Number: 142003 Customer: Lemon, Cole David Rating: 5 out of 5Overall Opinion: Very impressed! I have been very impressed with the customer service here, and quick response time! Although I have not had time to install this kit yet, I've been told by mechanics that the quality is very good! I have been very pleased with the over all quality of product and customer service. |
| Total Kit - Part Number: 142003 Customer: Andrew K Jacobsen Rating: 5 out of 5Overall Opinion: Good. I like the kit. It stiffens things up real good. However, the front control rod bushings are too tight. It took more effort than I'm comfortable with to torque them down. The tube for them needs to be 1/8 inch longer to avoid this problem. |
 | Front Control Arm Bushings - Part Number: 14203 Customer: Thomas Kaminski Rating: 5 out of 5Overall Opinion: Great They fit perfectly, very good product. |
 | Front Control Arm Bushings - Lowers Only - Part Number: 14206 Customer: Rhonda Smith Rating: 5 out of 5Overall Opinion: Excellent Excellent service, parts are excellent quality. I wish I could get all my parts with this kind of service. |
| Front Control Arm Bushings - Lowers Only - Part Number: 14206 Customer: Duncan Burns Rating: 5 out of 5Overall Opinion: Great Replacement Product fit great....as long as you can get the old bushing out!! BURN BABY BURN!!!!! Great product would recommend!! |
 | Front Control Arm Bushings - Part Number: 14207 Customer: Teh Jin Shoon Rating: 5 out of 5Overall Opinion: Perfect! No weird squeaking sound. Installation is tight fit upon putting in the metal tube. Gets everything right back to the geometry, not too harsh as I don't feel any increase in vibration . However road feedback and response is good. I installed it together with the power steering rack bush. Not sure whether this pair of bush or the steering rack bush did more work.. but having them both together, my steering response, turn-in and feedback is almost immediate.. Thumbs up ... highly recommended |
 | Front Lower Control Arm Bushings - Part Number: 14208 Customer: Gairy Plummer Rating: 5 out of 5Overall Opinion: Excellent items. Installed these as soon as I got them and what a difference. I love driving my car again. My car feels solid again. Thanks guys. |
| Front Lower Control Arm Bushings - Part Number: 14208 Customer: Jean-Luc Vida Rating: 5 out of 5Overall Opinion: A+++ Woooooo!! |
 | Front Control Arm Bushings - Part Number: 14210 Customer: mohammed albasha Rating: 5 out of 5Overall Opinion: very pleased I like this kit soooo much . Now the car handles way better. No noises at all in front end any more . Definitely recommend |
 | Rear Lower Control Arm Bushings - Part Number: 14305 Customer: David Theriault Rating: 5 out of 5Overall Opinion: It's a very good product. |
 | Motor Mount Inserts - Driver or Rear - Part Number: 14501 Customer: joe franco Rating: 5 out of 5Overall Opinion: Great Part Great quality part. Fit perfect. |
| Motor Mount Inserts - Driver or Rear - Part Number: 14501 Customer: Patricio Andres Muñoz Lopez Rating: 5 out of 5Overall Opinion: great very good product the shifter works great now, no more 1st gear problem installation was a little bit complicated but not impossible thanks for the product Greetings |
 | Motor Mount Inserts - Passenger - Part Number: 14502 Customer: Dillon Fruzia Rating: 5 out of 5Overall Opinion: great! works for transmission mount on the se-r spec-v Great! Works for transmission mount on the se-r spec-v |
| Motor Mount Inserts - Passenger - Part Number: 14502 Customer: valiant brown Rating: 5 out of 5Overall Opinion: Great product The parts came in and where of high quality in fit and feel. Thanks Prothane. |
| Motor Mount Inserts - Passenger - Part Number: 14502 Customer: Lucas Goodwin Rating: 5 out of 5Overall Opinion: Delicious I use these for tranny mounts in B15 2002-2006 Sentra SE-R Spec Vs and they work great. They just need some shimming from a few 3/8 washers and they work like a charm. |
 | Motor Mount Inserts - Front Mount - Part Number: 14504 Customer: toyboytbfb Rating: 5 out of 5Overall Opinion: Great! Mounts are easy to install if you have a lift or autoshop you can go to otherwise probably a pain in the ass or impossible. Tip for anyone trying to install these, use WD-40. I pressed the inserts in fairly easy with my foot. Overall the inserts got rid of most, if not all, of my wheel hop. Great product! |
| Motor Mount Inserts - Front Mount - Part Number: 14504 Customer: Karim Lawandy Rating: 5 out of 5Overall Opinion: pretty good would recommend them Thought it would be easy to install but was proven wrong. Drivability: HUGE difference especially when power shifting and take off. Problem is a lot of vibration, had to lock tite the bolts holding the fenders and such. When at idle and switch the A/c on the car vibrates like crazy. |
 | Steering Rack and Pinion Bushing Kit - Part Number: 14702 Customer: Hervé PHILIPPE Rating: 5 out of 5Overall Opinion: excellent product ! A real improvement for my Z |
 | Steering Rack and Pinion Bushing Kit - Part Number: 14703 Customer: Mat Peck Rating: 5 out of 5Overall Opinion: Works well, installation was a bit of a pain. I've used these on two different 1978 280Zs. They firm up the steering very much, and I would strongly recommend pairing them with a polyurethane steering puck. The play in the stock rubber bushings is greatly reduced, which gives a much better response and road feel. The shape of the bushings make them somewhat hard to install with the rack still in the car. It is possible to loosen the two bolts that hold the top bracket of the rack from underneath the car, which is what I did. Estimated install time is about 30 minutes. - Mat [FlatBlack] |
 | Steering Rack Bushings - Part Number: 14705 Customer: steven deleon Rating: 5 out of 5Overall Opinion: I had no idea how much of a difference this part would make. I know exactly where the wheels are when changing angle. Super responsive steering, way stiffer feel one of my best purchases by far. Just wish u made them for 1994 rx7s |
 | Motor Mount Inserts - V8 Models - Part Number: 1504 Customer: Edward McClure Rating: 5 out of 5Overall Opinion: WOW Love them! Motor doesn't hardly move. thx bunches |
 | Rear Sway Bar Bushings - 17mm - Part Number: 161102 Customer: brian alvarez Rating: 5 out of 5Overall Opinion: good Good product, much improvement over stock. Great price and fast shipping. The only problem I had was installation. There was no relief cut to easily put the bushings on, a little struggle to slip over the sway bar endlink mounting tab, but other than that, works good. |
| Rear Sway Bar Bushings - 17mm - Part Number: 161102 Customer: Carlos Trejo Rating: 5 out of 5Overall Opinion: Great product Thanks to Energy suspension Rear Sway Bar Bushings my car AWD Subaru Impreza WRX turbo is in perfect condition. Thank you once again Regards: Carlos |
 | Rear Sway Bar Bushings - 20mm - Part Number: 161104 Customer: Christian Pfeiffer Rating: 5 out of 5Overall Opinion: Great! These were shipped quickly, were priced right and fit perfectly in the mounting brackets for my rear sway bar. Highly recommend. |
| Rear Sway Bar Bushings - 20mm - Part Number: 161104 Customer: Scott Reichenbach Rating: 5 out of 5Overall Opinion: Amazing product!! The guys at Energy Suspension are great! Products are just as advertized and the fitment was perfect. Keep up the good work guys, i will definitely be buying from you again in the near future. -Scott |
 | Shifter Bushings - 6 Speed STi - Part Number: 161603 Customer: virgilio viduya Rating: 5 out of 5Overall Opinion: good I run into slight problem with the rear shifter bushing (wrx sti 6 speed). The upper part hitting the under body and have to trim some off. But overall I like how my car shift compare to the stock bushing. |
 | Total Kit - Part Number: 162001 Customer: Andrey Kuznetsov Rating: 3 out of 5Overall Opinion: This kit contains all the bushings for front suspension of Subaru Impreza 03. But there's only rear trailing arm bushings fits correctly for rear suspension. 17 mm rear sway bar doesn't fit, cause it doesn't has flanges. And this kit doesn't contain rear lateral links bushings. So, its not total kit. |
| Total Kit - Part Number: 162001 Customer: Augustine Tan Rating: 5 out of 5Overall Opinion: I am very satisfied with this product the only thing that was not the same was the rear stable bar OD is not the same mine is 19mm while the ones sent to me were 17mm but the rest was a perfect fit |
 | Front Control Arm Bushings - Part Number: 16201 Customer: Eric L. St-Jean Rating: 4 out of 5Overall Opinion: Great bushings. Awesome bushings, easy install, ride is much stiffer. If NVH is a concern, don't install these, but if handling and responsiveness is your goal, you'll love these. Although I'd did have to trim the width of a pair of bushings and metal races. They were about 10 mm too wide for my application (Impreza 98). My bad ordering... But rest fit great! |
| Front Control Arm Bushings - Part Number: 16201 Customer: ryan evelo Rating: 5 out of 5Overall Opinion: Parts were great The parts worked great and installed easy, the only issue I had was removing the stock bushings. You must have a hydraulic press |
 | Rear Trailing Arm Bushings - Part Number: 16301 Customer: Eric L. St-Jean Rating: 5 out of 5Overall Opinion: Great bushings! Awesome bushings, easy install, ride is much stiffer. If NVH is a concern, don't install these, but if handling and responsiveness is your goal, you'll love these. |
| Rear Trailing Arm Bushings - Part Number: 16301 Customer: thomas klein Rating: 5 out of 5Overall Opinion: Great product Great parts, and easy install. Less than half the price of stock bushings with better performance. |
| Rear Trailing Arm Bushings - Part Number: 16301 Customer: Robert Lund Rating: 5 out of 5Overall Opinion: Great upgrade This removed the unstable feeling of the rear end through high speed corners, made the rear turn in much better and actually made shifting gears feel much better due to the sharper response of the rear end. This was my last - and actually best upgrade of bushings in the rear end. No NVH noticed. |
 | Front Leaf Spring Bushings - for use with Aftermarket Shackles - Part Number: 171002 Customer: Scott Comeaux Rating: 3 out of 5Overall Opinion: Its A fit! It fits but needs modifications to make it fit! |
| Rear Leaf Spring Bushings - for use with Aftermarket Shackles - Part Number: 171002_rear Customer: Scott Comeaux Rating: 3 out of 5Overall Opinion: Its A fit! It fits but needs modifications to make it fit! | |
 | Front Sway Bar and Endlink Bushings - 22mm - Part Number: 171101 Customer: Woody Cortner Rating: 5 out of 5Overall Opinion: Excellent Easy to install, excellent fit. Great parts for the money! |
 | Front Frame Shackle Bushings - Part Number: 1803 Customer: Ben Thomas Rating: 5 out of 5Overall Opinion: easy to install The bushings were an easy installation and they are holding up very well. |
 | Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 181002 Customer: Daniel Poland Rating: 5 out of 5Overall Opinion: Love them They fit perfectly. It took me all of 15 min to install. |
| Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 181002 Customer: Max McGuire Rating: 5 out of 5Overall Opinion: Mcguire_max@yahoo.com These parts were an exact fit for my conversion using 85 Toyota mounts it was one of the easiest parts to install & they work perfectly go ahead buy some with confidence that you wont be dissatisfied. |
| Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 181002 Customer: Terry K Carrow Rating: 5 out of 5Overall Opinion: Great quality/great results After the installation of these bushings, our 4Runner now rides even better than stock, and that's with 3" of lift and 35s |
 | Rear Spring Eye and Shackle Bushing Kit - Part Number: 181006 Customer: edward jenkins Rating: 5 out of 5Overall Opinion: very good good fit easy to work The bushings had all I needed to fit my truck also had extra parts to fit other trucks of different years. The bushings were of very high quality material. They will last longer than the truck itself. They also had a very good price, cheaper than local parts house.They did not have what I needed at the time I ordered. Told me they were on back order. They offered to refund my money or they would have my parts in about 2 weeks. The parts were at my house in less than 10 days. I thought that was above the call of duty. Good people to deal with I --WILL BUY FROM THEM AGAIN---thanks Edward Jenkins from Charlotte N.C. |
| Rear Spring Eye and Shackle Bushing Kit - Part Number: 181006 Customer: Edvard Henriksen Rating: 5 out of 5Overall Opinion: Good The bushings felt like they were of good quality. The only downside was that I had to saw them off a bit, but that wasn't a big problem. |
| Rear Spring Eye and Shackle Bushing Kit - Part Number: 181006 Customer: Ryan Chapman Rating: 3 out of 5Overall Opinion: Quality manufacture, but... The shackle bushings do not fit a 2000 Tacoma 4x4. The diameter of the bushing was just too large to make them work. |
| Rear Spring Eye and Shackle Bushing Kit - Part Number: 181006 Customer: Mark A McAllister Rating: 5 out of 5Overall Opinion: Impressed East fit, easy fix..like new |
 | Body Mount Bushings and Radiator Support Bushings - Part Number: 18101 Customer: Nathan Morales Rating: 5 out of 5Overall Opinion: Adequate I found the parts were a good fit for my vehicle, but why they didn't send all the washers required to complete the installation is a myth to me. I would have paid extra money to have everything I needed. |
| Body Mount Bushings and Radiator Support Bushings - Part Number: 18101 Customer: Jeremy Hayden Rating: 5 out of 5Overall Opinion: Hi Yes I have fitted these and found them to be very suitable for my application and great quality too, and your customer service was spot on. I fitted this part to a 1982 HJ47 Toyota Land cruiser Ute - not sure it was the exact application intended but some model descriptions vary from country to country (I am in Australia). Regardless, the parts were great. Cheers Jeremy |
| Body Mount Bushings and Radiator Support Bushings - Part Number: 18101 Customer: Buck Rating: 5 out of 5Overall Opinion: Great quality, exceptional service Very good quality parts. I bought this kit for use on a totally different vehicle. It worked out great. A big part of that was based on the completeness of the information on this website. The company was excellent to work with. Parts were correct, packaged well, and shipped very quickly. I look forward to future business, and highly recommend them. |
 | Body Mount Bushings - Part Number: 18103 Customer: Jason Cho Rating: 5 out of 5Overall Opinion: high quality product Very well designed product, high quality materials. Ride stiffness increased, as expected. Many companies have made body lift blocks that sit on the mounts but have one drawback....they are cheap plastic cylinders that rely on bolt tension to stay in place. If your company could design a body mount replacement that was thicker above the perch to give body lift, I think it would be much more superior and safer design than what is available today. |
 | Front Sway Bar Bushings and Endlinks - 24mm - Part Number: 181108 Customer: Jan-Boerre Olsen Rating: 4 out of 5Overall Opinion: Great bang for the buck This is a real cheap alternative for OEM spare parts but it does the job just as good. All in all this is a good buy for anybody who need to change the sway bar link if the old one is worn out like mine was. |
| Front Sway Bar Bushings and Endlinks - 24mm - Part Number: 181108 Customer: Miguel Puig Rating: 5 out of 5Overall Opinion: Great Product Installed them on a 94 Toyota Pickup. Installed very easily. Preformed better than expected. I would recommend. |
| Front Sway Bar Bushings and Endlinks - 24mm - Part Number: 181108 Customer: �istein Drangberg Rating: 5 out of 5Overall Opinion: Very good parts and very fast shipping! Fast shipping, and the parts fitted perfect. - My 20 years old car feels tighter and some years younger. I will definitely buy from you again if I should need more bushings etc. Thanks! :-) |
 | Rear Sway Bar and Endlink Bushings - 18mm - Part Number: 181110 Customer: Ryan Ayers Rating: 5 out of 5Overall Opinion: Very Good For all of you erratic drivers out there, these are made for you! A replacement for your OEM anti-sway bar bushings that will stiffen those turns by taking all of that slop and extra movement that rubber bushings twist to accommodate, and stand up to the pressure. Like I said, I recommend these for anyone who drives like a maniac and intends for their passengers to soil themselves. |
| Rear Sway Bar and Endlink Bushings - 18mm - Part Number: 181110 Customer: john abernethy Rating: 5 out of 5Overall Opinion: Parts and service top notch |
 | Front Sway Bar Bushings and Endlinks - 27mm - Part Number: 181111 Customer: Greg Price Rating: 5 out of 5Overall Opinion: gregtbr@aol.com Parts fit just fine, and look to be of good quality. Also great service from ESP.com Thanks! |
 | Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: Danton Rezos Rating: 5 out of 5Overall Opinion: Great replacement bushing for the 3rd Gen. Toyota 4runner, and Tacomas as well if they run the same sway-bar linkage This product is made for the 3rd Gen. Toyota 4runners, and possible the Tacoma of those years. They are exact replacements for the front sway-bar bushings. Excellent product and will do business again when need be. Dan |
| Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: Jc Rating: 5 out of 5Overall Opinion: Great product - easy install Installed this set on my 96 4runner 4x4. The installation took only 30 minutes and easy to install. |
| Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: Jeremy Ports Rating: 5 out of 5Overall Opinion: Excellent product I ordered these for my 2000 Toyota 4Runner that is equipped with a 3 1/2" lift kit. The stock ones blew out almost immediately after the lift was installed. I have had the Prothane ones installed for almost two month and they are amazing. All of my front end noise went away and I don't have the floating sensation in the front end anymore. Super fast shipping and they come with installation grease which was ideal. Superb product. |
| Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: Alan Gillette Rating: 5 out of 5Overall Opinion: Excellent Kit was reasonably priced and arrived in good time. Installation was simple and hassle free. Performance is notably better than stock rubber, but stock bushings were quite worn so that may not mean much. Longevity is uncertain due to relatively recent install. I would buy this again. I would recommend it to friends. |
| Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: Shannon Hazard Rating: 5 out of 5Overall Opinion: Great These items installed nicely onto the original sway bar and end links, I was very happy with the end result. |
| Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: Peter C Stryker Rating: 5 out of 5Overall Opinion: The parts fit with no problems. Thanks |
| Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: Marc Cerri Rating: 5 out of 5Overall Opinion: Installed on my 2000 4Runner with no problem. Steering feels more responsive now, makes the vehicle feel new again! |
| Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: Robert Condon Rating: 5 out of 5Overall Opinion: Great quality and all the necessary parts for install. I am very pleased with the sway bar bushings. The shipping was very prompt and arrived with all the necessary parts. The bushings fit perfect and provided a much improved ride from my stock bushings. I highly recommend using this product! |
| Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: matthew j simao Rating: 5 out of 5Overall Opinion: Great, definitely will buy from again Great parts, great service, fast shipping @ good prices! |
| Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: Ronald Wells Rating: 5 out of 5Overall Opinion: Great product The new parts definitely has made a noticeable improvement to my front suspension. |
| Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: Stuart Pearce Rating: 5 out of 5Overall Opinion: good product your product installed fine. Rusty bolts were the challenge. I'm anxious to see how they do in a couple of years. |
| Front Sway Bar and Endlink Bushings - 26mm - Part Number: 181115 Customer: Howard White Rating: 5 out of 5Overall Opinion: Very good The bushings were nearly a perfect fit. The amount of grease provided was more than adequate. The handling was greatly improved. Overall an excellent value. |
 | Rear Sway Bar and Endlink Bushings - 19mm - Part Number: 181116 Customer: Robert Condon Rating: 5 out of 5Overall Opinion: Great product and service. I am very pleased with the sway bar bushings. The shipping was very prompt and arrived with all the necessary parts. The bushings fit perfect and provided a much improved ride from my stock bushings. It was nice to have new washers for the endlinks as well. I highly recommend using this product! |
| Rear Sway Bar and Endlink Bushings - 19mm - Part Number: 181116 Customer: Marc Cerri Rating: 5 out of 5Overall Opinion: Installed on my 2000 4Runner and fit great! |
| Rear Sway Bar and Endlink Bushings - 19mm - Part Number: 181116 Customer: Alfred S Braconnier Rating: 5 out of 5Overall Opinion: Great Customer Support Ordered parts, they were not in stock at the time but Graham made it a very fast delivery. When parts got in, they were the right ones as I ordered and he threw in extra for my wait. Would Highly Recommend Friends And Family To Buy Parts From His Company. Thanks Again From A Very Satisfied Customer |
| Rear Sway Bar and Endlink Bushings - 19mm - Part Number: 181116 Customer: Shannon Hazard Rating: 2 out of 5Overall Opinion: Dissapointed Unlike the front bushing kit, these come with their own brackets to secure the sway bar bushings. The brackets were very difficult to install as the fit was extremely tight, also the washers that were supplied with this kit needed some grinding in order to fit. I would have been much happier with this kit if the sway bar bushings had been larger so they could have been installed into the original brackets that held the rubber ones. |
| Rear Sway Bar and Endlink Bushings - 19mm - Part Number: 181116 Customer: manuel a repollet Rating: 5 out of 5Overall Opinion: Performs great First thank you for having these part available. My truck runs smoother then ever ..... |
| Rear Sway Bar and Endlink Bushings - 19mm - Part Number: 181116 Customer: Jc Rating: 5 out of 5Overall Opinion: Great product - easy install Installation was easy and took less than half-hour. Has all the necessary parts and some additional ones. Installed on 96 4Runner 4x4. |
 | Front Sway Bar and Endlink Bushings - 23mm - Part Number: 181117 Customer: Charles E Shampine Rating: 1 out of 5Overall Opinion: False advertising. Does NOT fit 2001 Tundra as advertised. One of the stabilizer bushings is undersized. |
 | Front Sway Bar and Endlink Bushings - 24mm - Part Number: 181118 Customer: Juan Gonzalez Rating: 1 out of 5Overall Opinion: The Parts do not Fit in my car, and I can not make the installation... Thanks |
 | Front Sway Bar Bushings - 18mm - Part Number: 181120 Customer: Douglas Low Rating: 5 out of 5Overall Opinion: Very good quality Parts, service as I expected. Thanks. |
 | Front Sway Bar Bushings - 30mm - Part Number: 181121 Customer: jose l. villasana Rating: 5 out of 5Overall Opinion: Josevill17@yahoo.com This part in my car is ready and is very good |
| Front Sway Bar Bushings - 30mm - Part Number: 181121 Customer: Bruce Mitchell Rating: 5 out of 5Overall Opinion: Perfect fit. What a quick and easy job to replace these. Along with rack bushings and lower control arm bushings the steering and handling is tight and solid. Definitely worth the money and a bit of work. |
 | Rear Sway Bar Bushings - 24mm - Part Number: 181122 Customer: Sean French Rating: 5 out of 5Overall Opinion: solid bushings, easy install. More response than OEM and will last the life of the car. Install in less than 5 minutes. |
 | Front Sway Bar Bushings - 28.5mm - Part Number: 181123 Customer: Jakov Jurac Rating: 5 out of 5Overall Opinion: Great product Installed without a problem, increased rigidity in corners. |
| Front Sway Bar Bushings - 28.5mm - Part Number: 181123 Customer: David Ramos Rating: 5 out of 5Overall Opinion: no more front end shaking and or noise.. |
 | Rear Sway Bar Bushings - 14mm - Part Number: 181124 Customer: Carlos E. Vaccaro pty 22157 Rating: 5 out of 5Overall Opinion: great quality good price a little bulky the shipping box since these are hard to break, but its a great product!!! |
| Rear Sway Bar Bushings - 14mm - Part Number: 181124 Customer: Jakov Jurac Rating: 5 out of 5Overall Opinion: Great product Installed without a problem, increased rigidity in corners. |
| Rear Sway Bar Bushings - 14mm - Part Number: 181124 Customer: josh gallardo Rating: 4 out of 5Overall Opinion: good Easy to install. For some reason one bushing didn't come pre-cut to slide over the bar so I had to cut on my own. |
 | Front Sway Bar Bushings - 19mm - Part Number: 181126 Customer: Eduardo N. Sosa Rating: 3 out of 5Overall Opinion: Okay Just a little big for my Mr2, but my mechanic was able to cut them and adjust to the right size. |
 | Rear Sway Bar Bushings - 19mm - Part Number: 181127 Customer: rigo mercado Rating: 5 out of 5Overall Opinion: Great product made a huge difference in how the car handles |
 | Front Sway Bar Bushings - 30mm - Part Number: 181128 Customer: Tuyen(Johnny) Duong Rating: 5 out of 5Overall Opinion: These polyurethane bushings are THE ONLY WAY to go when replacing the oem bushings. Much better road feel, and steering feedback! So if you're shopping around for replacement bushings, I highly suggest these! Especially for the trouble you go through doing it yourself. |
 | Front Strut Rod Bushings - Part Number: 181202 Customer: Rusty Etheridge Rating: 5 out of 5Overall Opinion: highly impressed Stiffened up the whole front end. Turn in is much more solid and predictable. Worth every penny for the enthusiastic driver. |
| Front Strut Rod Bushings - Part Number: 181202 Customer: Matt D Rating: 2 out of 5Overall Opinion: shocked to say the least I have a 2000 toyota tacoma 2wd and i ordered these bushings to replace the original rubber ones i had. The problem was they sent me bushings that were 6xs bigger then they should have been. I have not talked to customer service yet to see if this was a joke or a mix up. I cant see 1 possible place to put these on my truck so im guessing they sent me a monster truck part by accident im not sure yet.... ill have a update shortly. I gave it a 2 because if i owned a monster truck i dont see this breaking anytime soon. |
 | Front Strut Rod Bushings - Part Number: 181203 Customer: WILLIAM MURFITT Rating: 5 out of 5Overall Opinion: Great replacement parts Replacement parts were and exact fit, and restored handling and reduced steering wheel vibration...... |
| Front Strut Rod Bushings - Part Number: 181203 Customer: Aaron Lehtonen Rating: 5 out of 5Overall Opinion: Excellent Product These bushings were excellent and inexpensive. |
 | Front Bump Stops - Part Number: 181301 Customer: Hayden Jarvis Rating: 5 out of 5Overall Opinion: They work These work well. |
 | Front Coil Spring Lift Kit - 2.5 Inch - Part Number: 181701 Customer: Andrey Shmirko Rating: 4 out of 5Overall Opinion: This kit also fit to my Toyota Hilux Surf 3.0 1KZ Turbo Diesel. But I did not install the tie rod dust boot and ball joint dust boot because the original dust boot protects better and does not slip off the parts as fixed wire, which in turn prevents the increase of water. In general I am very pleased with the purchase of this item. |
 | Total Kit - Part Number: 182001 Customer: Mark Guzman Rating: 5 out of 5Overall Opinion: Very very nice this 1979 Toyota Pickup has never driven so nice!! I need to check if you have a set up for my 2000 540i BMW if yes this would be the best of both worlds!!! |
 | Total Kit - Part Number: 182003 Customer: Aaron K Ross Rating: 5 out of 5Overall Opinion: Awesome product Everything fit perfect and was a very high quality material. And the price you can't beat. |
 | Total Kit - Part Number: 182004 Customer: Gary Preston Rating: 5 out of 5Overall Opinion: Nice kit Due to my unusual situation with my Toyota Rv being a C & C with really no way of knowing exactly which are the correct parts Mr. Graham Like The Cracker (Strange last name) was extremely helpful in figuring out the most likely match and when 1 part was the wrong one he was very fast in shipping out the correct part. What more can you ask for in a company. The parts fit perfectly. |
| Total Kit - Part Number: 182004 Customer: Paul B Wong Rating: 5 out of 5Overall Opinion: Prothane Kit for my toyota pickup 1991 2wd. Truck rides like a new truck or better. Some work involve but if you are going to keep your truck or car you got to do it. You can feel the difference. Hey any way see you on the road. |
| Total Kit - Part Number: 182004 Customer: Narcisse D de Palm Rating: 4 out of 5Overall Opinion: Ive been going through a streak of bad days since January 2012 so it didn't amaze me to find obstacles. As you can see its quite some time sins I ordered these parts (Jan 2012) and haven't done much but noticed that the front control arm bushings don't fit. Their outside diameter is 3.6mm and inside 2.5mm. The old ones are 3.9mm outside and 2.9mm inside. The length was fine though. I used a tool to remove the old ones but can slide the new ones in by gravity. I haven't tried the other ones, that's next time. |
 | Total Kit - Part Number: 182008 Customer: donald f hovorka Rating: 5 out of 5Overall Opinion: awsome upgrade! this kit really tightened up my mr2. this is the best bang for the buck upgrade anyone could do. |
| Total Kit - Part Number: 182008 Customer: Emmanuel Le henanff Rating: 4 out of 5Overall Opinion: Very good Hello Installation is easy, but having had bushing "SuperPro" I find that you have a problem, once mounted on the arm , the bushing is wider than the axles, I'm afraid that eventually it will be noisy. |
| Total Kit - Part Number: 182008 Customer: Raymond Person Rating: 5 out of 5Overall Opinion: looked good for price . Well if you need them replaced or upgraded this is the way to go. My mr2 rides great now, tighter and ready for my cheap ebay turbo he he |
| Total Kit - Part Number: 182008 Customer: Anthony Glaser Rating: 5 out of 5Overall Opinion: quality parts, great fitment Quality parts, great fitment. Obvious great upgrade from oem. |
 | Total Kit - Part Number: 182009 Customer: kelly schutt Rating: 5 out of 5Overall Opinion: excellent They shipped the parts promptly .everything described in the description is exactly what I got all the parts were correct with no defects I am very pleased. |
| Total Kit - Part Number: 182009 Customer: Jack Andersen Rating: 5 out of 5Overall Opinion: Nice quality and fit. The Prothane bushings were great to install. The instructions however, were generic at best. All the talk about burning out the old bushings was completely inaccurate. The bushings fit nicely once I realized they were machined to fit directly into the control arms. The video supplied on your web site talking about squeaking problems prompted me to install zerks for future lubrication. Should squeaking occur I will be after your special grease. Thanks for the quality parts at an affordable price. Jack Andeersen |
 | Front Control Arm Bushings - Part Number: 18204 Customer: Jim Windham Rating: 5 out of 5Overall Opinion: Perfect fit and upgrade to overall feel of suspension Best money spent on upgrade |
 | Front Control Arm Bushings - Part Number: 18205 Customer: James Dastrup Rating: 5 out of 5Overall Opinion: easy install worked fine problem solved |
| Front Control Arm Bushings - Part Number: 18205 Customer: Jared Evans Rating: 5 out of 5Overall Opinion: great part, exactly as listed for the application Part fit exactly as described. Would be much easier if more details of install were included, as far as the part goes. |
 | Front Control Arm Bushings - Part Number: 18207 Customer: sean conner Rating: 5 out of 5Overall Opinion: very satisfied The parts are an amazing fix to the problem I was having. The price was better than any others and they fit fairly well. My Lexus rides a lot more smoothly now. The business part of the deal was also one of the most precise and friendly that I have had since being in the automotive industry. Please keep doing what you are doing. |
| Front Control Arm Bushings - Part Number: 18207 Customer: Branden Holt Rating: 5 out of 5Overall Opinion: LOVE THEM!!! These were exact fit and worked awesomely!!! No more popping and I can tell a difference in the handling!! The price was very affordable & the customer service was great! I HIGHLY recommend these bushings to ANYONE! Will be buying from again for any of my suspension needs! Thank you!! |
| Front Control Arm Bushings - Part Number: 18207 Customer: Les Searle Rating: 5 out of 5Overall Opinion: Excellent Great parts, solved the problem with our suspension |
| Front Control Arm Bushings - Part Number: 18207 Customer: Jeff Bullington Rating: 5 out of 5Overall Opinion: Excellent Product, Fast Shipment I had Prothane recommended to me by a friend who is a Lexus mechanic. The parts were for my mothers Lexus. I saved a tremendous amount of money not going with the factory kit, and the Prothane product having a lifetime guarantee seemed the only right way to go. We ordered and received the parts very quickly. Once they were installed the handling of my mother's car changed tremendously. Tighter handling, better steering, and an all around good feel to the car when on the road. I highly recommend if you need suspension parts to go with Prothane! I did, and will again and again should the need arise. |
| Front Control Arm Bushings - Part Number: 18207 Customer: George Hurt, Jr Rating: 5 out of 5Overall Opinion: Outstanding Quality product, easy install. Saved me a ton of money. |
| Front Control Arm Bushings - Part Number: 18207 Customer: Ricky Shigemura Rating: 5 out of 5Overall Opinion: was easy to install and worked as expected. Excellent product. Excellent service and communication. |
| Front Control Arm Bushings - Part Number: 18207 Customer: Jeffrey San Agustin Rating: 5 out of 5Overall Opinion: Perfect fit, awesome price. Thanks |
| Front Control Arm Bushings - Part Number: 18207 Customer: Darryl R. Jackson Rating: 5 out of 5Overall Opinion: Great Part, Super Price! Great customer service and fast shipping! My installer said they installed easily and said they were a perfect fit! My Lexus SC300s steering is tight and more responsive now. Keep up the good work! |
| Front Control Arm Bushings - Part Number: 18207 Customer: Dan Paul Rating: 5 out of 5Overall Opinion: Good quality parts at a great price The bushings arrived quickly and contained enough bushings and grease to do all four front control arms for my 1992 Lexus SC-400. The old bushings had to be burned out and certain parts reused with the new bushings, but this seems to be a common procedure for all of this type of replacement bushings. The job was time consuming, but straight forward. The fit and finish of the parts was first rate, and the instructions adequately detailed the procedure. The price was excellent. I was able to do the complete front of the car at a fraction of the cost of the other guys. I would highly recommend this product to anyone. |
| Front Control Arm Bushings - Part Number: 18207 Customer: Bruce Mitchell Rating: 5 out of 5Overall Opinion: Excellent product. Installed the bushings on the LCA of my 93 SC400. What a difference in control and handling. The fit was perfect and relatively easy to install. |
| Front Control Arm Bushings - Part Number: 18207 Customer: paul kelchner Rating: 5 out of 5Overall Opinion: High Quality And I am sure they will last Long These bushings installed exactly as the instructions said they are extremely tight once put on the car.Probably will outlast the car,and the alignment guy was impressed with how tight the front end was. You cant get a better bushing kit for sc-400 |
 | Front Control Arm Bushings - Part Number: 18210 Customer: Spencer D Hanks Rating: 5 out of 5Overall Opinion: Great Product I found these easy to install and was surprised that they have some give to them unlike many polyurethane parts these give the feel of rubber with the durability of poly. |
 | Rear Control Arm Bushings - Part Number: 18304 Customer: Larry Pecchia Rating: 5 out of 5Overall Opinion: Order was completed & shipped in record time. So far so good on product installation. Would & have used Energy Suspension again. Also would recommend to others |
 | Steering Rack Bushings - 4WD - Part Number: 18701 Customer: Dennis Skiles Rating: 5 out of 5Overall Opinion: Very well made and priced right My 96 Tacoma had about 1 inch play side to side on the steering wheel before I installed the bushings. Now there is no play what so ever. The truck handles like a sports car. I also like the feed-back I feel in the wheel now. Should have done this long ago. |
| Steering Rack Bushings - 4WD - Part Number: 18701 Customer: Alberto Cohen Rating: 5 out of 5Overall Opinion: These were ok These parts were good for my car |
 | Steering Rack Bushings - Manual Steering - Part Number: 18702 Customer: assassin10000 Rating: 5 out of 5Overall Opinion: Great Replaced stock rubber bushings on my manual rack swapped AE86, much better! |
 | Rear Frame Shackle Bushing Kit - Part Number: 18803 Customer: cole contois Rating: 5 out of 5Overall Opinion: Okay I really wish these bushings were set up to accept a regular bolt and not the original sleeved bolt. Now I am hunting for bolts with a sleeve through them. |
 | Universal Sway Bar Bushings - 11/16 Inch - A - Part Number: 191105 Customer: jon pellegrini Rating: 5 out of 5Overall Opinion: Very good product Sway bar bushings were easy to install. A tube of grease was also included, to help keep them from squeaking. |
 | Universal Sway Bar Bushings - 1 Inch - A - Part Number: 191110 Customer: Stephanie McCallum Rating: 5 out of 5Overall Opinion: good These replacement parts worked just fine and fit just as well the originals did. |
 | Rear Sway Bar Bushings - 17mm - Part Number: 191116 Customer: John Rong Rating: 5 out of 5Overall Opinion: Excellent product Wasn't sure how I was going to get them spread far enough to go over the sway arm so I let them sit in some really hot water for a couple of minutes and everything went smooth. The wife is so happy that there is no longer a noise in the rear of her Toyota. And you know what they say, If momma ain't happy, ain't nobody happy. Do you have any catalogs for your suspension parts, especially stuff for old iron? Have a couple on the burner waiting for attention. John C Rong 4900 NW Piekenbrock Drive Des Moines, IA 50310 Thanks, John |
 | Rear Sway Bar Bushings - 19mm - Part Number: 191118 Customer: Timothy Parchman Rating: 5 out of 5Overall Opinion: Didnt fit A mis-judgement on my part. On the Impala, there is a small, metal shelf where the bushings go. The stocks are made to fit there. These were not. So I couldn't install them. But I rate a 5 just for how tough they felt. |
| Rear Sway Bar Bushings - 19mm - Part Number: 191118 Customer: louis becker Rating: 5 out of 5Overall Opinion: I bought the complete PST front end set from this guy on ebay. It works very well on my 72 roadrunner. I also rebuilt the rear sway bar with assorted parts from your universal section. All parts worked well and fit correctly. I am looking forward to future driving experiences. Thanks |
| Rear Sway Bar Bushings - 19mm - Part Number: 191118 Customer: Mark c Bullett Rating: 5 out of 5Overall Opinion: Excellent Great quality, good shipping time. I like the fact that the brackets are slotted. I used mine on a different car/application and the slots worked nicely. Thanks, MB |
 | Universal Sway Bar Bushings - 20mm - A - Part Number: 191119 Customer: Alfred Laussegger Rating: 5 out of 5Overall Opinion: Great!!! These parts are doing their job (what else should I say from a pair of bushings?). But what I need to say, is the outstanding customer service from energysuspensionparts.com. Even on this small business (2 pairs of Sway Bar Bushings) they mailed back two times and took an extra afford in cheap shipping. A big recommendation from me for this service - if I ever will need suspension parts in future, energysuspensionparts will be my first choice! |
| Universal Sway Bar Bushings - 20mm - A - Part Number: 191119 Customer: Jeffrey Millikan Rating: 5 out of 5Overall Opinion: excellent product. I use energy suspension products on all of my custom suspensions. |
| Universal Sway Bar Bushings - 20mm - A - Part Number: 191119 Customer: John Hall Rating: 5 out of 5Overall Opinion: Excellent!! Excellent high quality product. High recommend. I look forward to years of trouble free use as always from energy suspension products. Thanks! |
 | Front Sway Bar Bushings - 21mm - Part Number: 191120 Customer: Ben Reardon Rating: 5 out of 5Overall Opinion: Good part Had to buy new bolts to mount. Rides smooth and better than stock. |
| Front Sway Bar Bushings - 21mm - Part Number: 191120 Customer: carsthen wiig Rating: 5 out of 5Overall Opinion: good Nice and good upgrade, also cheap :) |
 | Front Sway Bar Bushings - 22mm - Part Number: 191121 Customer: Angel Garcia Rating: 4 out of 5Overall Opinion: Okay These bushings even though they work fine we have a problem with squeaking. |
 | Universal Sway Bar Bushings - 11/16 Inch - B - Part Number: 191129 Customer: Off The Wall Rating: 5 out of 5Overall Opinion: Good quality I haven't had an opportunity to do anything other than a mock-up yet, but thus far, they are a perfect fit for my custom application.(11/16 Inch front sway bar on a 57 Nash Metropolitan) Great customer service and fast shipping as well. You've got a customer for life. |
 | Universal Sway Bar Bushings - 3/4 Inch - B - Part Number: 191130 Customer: Johnny Glover Rating: 5 out of 5Overall Opinion: discoun5tbrother@yahoo.com This is the best product. Works great for my Cadillac. I will always purchase from Energy Suspension. All there items are 100% better then O.E. and last longer. Works better. I had to purchase lower control arm bushings, no auto shop could help me with the right parts. So I went online and found Energysuspensionparts.com and we have a lot of cars and trucks in my family and I do all auto repairs on them. Will be using this website very soon. Thank you guys. From Lacville 94 |
 | Universal Sway Bar Bushings - 7/8 Inch - B - Part Number: 191132 Customer: scott atwell Rating: 5 out of 5Overall Opinion: very nice The bushings fit very well. Both the bolt pattern and the diameter for the sway bar bushing itself. The red colored bushings add some nice contrast to the other new parts I've added. I mistakenly ordered two pairs. A buddy of mine has a 72 Chevelle. He asked if he could have the other pair. Now were both happy. |
 | Universal Sway Bar Bushings - 1-1/16 Inch - B - Part Number: 191135 Customer: Jeffry Mooney Rating: 5 out of 5Overall Opinion: Love them Fit right up and I can hardly wait to drive the GMC without all the "thunder under"... |
 | Universal Sway Bar Bushings - 1-1/8 Inch - B - Part Number: 191136 Customer: don miller Rating: 5 out of 5Overall Opinion: GOOD THESE WERE GOOD BUT YOU SENT THE WRONG SIZE, HOLE W IS MUCH TOO LARGE. I MEASURED WITH A CALIPER AND ORDERED, HOLES ARE LARGER |
| Universal Sway Bar Bushings - 1-1/8 Inch - B - Part Number: 191136 Customer: John Traugot Rating: 5 out of 5Overall Opinion: Great product Arrived very quickly. I was a little nervous about ordering this cause Chevy used so many sizes, but i ordered the right one and everything fit perfectly. Felt a big difference in handling right away. |
 | Universal Sway Bar Bushings - 25mm - B - Part Number: 191141 Customer: EDWARD KALEDA Rating: 5 out of 5Overall Opinion: Excellent Quality Installed these on my 2007 HHR LT2 with a 25mm bar. They work great in eliminating the thump when going over small bumps. When installing make sure you center the bar before tightening. |
| Universal Sway Bar Bushings - 25mm - B - Part Number: 191141 Customer: Keith Scala Rating: 5 out of 5Overall Opinion: Good replacement part Installed easy and was the right part, took a while to figure out which universal bushing to order. My car a Mazdaspeed 6 had no direct listings. I used this part for the front sway bar mounts. |
| Universal Sway Bar Bushings - 25mm - B - Part Number: 191141 Customer: Lee Doran Rating: 5 out of 5Overall Opinion: Good Installed on my 2007 Chevy HHR. Worked great. No more front end clunk. This is the part you need to replace to get rid of that pothole clunk sound in the front end. Seems like it even tightened up the steering. |
| Universal Sway Bar Bushings - 25mm - B - Part Number: 191141 Customer: richard macgregor Rating: 5 out of 5Overall Opinion: super These are universal bushings. I was worried that they would not fit our 09 HHR Chevy but they did. You must do your homework to determine the width of your application and if you measure well......you are golden. Our car had an odd suspension clunk from rubber, worn bushings, no more! RM |
 | Universal Sway Bar Bushings - 26mm - B - Part Number: 191142 Customer: Jon Rating: 5 out of 5Overall Opinion: Great improvement on Mazdaspeed3 The OEM bushings on the front sway bar of my 2007 Mazdaspeed3 started to go around 40,000. By 60,000 the clunk at low speeds over bumps was pretty bad. Since I installed these the car is silent and handling seems to have tightened up a bit as well. Thanks! |
| Universal Sway Bar Bushings - 26mm - B - Part Number: 191142 Customer: Krzysztof Wrzosek Rating: 5 out of 5Overall Opinion: Great product Quick delivery and great quality. Made big change in handling :) |
| Universal Sway Bar Bushings - 26mm - B - Part Number: 191142 Customer: Timothy Tardiff Rating: 5 out of 5Overall Opinion: The reward is worth the effort. I have a Mazdaspeed 3. The only dimension on these parts that match the original part is the I.D. of the hole at 26mm. The rest are all about 1/3 larger. The material is stiffer than stock by a lot. The rings around the stock sway bar are so close to the bolt holes that the new brackets have to be modified with a slot in the side. Washers have to be used to make up for the small bolt head. This job is not easy, but when complete, the car drives like never before. They are quiet and strong. |
| Universal Sway Bar Bushings - 26mm - B - Part Number: 191142 Customer: William Erikson Rating: 5 out of 5Overall Opinion: Fine. Does the job. I had to slide the rings on my MS3s front swaybar a bit inwards to allow for the increased width of these over stock, but that was easily done with a prybar. Overall, they work fine and are cheap! No problems, solved my clunking issue. |
 | Universal Sway Bar Bushings - 28mm - B - Part Number: 191144 Customer: Brian Rating: 5 out of 5Overall Opinion: Parts look good and work fine. Easy to install and fit perfect |
 | Universal Sway Bar Bushings - 30mm - B - Part Number: 191146 Customer: Herman Snoddy Rating: 5 out of 5Overall Opinion: Exellent Parts worked perfectly |
| Universal Sway Bar Bushings - 30mm - B - Part Number: 191146 Customer: Ben Reardon Rating: 5 out of 5Overall Opinion: Good Part I had to buy new mounting bolts but I love these bushings, much improved over stock ride. |
 | Universal Sway Bar Bushings - 32mm - B - Part Number: 191148 Customer: Austin Rating: 5 out of 5Overall Opinion: Great product I ordered these to use with a new front swaybar on my Honda S2000. The bar I am using is 1-5/16" diameter, and tapers down to 1.25" at the end. The bushings would have fit perfectly if they mounted to the bar at the end, but because they mounted about 6 inches from the end of the bar, I had to do a little bending of the metal bracket, and some minor trimming of the actual urethane (but that was only cosmetic cutting on the edge so it would fit a little better on the stock bracket). Im very pleased with this product, and I'm very happy with the price. Other brands were wanting almost $125 for these things, glad there is an alternative for us lower budgeted racers! Thanks Prothane, Ive bought from you before, and I will continue to buy from you in the future! |
| Universal Sway Bar Bushings - 32mm - B - Part Number: 191148 Customer: bernard obryant Rating: 5 out of 5Overall Opinion: these bushings are superior! Easy installation and great feel in ride too! |
 | Greaseable Sway Bar Bushings - 11/16 Inch - A - Part Number: 191153 Customer: William Hunter Rating: 5 out of 5Overall Opinion: well suited for the job Fitment was like factory with an attitude |
 | Greaseable Sway Bar Bushings - 7/8 Inch - A - Part Number: 191156 Customer: scott hendricks Rating: 5 out of 5Overall Opinion: great replacment part Put on sway bar of a 08 kawi 650i brute. Love them, handles 100% better |
 | Greaseable Sway Bar Bushings - 1 Inch - A - Part Number: 191158 Customer: Larry Grimes Rating: 5 out of 5Overall Opinion: Fast shipping and a very good product The parts installed easily and fit nicely. Very satisfied and pleased with the product. |
 | Greaseable Sway Bar Bushings - 17MM - A - Part Number: 191160 Customer: ilya visgordinskiy Rating: 5 out of 5Overall Opinion: Very Happy with Quality and ease of installation The installation went very fast. The bushings are made with high quality. Ample reliefs within the bushing allow the grease to flow through the bushing and not get caught up in a crevice. However looking at the design and amount of reliefs provided within the bushing for the ability to grease externally it is obvious that they should be greased very frequently to avoid bushing destruction from excessive forces. |
| Greaseable Sway Bar Bushings - 17MM - A - Part Number: 191160 Customer: Seth Elliott Rating: 5 out of 5Overall Opinion: Great product They work great. |
 | Greaseable Sway Bar Bushings - 19MM - A - Part Number: 191162 Customer: BEN RODRIGUEZ Rating: 5 out of 5Overall Opinion: I HIGHLY RECOMMEND THEM !! PARTS ARRIVED AND WERE INSTALLED THE VERY NEXT MORNING. I WAS DYING TO INSTALL THEM; WHAT A DIFFERENCE IN THE REAR HANDLING OF MY 2002 PONTIAC FIREBIRD. THANKS A BUNCH FOR ALL YOUR TIME AND EFFORT FOR SUCH A SMALL ORDER. WHAT A SHAME THAT YOU DON'T HANDLE DIFFERENT PARTS FOR MY CAR, CAUSE YOUR SERVICE IS AWESOME. YOUR COMPANY WAS ALWAYS BEHIND THE ORDER ALL THE TIME, VIA EMAIL or PHONE CALLS [THE PART WAS IN B/O] AND TOOK A LITTLE TO ARRIVE. VERY, VERY PLEASED. THANKS AGAIN. Ben RODRIGUEZ. MIAMI, FL. |
| Greaseable Sway Bar Bushings - 19MM - A - Part Number: 191162 Customer: Brandon Moorhouse Rating: 5 out of 5Overall Opinion: wonderful product The aftermarket sway bars didn't come with new bushings, and wouldn't fit in the factory ones. These bushings fit the bars perfectly, bolted right up to my car. No problems at all. Great product with a great price too. Thanks energy suspension |
| Greaseable Sway Bar Bushings - 19MM - A - Part Number: 191162 Customer: Scott Saunders Rating: 5 out of 5Overall Opinion: great product These bushings fit just like the fronts did, like a glove. Just had to drill a tap some broken bolts (my 4 runner has 152,000 New England miles) These are almost too easy to install. Top notch shipping - 3 days. |
 | Greaseable Sway Bar Bushings - 20MM - A - Part Number: 191163 Customer: Anthony Bush Rating: 5 out of 5Overall Opinion: Hi, the illustration is confusing. These are 1 5/16 tall and 1 1/4 wide. I thought they were 1 5/16 wide so they did not work. Thanks, anthony |
 | Greaseable Sway Bar Bushings - 21MM - A - Part Number: 191164 Customer: Brandon Moorhouse Rating: 5 out of 5Overall Opinion: great replacement The aftermarket sway bars didn't come with new bushings, and wouldn't fit in the factory ones. These bushings fit the bars perfectly, bolted right up to my car. No problems at all. They even have a great price. Glad I found these. |
| Greaseable Sway Bar Bushings - 21MM - A - Part Number: 191164 Customer: Bill Glauner Rating: 5 out of 5Overall Opinion: Excellent Product! I switched over to energy suspension bushings for my aftermarket sway bars in my 2005 Subaru Legacy GT. These bushings were the only ones in this size that came with grease fittings which make these really easy to grease and maintain. They also perform really well. I would highly recommend them. |
| Greaseable Sway Bar Bushings - 21MM - A - Part Number: 191164 Customer: mitchell Rating: 5 out of 5Overall Opinion: good quality, great price thanks |
 | Greaseable Sway Bar Bushings - 22MM - A - Part Number: 191165 Customer: eugene tucker Rating: 5 out of 5Overall Opinion: GREAT! Used these to mount an Integra Type R rear sway bar on a 1998 honda civic using an ASR subframe brace and endlinks to Skunk2 lower control arms. Be sure to grease the insides of the bushings and outside before you install with non petroleum lubricant. Great product and love the included zerks :) |
| Greaseable Sway Bar Bushings - 22MM - A - Part Number: 191165 Customer: thomas klein Rating: 5 out of 5Overall Opinion: Great product Perfect fit for Perrin rear sway bar on my 03 WRX! |
| Greaseable Sway Bar Bushings - 22MM - A - Part Number: 191165 Customer: Jean-Luc Robert Rating: 5 out of 5Overall Opinion: Perfect fit, well built Fit perfectly for my 22mm rear sway bar (progress) on my 2004 Acura TSX. |
| Greaseable Sway Bar Bushings - 22MM - A - Part Number: 191165 Customer: Jeffrey Janzer Rating: 5 out of 5Overall Opinion: Good. A neat and tidy bushing, perfect for the application intended. The well made compact design allowed these to fit and function where others could not. Coupled with good, fast, customer service, made this interweb buying experience an uncommon pleasure. Ill be back for more. |
 | Greaseable Sway Bar Bushings - 24MM - A - Part Number: 191167 Customer: Tommy Guttmann Rating: 5 out of 5Overall Opinion: Very nice piece and good value What I also liked is that this and the 191168 I later ordered are available as greasable versions despite the small bolt spread!! Also, the urethane was sized properly, not requiring sanding down the base to avoid clamping the sway bar too tightly and binding |
 | Greaseable Sway Bar Bushings - 25MM - A - Part Number: 191168 Customer: tim gardner Rating: 5 out of 5Overall Opinion: Great inexpensive suspension upgrade I installed the Prothane sway bar bushings on my 99 Rav4 and they made the handling much tighter in the corners compared to my older stock rubber bushings. It's a great upgrade for not a lot of money. If your doing it for the first time be sure to remove one of your old bushings in order to get an exact measurement of the bushing and bracket before ordering the new ones as there are a variety of shapes and sizes to choose from. |
| Greaseable Sway Bar Bushings - 25MM - A - Part Number: 191168 Customer: Curtis Baker Rating: 5 out of 5Overall Opinion: perfect fit no issues |
 | Greaseable Sway Bar Bushings - 1 Inch - B - Part Number: 191177 Customer: Jerry Bahr Rating: 5 out of 5Overall Opinion: Super. Quality Awesome product, really tightened up the front end. Very happy with purchase would recommend to anyone. |
 | Greaseable Sway Bar Bushings - 1-1/8 Inch - B - Part Number: 191178 Customer: mike mondello Rating: 5 out of 5Overall Opinion: better then GM part top flight It's not always true that after market parts are better then OE, however, Prothane Sway Bar Bushings are light years better. IRON HEAD N.Y. |
 | Greaseable Sway Bar Bushings - 1-1/4 Inch - B - Part Number: 191179 Customer: Gloria Brown Rating: 5 out of 5Overall Opinion: Great product Great product and great price. Exactly what i needed and shipping was fast. |
 | Greaseable Sway Bar Bushings - 26MM - B - Part Number: 191182 Customer: Todd Verrone Rating: 5 out of 5Overall Opinion: Work perfectly, a great, easy upgrade Once i figured out the exact position to mount these in, they have been a perfect upgrade. They stiffen up the suspension greatly. I'm now sliding the rear end through corners because of how stable these make the car. Before I had to slow down so much for most corners due to body roll that I never approached the speeds needed for the back to slide out. I am surprised at what a difference these made. |
| Greaseable Sway Bar Bushings - 26MM - B - Part Number: 191182 Customer: simon logan Rating: 5 out of 5Overall Opinion: good item This part does not fit the 2002 dodge caravan sebut, after small modifying the bracket it should fit, but the product is very good plus it is greaseable. Buy it |
| Greaseable Sway Bar Bushings - 26MM - B - Part Number: 191182 Customer: gregory horine Rating: 5 out of 5Overall Opinion: good These bushings replaced the worn rear swaybar bushings on my 2008 mazdaspeed 3. The bushings work great, no more clunk when going over bumps and potholes, at least from the rear of the car. The only problem was with installation. The new bushings are wider then the originals. As a result I had to cut off the original collars and install new custom collars, which I actually like better. I plan to install new bushings this fall on the front swaybar. |
| Greaseable Sway Bar Bushings - 26MM - B - Part Number: 191182 Customer: Robert Smith Rating: 5 out of 5Overall Opinion: Good quaility! I started out by installing the rear swaybar bushings on my 2008 Mazdaspeed3. Fit and finish was fantastic! Far superior to the OEM bushings and have grease fittings. Fantastic! I went to install the front swaybar bushings and ran into some problem: the holes DO NOT line up. Honestly do wish they did line up. The rear bushings are highly recommended! |
| Greaseable Sway Bar Bushings - 26MM - B - Part Number: 191182 Customer: Randy C Rating: 5 out of 5Overall Opinion: Skeptical At First I purchased these bushings to replace the ones on my Mazdaspeed 3. At first I thought they would not perform as I was expecting. Boy was I wrong. I had to make a slight modification because these bushing are bigger than the stock ones. Once installed I noticed a huge difference in performance. My Mazdaspeed handles so much better than before. It is very noticeable. I would definitely purchase these again. |
| Greaseable Sway Bar Bushings - 26MM - B - Part Number: 191182 Customer: Renjith Chandrasekharan Rating: 5 out of 5Overall Opinion: Great combo. Used them on my 07 Mazdaspeed3, with about 118K on clock. They bush-bracket combo fit perfectly. Very impressed overall. Very impressed overall |
| Greaseable Sway Bar Bushings - 26MM - B - Part Number: 191182 Customer: Scott Saunders Rating: 5 out of 5Overall Opinion: great product! The Prothane greasable bushings fit like a glove on my 99 4 Runner. The hardest part is getting the old ones off. Die grinder and sawmill and that was it. My parts were at my door in 3 days. Thanks Graham! |
 | Greaseable Sway Bar Bushings - 27MM - B - Part Number: 191183 Customer: Bee Thao Rating: 5 out of 5Overall Opinion: HAHAhahaha The bushings are great and I'm not surprised if these bushings are supplied to many companies. Fits perfect and would recommend to people. However, I'm not too sure about the metal part though. With my past experiences, screws and bolts that have that color or finish tend to rust. Maybe aluminized coating would do great. I rubber coated my metal pieces. |
 | Greaseable Sway Bar Bushings - 29MM - B - Part Number: 191185 Customer: lukasz stapor Rating: 5 out of 5Overall Opinion: Great bushing As a replacement bushing this is exactly what I needed. It fits like a glove. Perfect fit. It got rid of any rattling sounds coming from the sway bar. And the price is unbeatable. Great costumer service and fast shipping. I will be using Energy Suspension parts any time I need a replacement. |
| Greaseable Sway Bar Bushings - 29MM - B - Part Number: 191185 Customer: Andrew Gale Rating: 5 out of 5Overall Opinion: Just what I needed My front BMR sway was creaking bad, so I replaced them with these bushings. Didn't use the brackets as BMR said theirs are custom. They suggested green grease as the polys tend to be loud. Very happy. |
 | Greaseable Sway Bar Bushings - 30MM - B - Part Number: 191186 Customer: John Moore Rating: 5 out of 5Overall Opinion: Very Good This will work on my Dodge 2007, 2x4 2500. Thanks, John Moore |
| Greaseable Sway Bar Bushings - 30MM - B - Part Number: 191186 Customer: Alex Rating: 5 out of 5Overall Opinion: Better than stock. Put these on my 05 Tacoma 2wd about a month ago. Replacing the worn out stock bushings solved some front end squeaks and creaks I had been experiencing. Installation was a little tricky since these are universal bushings. They are slightly wider than my stock bushings, so getting the sway bar back in the correct position took some persuasion. I do like the grease fittings and hopefully these will last the rest of the life of my truck. |
 | Greaseable Sway Bar Bushings - 31MM - B - Part Number: 191187 Customer: William Fagan Rating: 5 out of 5Overall Opinion: Better than OEM My 2002 Explorer gets the undercarriage wet pretty often offroad. I bet the sway bar squeaks about every 5 months. It is really tough to keep removing the old bushings and greasing them. I thought these replacements would be perfect. Not quite- I still have to loosen them up or the grease will not flow into the bushing ID. It is still a lot easier and turns a 1hr job into a 15 minute job. 90 degree fittings would have been better too, in my opinion. |
 | Greaseable Sway Bar Bushings - 32MM - B - Part Number: 191188 Customer: Anthony Rhoden Rating: 5 out of 5Overall Opinion: Excellent product. I bought these to replace the brackets and bushings on an aftermarket rear sway bar for a 2008 Mazdaspeed 3. The brackets that came with the bar originally did not have the zerk fittings nor did the bushings have the grease grooves. It led to heavy squeaking and creaking as the grease would continually get pushed out of the bushing over time. Without the zerk fittings, re-greasing was quite a chore. These new brackets and bushings have taken care of everything. No more squeaking or creaking and they seem to be holding up well to my spirited driving habits. Initial impression of the parts on arrival was very good. Great quality materials and very sturdy construction. Overall, I couldn't be happier. |
 | Greaseable Sway Bar Bushings - 1-1/16 Inch - B - Part Number: 191189 Customer: Philip Day Rating: 5 out of 5Overall Opinion: No problems ... install fine Nice to have grease fittings & makes a BIG improvement with new end links, over stock rubber ones. Like putting on a larger dia. bar. |
 | Front Lower Control Arm Bump Stops - Part Number: 191303 Customer: William Card Rating: 5 out of 5Overall Opinion: nice Nice Upgrade. Easy to install. |
| Front Lower Control Arm Bump Stops - Part Number: 191303 Customer: Rogelio Medina Rating: 5 out of 5Overall Opinion: Good product Good product, right size, fits perfect. |
 | Progressive Rate Multi Mount Bump Stop - 2 Inch - Part Number: 191306 Customer: redrum03 Rating: 5 out of 5Overall Opinion: Excellent Bought as replacement bump stops after I lowered my truck. These work great and are of much better quality than similar products I looked at. |
| Progressive Rate Multi Mount Bump Stop - 2 Inch - Part Number: 191306 Customer: Doug Matthews Rating: 5 out of 5Overall Opinion: Great product Building a custom truck and need a specific size. They fit great. |
| Progressive Rate Multi Mount Bump Stop - 2 Inch - Part Number: 191306 Customer: Christopher Bodner Rating: 5 out of 5Overall Opinion: Great product had it out on 3 runs no problems. I have broken other bump stops almost immediately on my first run. |
| Progressive Rate Multi Mount Bump Stop - 2 Inch - Part Number: 191306 Customer: Doug Hampton Rating: 2 out of 5Overall Opinion: Unfortunatly, both are alreadyed in two weeks. I basically gave them a beating, I pre ran Baja... so mostly, my fault, although I think the design could use some improvement. theyed in the same place the last ones did. I will be ordering more though. More than happy to give you more info. thanks, Doug Hampton |
 | Progressive Rate Multi Mount Bump Stop - 2.5 Inch - Part Number: 191307 Customer: Vincent M DeWitt jr Rating: 5 out of 5Overall Opinion: great quality parts I replaced the stock bump stops on my 2006 GMC 1500 pickup. I removed the original front bumpstops and welded these in their place. I also lifted the front with aftermarket torsion bar keys. This install leveled the truck and improved the handling and ride comfort. |
| Progressive Rate Multi Mount Bump Stop - 2.5 Inch - Part Number: 191307 Customer: Virgil Zunker Rating: 5 out of 5Overall Opinion: Great parts Needed the parts for fit up on my frame. Will be a while before putting on the road, but these are a quality part that will do the jog of stopping the rear axle housing when and if needed. |
| Progressive Rate Multi Mount Bump Stop - 2.5 Inch - Part Number: 191307 Customer: Christopher L. Martin Rating: 5 out of 5Overall Opinion: Very Good Service was great! Item was used to replace missing OEM parts on a 1998 Dodge Dakota. Vastly superior items to stock. Install went smoothly along with new high performance shocks all around. Truck handles better. |
| Progressive Rate Multi Mount Bump Stop - 2.5 Inch - Part Number: 191307 Customer: g baylis Rating: 5 out of 5Overall Opinion: Good product great service |
 | Progressive Rate Multi Mount Bump Stop - 3 Inch - Part Number: 191308 Customer: Stephen J Hobbs Rating: 4 out of 5Overall Opinion: Good These bump stops seem good and solid. The hole location did not fit my Dodge truck but you cannot expect everything from a universal part. With a little file and drill work they are in operation. |
| Progressive Rate Multi Mount Bump Stop - 3 Inch - Part Number: 191308 Customer: AHMAD AZZOUZ Rating: 5 out of 5Overall Opinion: Good customer service and Grade A parts I used these to stabilize my 2002 Camaro during drag racing extreme take off- wonderful. The hi-quality Prothane part is taking the abuse daily without fail. |
| Progressive Rate Multi Mount Bump Stop - 3 Inch - Part Number: 191308 Customer: John Perry Rating: 5 out of 5Overall Opinion: Great product and service Quick delivery and I received exactly what I ordered. |
| Progressive Rate Multi Mount Bump Stop - 3 Inch - Part Number: 191308 Customer: charles lategano Rating: 4 out of 5Overall Opinion: High quality part but not the correct size for a Nissan Quest. The hole centers on a 1999 Nissan Quest are 6.25" apart. The maximum spacing on this part is 6.25". I cut the opening wider and used an oversize galvanized washer on the bolt. I've had them installed for several thousand miles and have no issues. I live 1 mile down a dirt road over a railroad crossing and bottom out regularly. My OEM stops were worn out. These are an excellent replacement. The job would have taken half as long if they were offered with a wider bolt spacing. |
| Progressive Rate Multi Mount Bump Stop - 3 Inch - Part Number: 191308 Customer: Craig Hill Rating: 5 out of 5Overall Opinion: I'm very pleased with the bump stops. I have load tested them several times since installing and they are holding up fine. If I ever need to replace them I'll go back with the same... |
 | Progressive Rate Multi Mount Bump Stop - 3.5 Inch - Part Number: 191309 Customer: Randal Rothlisberger Rating: 5 out of 5Overall Opinion: Quality part Was a little concerned before part arrived, noticed did not state "pair" of bumpers on description. Would have been high priced for one. Did get pair, had to modify slightly to fit my application (slot mounting holes) Seemed to soften the shock of frequent bottoming of my suspension, the effect I was hoping for. Looks sturdier than stock part, so hope it lasts a long time. |
 | Progressive Rate Multi Mount Bump Stop - 4 Inch - Part Number: 191310 Customer: C. Wayne Powell Rating: 5 out of 5Overall Opinion: Excellent product and design supported the adaption to the 1955 chassis. The product was of quality materials and design. I retrofitted the bump stops to a 1955 Olds 98 with air ride suspension. With the slotted design of the mounting plate, the installation was painless and the stops are working well. Supplier was very responsive to questions on tech call prior to purchase and delivery was quick. |
 | Progressive Rate Multi Mount Bump Stop - 4.5 Inch - Part Number: 191311 Customer: brent hansen Rating: 5 out of 5Overall Opinion: nicely made Did not work for my application but that's not Energy's fault. |
| Progressive Rate Multi Mount Bump Stop - 4.5 Inch - Part Number: 191311 Customer: Allen Sarkozy Rating: 5 out of 5Overall Opinion: Good quality product, had to modify to fit, my decision These Urethane bump stops are working very well, I ordered a taller one than OE, but cut them down for load capacity and an even softer ride. The OE were hard rock rubber and these are a bit more forgiving, handling has improved and I don't have the solid bottoming out as before. |
| Progressive Rate Multi Mount Bump Stop - 4.5 Inch - Part Number: 191311 Customer: Chris Bardwell Rating: 5 out of 5Overall Opinion: Great Quality Low Price Perfect for my modified 4X4, Works great. |
 | Front Upper Control Arm Bump Stops - Part Number: 191312 Customer: Jason Kelly Rating: 5 out of 5Overall Opinion: Perfect! With new ceramic headers, old stops and 14" wheels, header strike was becoming an issue. So... now with new stops and "going up one" to 255/60/15s it is no longer a problem. "CODE 3" LAPD Matador. Overspec. |
| Front Upper Control Arm Bump Stops - Part Number: 191312 Customer: ERNEST MCCAIN Rating: 5 out of 5Overall Opinion: good part very nice part at a very reasonable price. They look good and installed good. Once again a great price and Ill definitely buy further parts from them. |
 | Bump Stops - 19-1317 - Part Number: 191317 Customer: Paul A Hoffman Rating: 5 out of 5Overall Opinion: Worked quite well I used these to replace the factory stops on my 2002 Toyota Tacoma and they worked just fine without any problems. |
| Bump Stops - 19-1317 - Part Number: 191317 Customer: Tim Heathcoat Rating: 5 out of 5Overall Opinion: These stops work great and give a linear stop. They give enough to not cause a jarring at the end of suspension movement. |
| Front Upper Bump Stops - Part Number: 191317_FrontUpper Customer: Greg Hausler Rating: 5 out of 5Overall Opinion: excellent Installation was a snap. Not sure about the wear characteristics but material appears to be very durable. |
 | Bump Stops - 19-1319 - Part Number: 191319 Customer: shaun murphy Rating: 5 out of 5Overall Opinion: not good these parts don't live up to what there suppose to do. |
 | Bump Stops - Pull Through - 19-1325 - Part Number: 191325 Customer: christopher spratt Rating: 4 out of 5Overall Opinion: good The upper bumpstops were a royal pain to install. Best technique involves trimming the upper edges of the cross piece shoulders with a very sharp chisel, applying prothane bushing grease to the newly trimmed shoulders, inserting them into the slots and lowering the suspension to compress them in place. Then, using mole-grips, pull them through(may need to lever them). Don't give up, they will go in eventually, and they look great and work well. |
 | Jackpad - Fits Up To 3 Inch Diameter - Part Number: 191403 Customer: Albert Norris Rating: 5 out of 5Overall Opinion: A bit larger in diameter than the lifting point of my floor jack, regardless it provides a non-metallic cushion between the jack and lifting point of the car. |
 | Jack Grabber for High-Lift Jack - Part Number: 191404 Customer: Reggie Anglin Rating: 5 out of 5Overall Opinion: It gives me something i can actually get my paw on. Its a big chunk of material. I like that. No messing around and taking short cuts. Buying it was easy enough. Click, click, ship. I recommended it to my buddies |
 | Jack Pad 5 Inch Diameter - Part Number: 191405 Customer: Mark Licas Rating: 5 out of 5Overall Opinion: Great Quality! Perfectly fits over the saddle and does a great job protecting it. |
| Jack Pad 5 Inch Diameter - Part Number: 191405 Customer: Thomas Marson Rating: 5 out of 5Overall Opinion: Installed it on my 3 ton floor jack lift pad. Works great...and protects the surfaces in contact. I like it. Easily installed on my 3 ton floor jack, works great, and protects the contact surface. Highly recommended. I also have Prothane products for my jack stands. They also work great. |
 | Jack Stand Pads - 2.5 X 4.5 Inch Heads - Part Number: 191411 Customer: Albert Norris Rating: 5 out of 5Overall Opinion: A bit larger (length & width) than the cradle of the jack stands I have, regardless they provide a non-metallic cushion between the jack stand and the lift points of the car. |
 | Jack Stand Pads - 1.5 X 4.5 Inch Heads - Part Number: 191412 Customer: Mark Licas Rating: 5 out of 5Overall Opinion: Good idea If jack saddles can have pads why not jack stands? Great for protecting the chassis. |
 | Tie Rod Dust Boots - Part Number: 191711 Customer: Joseph Ilarraza Rating: 5 out of 5Overall Opinion: Very easy to install. Very effective as well. Have had them on my car for 2-3 weeks and I've checked periodically and they are holding up perfect. Way better solution than buying a new tie rod end. |
 | Tie Rod Dust Boots - Part Number: 191712 Customer: Gregory Lentz Rating: 5 out of 5Overall Opinion: The parts fitt perfect. I had removed the worn out boots and these went on perfectly, no problems at all. Thank You |
| Tie Rod Dust Boots - Part Number: 191712 Customer: CONSTANTINO SANCHEZ Rating: 5 out of 5Overall Opinion: Great product Thanks for the fast on shipping. Strongly recommended and installed in my Jeep Cherokee ZJ 5.2 v8. Attention, speed, quality all OK. |
| Tie Rod Dust Boots - Part Number: 191712 Customer: patrick van der Mooren Rating: 5 out of 5Overall Opinion: Easy and perfect fitting!! Easy to install! Easy and quick to assemble, fits even better!! Glad I had order these parts. Fast and accurate description. À+++++++ |
| Tie Rod Dust Boots - Part Number: 191712 Customer: Gary Replogle Rating: 5 out of 5Overall Opinion: I have installed my parts and I'm very pleased. The service was great and shipping was quick. Parts are made of great quality I will use Energy Suspension again. |
| Tie Rod Dust Boots - Part Number: 191712 Customer: Tyrel Williams Rating: 5 out of 5Overall Opinion: They suck These are made for tie rods for a front wheel drive car. The description said they would fit my 1 ton pickup, and they most definitely did not. Pretty much it was money down theper. Only buy if you are using them on a front wheel drive car. |
| Tie Rod Dust Boots - Part Number: 191712 Customer: Roger Pfister Rating: 5 out of 5Overall Opinion: Fast shipping, right part and very nice communication! What else...ahh thanks very much again! Roger from switzerland |
| Tie Rod Dust Boots - Part Number: 191712 Customer: robert peric Rating: 5 out of 5Overall Opinion: excellent fit great Great product. Easy to fit and looks good once fitted. |
| Tie Rod Dust Boots - Part Number: 191712 Customer: Tim McGuire Rating: 5 out of 5Overall Opinion: Great Product These boots fit like a glove and are much thicker then the original boots. As other boots and bushings wear out I will replace them with your product.Thanks |
| Tie Rod Dust Boots - Part Number: 191712 Customer: Troy Nelson Rating: 5 out of 5Overall Opinion: Nice price - fit well I couldn't find these anywhere locally, allowed me to replace the boots on good tire rod ends - very pleased. |
| Tie Rod Dust Boots - Part Number: 191712 Customer: Troy A. Harrison Rating: 5 out of 5Overall Opinion: Excellent very snug fit, exactly what is required- very pleased |
| Tie Rod Dust Boots - Part Number: 191712 Customer: ANDRE TRUJILLO Rating: 5 out of 5Overall Opinion: great! great item! |
| Tie Rod Dust Boots - Part Number: 191712 Customer: Steven Shawver Rating: 5 out of 5Overall Opinion: very good The boots were exactly what I needed, they fit perfectly no problems |
 | Tie Rod Dust Boots - Part Number: 191713 Customer: Donald Peterson Rating: 5 out of 5Overall Opinion: Good These are hard to find for a 1983 Mazda. They were delivered promptly. It was the same boot for both the ball joint and tie rod end. The ball joint boot stretched out to fit. Time will tell how well they hold up. |
 | Tie Rod Dust Boots - Part Number: 191714 Customer: william cooper Rating: 5 out of 5Overall Opinion: saved alot of money didnt have to replace the while part Good product good price good fit. |
| Tie Rod Dust Boots - Part Number: 191714 Customer: James Hunt Rating: 5 out of 5Overall Opinion: Great product! Installed these on an 88 Nissan 200sx which didn't have any dust boots on the tie rods. I cut a small notch out of one side of these in order to make them form fit over my tie rods and they fit and work perfect! |
 | Ball Joint Dust Boots - Part Number: 191715 Customer: Tim Garrison Rating: 5 out of 5Overall Opinion: Great Fit & look great. |
| Ball Joint Dust Boots - Part Number: 191715 Customer: John Anne Jr. Rating: 5 out of 5Overall Opinion: Excellent This product is well designed and of good quality. I would recommend this product to anyone who is looking to replace the dust boots on their vehicle. |
| Ball Joint Dust Boots - Part Number: 191715 Customer: Jimmy L Whalen Jr Rating: 5 out of 5Overall Opinion: Good but not great Uppers went on with no problem. However the lowers were a bit to small to seal around the top of the ball joint. When installed one side wanted to fold up leaving an open spot. I had to take them off and and work the lower lip out a couple of times. This required them coming off and on a few times. The last time I installed them I used a small flat blade screw driver to hold the lip out when I dropped the spindle back on. After this they seemed to stay on and made contact all the way around the bottom. I can say the company was very helpful and shipped them to me right away. I can also say I would buy from them again without question. As with most after market parts there is always a little fine tuning to get things to fit. This part was going on a 1937 Pontiac coupe with a 1968 Nova front clip I have changed from drum brakes to disc brakes. |
| Ball Joint Dust Boots - Part Number: 191715 Customer: Frank Mauceri Rating: 4 out of 5Overall Opinion: Good quality service part The Prothane Ball Joint Dust Boots fit well and appear to be very good quality. They are not designed as the originals, so should not be considered for a show quality restoration. If you need replacement boots for a daily driver, you will find these to be perfect. |
| Ball Joint Dust Boots - Part Number: 191715 Customer: Troy A. Harrison Rating: 5 out of 5Overall Opinion: Perfect Match! worked great - no issues - very pleased! |
| Ball Joint Dust Boots - Part Number: 191715 Customer: Sherell Shepherd Rating: 5 out of 5Overall Opinion: Great Speedy shipping , nice sales personel , great quality. Thanks! |
| Ball Joint Dust Boots - Part Number: 191715 Customer: mark chonoski Rating: 5 out of 5Overall Opinion: fits correctly Very pleased with the boots. Easy installation and they fit correctly as should. |
| Ball Joint Dust Boots - Part Number: 191715 Customer: brian rogers Rating: 5 out of 5Overall Opinion: parts were well made The ball joint dust boots fit my 69 camaro pretty well. The fit over the stud was perfect, although they seemed a little tight on the ball end. It looks like they will function as expected. I like them over the stock parts. |
 | Ball Joint Dust Boots - Part Number: 191717 Customer: Morris Blackburn Rating: 5 out of 5Overall Opinion: Good This product saves time and money. |
 | Shock Resevoir Mount Bushings - 1.5/2.5 Inch Diameter - Part Number: 191719 Customer: Don Groccia Rating: 5 out of 5Overall Opinion: Good quality, perfect fit.. A+++ Installed with no issues. Matched contours perfectly. |
 | Super Grease 3 Pack - Part Number: 191750 Customer: James Roberts Rating: 5 out of 5Overall Opinion: Easy to apply and good quality This worked great on my rear sway bar bushings. Keeps the squeaks away. Good stuff! |
| Super Grease 3 Pack - Part Number: 191750 Customer: Ray Tseng Rating: 5 out of 5Overall Opinion: Works well. Just what was needed to re-lubricate and remove squeak from my poly sway bar bushings. It is a very sticky lubricant (like half-dried elmers glue), so it is probably not appropriate for general lubrication purposes other than this specific application for motor vehicle poly bushings. |
 | Super Grease - 14 oz. Tube - Part Number: 191751 Customer: Steven Stanley Rating: 5 out of 5Overall Opinion: Excellent Lube Used Prothane on MOOG Upper and Lower Ball joints, also outer MOOG tie rods with grease zerts. Front End works great. |
 | Front Sway Bar Endlinks - Part Number: 19401 Customer: A Harry Rating: 5 out of 5Overall Opinion: Great quality Easy to install, superb quality and excellent fit. Bushings are really stiff and the rods look a good bit more hefty that stock. Great part. |
 | Front Sway Bar Endlinks - Part Number: 19402 Customer: Erik Rating: 5 out of 5Overall Opinion: Cheap price and Effective Installed these instead of OEM replacements for the simple fact that these are cheaper in price. They work as they should and have held up vastly better then OEM. |
| Front Sway Bar Endlinks - Part Number: 19402 Customer: brent luce Rating: 5 out of 5Overall Opinion: time the endlinks are great but it took more than 2 weeks to get the red ones in the lenght i needed |
| Front Sway Bar Endlinks - Part Number: 19402 Customer: Jeffry Mooney Rating: 5 out of 5Overall Opinion: Super Exactly correct. Fit nicely and can't wait to take the motor home for a "twisty" cruise. The old ones were shot and falling out so these would be an improvement but the much higher durometer rating should solve some other issues also. |
 | Front Sway Bar Endlinks - Part Number: 19403 Customer: Miker Zimmerman Rating: 5 out of 5Overall Opinion: Very Good Works well. |
| Front Sway Bar Endlinks - Part Number: 19403 Customer: Tim Heathcoat Rating: 5 out of 5Overall Opinion: These are high quality and fit perfect for my application. |
 | Front Sway Bar Endlinks - Part Number: 19408 Customer: Gary Replogle Rating: 5 out of 5Overall Opinion: I have installed my parts and I'm very pleased. The service was great, shipping was quick. Parts are made of quality material and I will use Energy Suspension again. |
| Front Sway Bar Endlinks - Part Number: 19408 Customer: Lyle Hughes Rating: 5 out of 5Overall Opinion: Great product Great replacement. Complete with all bits that were required. |
| Front Sway Bar Endlinks - Part Number: 19408 Customer: Lloyd Cormier Rating: 5 out of 5Overall Opinion: Excellent product Great fit and grade. Could not of asked for any better. |
| Front Sway Bar Endlinks - Part Number: 19408 Customer: Jerry Bahr Rating: 5 out of 5Overall Opinion: Went on easily work great Look great work even better, fast friendly service would recommend to anyone. |
 | Front Sway Bar Endlinks - Part Number: 19409 Customer: Troy A. Harrison Rating: 5 out of 5Overall Opinion: Perfect match, bolted right up! I actually blasted the gold parts, and repainted black - it worked great! |
 | Rear Sway Bar Endlinks - Part Number: 19413 Customer: Shane Curry Rating: 5 out of 5Overall Opinion: Awesome!!! The sway bar end-links were awesome. Much better and stronger than OEM. I have broken two sets bought from the dealer in the past. Quick order, fast delivery, easy installation, more than satisfied! |
 | Front Sway Bar Endlinks - Part Number: 19417 Customer: John Traugot Rating: 5 out of 5Overall Opinion: Great product !!!!! Parts arrived very quickly. Very easy to install and made world of difference |
 | Front Sway Bar Endlinks - Part Number: 19424 Customer: Timothy Ho Rating: 5 out of 5Overall Opinion: Good kit Easy installation. Excellent upgrade from stock for a noticeable improvement in handling. |
 | Endlink Grommets 3/4 X 1-1/4 Inch OD - Part Number: 19426 Customer: Greg Spannan Rating: 5 out of 5Overall Opinion: Good Parts are just what I expected and arrived on time. I purchased these for my Freightliner motorhome chassis. Did not fit, but I will hang onto them for future projects. I was an engineer for Firestone Airsprings at one time and worked with silent block bushings. Your product looks good. Regards, Greg |
 | Front Endlink Bushings - Part Number: 19431 Customer: Rodney Spracklin Rating: 5 out of 5Overall Opinion: excellent to deal with.. Highly recommended seller. |
 | Pivot Bushings - 1-1/8 OD - 1/2 ID - 1 Inch Long - Part Number: 19601 Customer: Jamie Smith Rating: 5 out of 5Overall Opinion: Excellent quality These components are of the best quality. I had a bad shimmy (death wobble, if you have a lifted jeep you know the problem) in my lifted Jeep Grand Cherokee. The Rough Country steering stabilizer rubber bushings are garbage. I pressed these new bushings in and it drives like new. Super fast shipping and you can not beat the price Thank you for a great product. |
| Pivot Bushings - 1-1/8 OD - 1/2 ID - 1 Inch Long - Part Number: 19601 Customer: JIMMY NELSON Rating: 5 out of 5Overall Opinion: the parts were great To be honest i used these bushing on a 1938 chevy. I understand the shackles were made by someone else. The bushings solved my problem, but were not a true application on this job. The bushing served the purpose for what i needed to do on the home made shackels. Thanks for bailing me out |
 | Pivot Bushings - 1-1/8 OD - 9/16 ID - 1 Inch Long - Part Number: 19602 Customer: robert warren Rating: 5 out of 5Overall Opinion: Good service and parts, will use again . bwarren, san marcos texas |
| Pivot Bushings - 1-1/8 OD - 9/16 ID - 1 Inch Long - Part Number: 19602 Customer: Justin Robitaille Rating: 5 out of 5Overall Opinion: awesome part is exactly what i needed and i could not ask for more from the product or the company, will do business again! |
 | Pivot Bushings - 1.25 OD - 1/2 ID - 1.25 Inch Long - Part Number: 19603 Customer: william Ketelaars Rating: 5 out of 5Overall Opinion: very good Love the product works well. However I thought there was only 2 urethane bushing and 1 steel sleeves per box. There are 4 urethane bushings and 2 steel sleeves per box which gave me double the quantity I needed. |
| Pivot Bushings - 1.25 OD - 1/2 ID - 1.25 Inch Long - Part Number: 19603 Customer: robert biscchoff Rating: 5 out of 5Overall Opinion: Great product Used these to make a transaxle mount. They worked great. The service I got was outstanding. Fast shipping |
| Pivot Bushings - 1.25 OD - 1/2 ID - 1.25 Inch Long - Part Number: 19603 Customer: dale anderson Rating: 5 out of 5Overall Opinion: Nice parts, fit super Nice parts, as described, fit super. |
| Pivot Bushings - 1.25 OD - 1/2 ID - 1.25 Inch Long - Part Number: 19603 Customer: Mitya Dikasov Rating: 5 out of 5Overall Opinion: NICE!!! Very reliable and easy to install product! The experience of the use of polyurethane - should last for longer than standard rubber. |
| Pivot Bushings - 1.25 OD - 1/2 ID - 1.25 Inch Long - Part Number: 19603 Customer: James Barone Rating: 5 out of 5Overall Opinion: Fantastic!! These bushings are excellent quality and fit perfectly. I would choose no other manufacturer then Prothane, through energysuspension.com for all of my fabrication needs. |
 | Pivot Bushings - 1.25 OD - 9/16 ID - 1.25 Inch Long - Part Number: 19604 Customer: Carl Napoli Rating: 5 out of 5Overall Opinion: Great product!!! Fortunately I kept the old sleeves as the new ones were the wrong inner dimension. |
 | Pivot Bushings - 1-1/2 OD - 1/2 ID - 2 Inch Long - Part Number: 19605 Customer: eric lee 1031 Rating: 5 out of 5Overall Opinion: Perfect and good quality fitment. I have build my own motor mount with these bushing. Quality is excellent, and shipping was fast. Will do business again. |
| Pivot Bushings - 1-1/2 OD - 1/2 ID - 2 Inch Long - Part Number: 19605 Customer: paul m seefeld Rating: 5 out of 5Overall Opinion: Very Satisfied The bushings I ordered fit perfectly. The project hasn't hit the trails yet but, I'm sure they will function perfectly as well. I will definitely use more of your products in the future. Thank You, Paul Rubicon Repair |
| Pivot Bushings - 1-1/2 OD - 1/2 ID - 2 Inch Long - Part Number: 19605 Customer: Tim Heathcoat Rating: 5 out of 5Overall Opinion: Works great for a motor mount and transmission mount. |
 | Pivot Bushings - 1-1/2 OD - 9/16 ID - 2 Inch Long - Part Number: 19606 Customer: Gordon m Dustan Rating: 5 out of 5Overall Opinion: Dont know yet I bought the bushings to modify for a custom application. I haven't had time to narrow the bushings, but I'm sure they'll work out well. The quality of the bushings is what I've come to take for granted with Prothane. |
| Pivot Bushings - 1-1/2 OD - 9/16 ID - 2 Inch Long - Part Number: 19606 Customer: Robert Figueria Rating: 5 out of 5Overall Opinion: Excellent quality! Perfect for making your own bushed rod ends using 2 in x 1/4" DOM tubing. |
| Pivot Bushings - 1-1/2 OD - 9/16 ID - 2 Inch Long - Part Number: 19606 Customer: kevin m monahan Rating: 5 out of 5Overall Opinion: good I have to say the first set I ordered from energy wasn't available with the sleeve size I needed so I machined them larger to fit. I wasn't surprised when I only got 2 years out of them. This set was to the exact spec I needed and have been working well. And for the price you cant replace factory rubber for less. However they've only been in 2 months. Well see what 2 years brings. Even then, still a quarter the price of factory bushings. |
| Pivot Bushings - 1-1/2 OD - 9/16 ID - 2 Inch Long - Part Number: 19606 Customer: Westley Hancock Rating: 4 out of 5Overall Opinion: Great product Great quality product for the price, it's my second time buying a set of these bushings and I definitely will purchase them again |
| Pivot Bushings - 1-1/2 OD - 9/16 ID - 2 Inch Long - Part Number: 19606 Customer: Eric S Rating: 5 out of 5Overall Opinion: Great Product! Product came exactly as expected and is great for high performance custom suspension work like ours. |
 | Pivot Bushings - 1.5 OD - 1/2 ID - 2.5 Inch Long - Part Number: 19607 Customer: Jon Titus Rating: 5 out of 5Overall Opinion: looks good. Turns out I ordered the wrongs ones, however the quality is as good as any other poly bushing. As I'm doing custom fab I will surely find a use for them |
 | Pivot Bushings - 1.5 OD - 9/16 ID - 2.5 Inch Long - Part Number: 19608 Customer: Craig Hessenius Rating: 5 out of 5Overall Opinion: High Quality Parts. These parts are ultra high quality and very consistent on the dimensions. You will be pleased if you buy these. This company is first rate A++ and fast reasonable shipping. I will buy again. |
| Pivot Bushings - 1.5 OD - 9/16 ID - 2.5 Inch Long - Part Number: 19608 Customer: TIMOTHY BLEDSOE Rating: 5 out of 5Overall Opinion: Grate product Rancho quit making the control arm bushings, these fit just like they were made for them. Great product |
| Pivot Bushings - 1.5 OD - 9/16 ID - 2.5 Inch Long - Part Number: 19608 Customer: Jesse Lee Rating: 5 out of 5Overall Opinion: Works great for links, and other misc mounts that require some isolation. |
| Pivot Bushings - 1.5 OD - 9/16 ID - 2.5 Inch Long - Part Number: 19608 Customer: Georgia Skamaga Rating: 5 out of 5Overall Opinion: great Exactly as wanted and expected! |
| Pivot Bushings - 1.5 OD - 9/16 ID - 2.5 Inch Long - Part Number: 19608 Customer: paul mckibben Rating: 4 out of 5Overall Opinion: Good product. I bought these for my 1991 Cadillac Eldorado. The factory replacement parts required a special tool for installation and I couldn't find a machine shop, or dealer, who was able to press the factory bushings into the control arm. I took a chance on the Energy Suspension bushings and was able to modify them to fit with a Dremel tool and a bench grinder (the Energy Suspension part was 1/4 inch to long). After reducing the length of the sleeve and bushing the part was a perfect fit. |
 | Front Shock Mount Bushings - Stem Type - Part Number: 19901 Customer: Matthew woodstrup Rating: 5 out of 5Overall Opinion: Good. Worked fine. Fit correctly. Would like to see the bottom bushings for the same shock. |
| Front Shock Mount Bushings - Stem Type - Part Number: 19901 Customer: David B Wadleigh Rating: 5 out of 5Overall Opinion: High quality parts, good for restorations. Consistent shape and color, good both functionally and as a restoration "OE looking" item. |
| Front Shock Mount Bushings - Stem Type - Part Number: 19901 Customer: Robert Moncrief Rating: 5 out of 5Overall Opinion: Great Parts work great. My International rides smother with no metal to metal rattles. Would recommend. Will buy for other projects. |
 | Shock and Steering Stabilizer Bushing - Small Nipple Type - Part Number: 19902 Customer: Robert E Meunier Rating: 5 out of 5Overall Opinion: These were for a Steering Stabilizer that was short these bushings. Exactly what I needed and shipped fast. They fit perfectly. Very pleased. |
 | Shock Mount Bushings - Straight - 5/8 Inch ID - Part Number: 19909 Customer: scott r capener Rating: 5 out of 5Overall Opinion: very good product I used this product to repair an edelbroch IAS twintube shocks. The front grommets were worn out and in need of being replaced. The shock itself was still in operating condition. These bushings are excellent replacement parts, fit and finish are just like original equipment. The price of the part justifies the cost to repair the shock. I will use this product to replace the rest of the shock bushings when they are worn out. |
 | Shock Mount Bushings - Hourglass Large Halves - 3/4 Inch ID - Part Number: 19918 Customer: rodney scott Rating: 5 out of 5Overall Opinion: I'm a return customer, you have great products. In the past I've purchased body mounts and bushing kit for my jeep and was very satisfied with the quality of the materials and workman ship which made installation quick and easy. I advise others of the quality products you make. Your satisfied customer R. Scott |
 | Shock Mount Bushings - KONI 1/2 Inch ID - Part Number: 19919 Customer: David Allen Rating: 5 out of 5Overall Opinion: Good Quality The product met the needs for my application. Customer care was excellent. |
 | Shock Mount Bushings - Bilstein 12MM ID - Part Number: 19920 Customer: Cameron Sanders Rating: 5 out of 5Overall Opinion: Great Used these bushings on a set of bilstein 7100 reservoir shocks to replace the uniballs (in order to use stock mounts). |
 | Front Sway Bar and Endlink Bushings - 19mm - Part Number: 221101 Customer: Joshua D. Mills Rating: 5 out of 5Overall Opinion: Very helpful I used these bushings with my stock sway bar obviously and with 249,000 miles the stock rubber bushings were far from decent. So these polyurethane bushings were a big help. I can definitely feel the corners better and for $18 shipped to my house, the value was unbeatable. Highly recommended if you don't have the cash for a new front sway bar kit. |
| Front Sway Bar and Endlink Bushings - 19mm - Part Number: 221101 Customer: AJ Bastioli Rating: 3 out of 5Overall Opinion: Nice build quality & appearance The bushings are very much on the squeeky/creeky side of the equilibrium. I used all of the lube included with the kit and only used the sway bar bushings(not endlinks or other 4 pieces) and I get noise from them upon take off and in cornering. Ive had them in for a month and it hasn't stopped. If my car wasn't as heavily modified as it is, it would bother me, but with Stage 1 motor mounts and low suspension, It doesn't bother me. |
| Front Sway Bar and Endlink Bushings - 19mm - Part Number: 221101 Customer: Dan A Fravel Rating: 5 out of 5Overall Opinion: The end links DID NOT work with my year? 1997 VW jetta vr6 |
 | Total Kit - Part Number: 222004 Customer: Dennis Bachman Rating: 5 out of 5Overall Opinion: Very good parts I installed the front bushings and they fit very well and the control arms do not shake as they did with the old bushings. |
| Total Kit - Part Number: 222004 Customer: Jack B. Willis Jr. Rating: 5 out of 5Overall Opinion: Awesome SUPER nice kit !!! Easy to install! |
 | Total Kit - Part Number: 222008 Customer: Louis Barey Rating: 5 out of 5Overall Opinion: Very good Very good quality ! |
| Total Kit - Part Number: 222008 Customer: Shawn Hartzell Rating: 1 out of 5Overall Opinion: sthartzell@msn.com I was not happy with the Transylvania mount. My little girl was going for her first win at Rattlesnake Raceway and the mount ripped out of the bolts. I think it could work if they put a plate inside of it to keep it from coming apart. The mount was only in for that race 30 laps top speed of 60 MPH stock motor right out of picknpull no power mods at all; it's against the rules to change anything on the cars. |
| Total Kit - Part Number: 222008 Customer: Alexander Hanak Rating: 5 out of 5Overall Opinion: Very Pleased I was very pleased with my purchase with the Prothane suspension / engine mount kit. The price and shipping were fantastic. Having had this kit on my ITB rabbit back in the early 90s I was aware of the engine vibration transfer to the passenger compartment but was willing to for go this on my cabrio daily driver to have less rock and roll of the drivetrain. I just mention this to have testimonial for other purchasers. I believe you mentioned this in your add about this vibration issue. Thanks again. Sincerely, Alex |
| Total Kit - Part Number: 222008 Customer: Norbert Munteanu Rating: 5 out of 5Overall Opinion: greate stuff Everything fits together like a glove and holds all the parts together real nice |
 | Total Kit - Part Number: 222009 Customer: Carlos Hernandez Rating: 5 out of 5Overall Opinion: Great quality Great quality at a good price, perfect as the original installation |
| Total Kit - Part Number: 222009 Customer: martin clayville Rating: 4 out of 5Overall Opinion: I am pretty satisfied with my purchase overall, just be sure to take a measurement of your sway bar before ordering. The kit came with a 19mm sway bar bushing set and my 85 jetta Gli has a 17mm sway bar. |
| Total Kit - Part Number: 222009 Customer: Ryan Osler Rating: 5 out of 5Overall Opinion: Very happy with the product! I installed the products and I am very happy with the results!! |
| Total Kit - Part Number: 222009 Customer: João Marcio Souza Rating: 5 out of 5Overall Opinion: Excellent Product of outstanding quality. Excellent |
| Total Kit - Part Number: 222009 Customer: Jason Bussewitz Rating: 5 out of 5Overall Opinion: excellent fit and great value I liked the overall fit and how these bushings stiffened up the car. For the most part they were easy to install, and fit like they were factory made for the car. They came with everything needed to install them including the special grease to prevent squeaking. The only thing I found to be a little out of proportion is the steering rack bushing. It does work fine, but has big gaps on the bottom corners, whereas the original bushing on the car wraps around completely. Overall, I would recommend anyone with a VW, that these will fit, to install them! The car sways less, rides more firm, and has a little better traction as well. Thanks for making a great product that is reasonably priced to boot! |
 | Front Control Arm Bushings - Part Number: 22201 Customer: VW Flopsy Rating: 1 out of 5Overall Opinion: Horrible Squeaking!! Horrible squeaking over every bump! Manufacturer provides lubrication; however, it only helps with installation. After that you are on your own to lubricate it on a regular basis (~1x/month). Manufacturer Tech support has yet to get back with me regarding. In your hand, these bushings are no doubt stiffer than rubber (able to make a mark with my finger nail; the bushing then regains its original shape). However when installed on the car, I don't notice too much of a difference. Installation is easier than a rubber bushing; took a lot of hammering to get into the control arm, but nothing too major. Shipping was fast. EnergySuspensionParts staff get high marks for quick respond rate and for helpfulness in directing me toward the manufacturer. However in regard to the product, feel free to purchase if you want a squeaky car. |
| Front Control Arm Bushings - Part Number: 22201 Customer: gerald andrews Rating: 5 out of 5Overall Opinion: excellent parts were shipped fast. great fit and performance |
 | Front Control Arm Bushings - Part Number: 22202 Customer: Jim McKinnon Rating: 5 out of 5Overall Opinion: AAA+++ Fantastic product. Very easy to install. Will buy again |
| Front Control Arm Bushings - Part Number: 22202 Customer: Eric Vandomselaar Rating: 5 out of 5Overall Opinion: Great! After driving to Matamoros Mexico for over 6 months my car had developed several severe suspension problems and I did not realize how bad they were. I drive 150 miles between my home and work 5 times a week. There are more than 20 speed bumps on my way to work.... yes 40 in total! The MK4 GLI models are known to have problems with the larger rear busing since VW had left spaces in the bushings so after some 90K to 100K miles these bushing wear badly and make noises etc. Bad alignment to boot. After installing these Prothane bushing the car changed: better handling, tight steering, and very solid all of a sudden. If you are a avid VW driver like I am do yourself a favor and install these on your MK4. You'll be happy you did!! |
| Front Control Arm Bushings - Part Number: 22202 Customer: alex griffith Rating: 5 out of 5Overall Opinion: Great product super fit and top quality. Fitted these to my Audi a3 8l as it shares the same suspension as the golf 4. Outstanding fit and super solid and rigid compared with oem rubbers. Great product very happy with them. Cheers |
| Front Control Arm Bushings - Part Number: 22202 Customer: Driver007 Rating: 4 out of 5Overall Opinion: Performs great 01 Jetta: They said suspension makes noise and it does. Not the same sound as the bushings going out. Overall I like the bushings because the steering wheel is tighter(steering wheel travel) and it is a bit tougher to turn, not much though. |
| Front Control Arm Bushings - Part Number: 22202 Customer: Platon Tim Rating: 5 out of 5Overall Opinion: Like this At this moment only some miles driving with this bushings, but I love them, car a little bit harshly, but feeling of wheels is much better, car drives where I want, so in other words perfect feeling and enjoying from driving. |
| Front Control Arm Bushings - Part Number: 22202 Customer: brandi fugate Rating: 5 out of 5Overall Opinion: Great porducts Helped to tighten up the front of my car. Helped with wheel hop. |
| Front Control Arm Bushings - Part Number: 22202 Customer: Aleksey Lissevtsev Rating: 5 out of 5Overall Opinion: AlekseyLiss@mail.ru They're very nice bushings. Steering wheel gets a great response! |
| Front Control Arm Bushings - Part Number: 22202 Customer: Thomas Stewart Rating: 3 out of 5Overall Opinion: not to shabby! the parts are incredibly high quality but i did find that they were not an exact fit.. my 1985 VW cabriolet is the same as an 85 rabbit and an 85 golf as far as most things are concerned but the length of the metal CORE of the control arm bushings were to short so i had to cut apart a different bushing and used that core.. otherwise fantastic products i love them and will buy them in the future! any plans for front strut bushings??? any help on anything else that will fit my car i bet it all needs replacing you guys suggest ill buy them! |
 | Motor Mount Insert - Front - Part Number: 22501 Customer: Daniel Kersey Rating: 5 out of 5Overall Opinion: Great Stuff!!! Super tight fit without any mods. The mount is very hard, but has just the right amount of give to install with only a vice. It allows very little vibration and movement. I am very happy with Energy Suspensions take on this VW nose mount. |
| Motor Mount Insert - Front - Part Number: 22501 Customer: Chaz Donald Rating: 3 out of 5Overall Opinion: Part was as described The part came quickly and was in good condition, however I would not recommend it for the diesel rabbit, for mine shook old mans angry fist. |
 | Rear Motor Mount Inserts - Part Number: 22502 Customer: Daniel Kersey Rating: 5 out of 5Overall Opinion: Super motor mount I was expecting this mount to be super hard and wound cause a bad vibration but I was WAY wrong. This is a super mount plenty hard but with superior vibration damping. There is no way I could be any happier with is mount. Dan K MK 1 VW Rabbit Convertible. |
| Rear Motor Mount Inserts - Part Number: 22502 Customer: Eric Davis Rating: 5 out of 5Overall Opinion: Fits perfect Fits perfect and comes with all the hardware.... 5 stars |
 | Motor Mount Inserts - Left - Part Number: 22505 Customer: Daniel Kersey Rating: 3 out of 5Overall Opinion: So So The design is good but the fit and finish is bad. I had to spend an hour with my drimel tool grinding away about 10% of the mount to get it to fit inside the rubber mount its design to fit inside of. Plus the polyurethane was pitted up badly. I bought 3 mounts at the same time, all were perfect but this one is use able junk. Dan K Louisville Ky MK 1 VW Rabbit |
| Motor Mount Inserts - Left - Part Number: 22505 Customer: rick donley Rating: 5 out of 5Overall Opinion: Good Great part although I had to modify a little to fit, but only because a different mount had been installed. I would recommend this to anyone who needs to replace a right mount on a Rabbit. The original mounts are very hard to install. |
 | Lower Engine Torque Arm Mount Inserts - Part Number: 22506 Customer: Nicholas Weiss Rating: 5 out of 5Overall Opinion: Very sporty ride, higher torque felt This was a very easy install. The red inserts are for a sportier ride. |
| Lower Engine Torque Arm Mount Inserts - Part Number: 22506 Customer: stephen woods Rating: 4 out of 5Overall Opinion: Pretty good Very easy to install, they work awesome at keeping the torsion movement down on the engine. Only complaint is they cause a vibration throughout the car, but not to severe. |
| Lower Engine Torque Arm Mount Inserts - Part Number: 22506 Customer: Don Potvin Rating: 2 out of 5Overall Opinion: How to turn you car into a vibrator The Prothane bushings are a much harder material than the original rubber bushings. The disadvantage to this is the additional vibration that is transmitted through the bushings and into the firewall of the car. The additional vibration is severe enough that it is actually audible. On a diesel, you want as much vibration dampening as you can get, and these bushings will take some of that dampening away. I will eventually change these back out to the OEM rubber bushings. |
 | Motor Mount Insert - Lower - Part Number: 22507 Customer: Kelvin Mui Rating: 5 out of 5Overall Opinion: Quick and easy to install. Great product. Makes a big difference in reducing wheel hop. Gear shifts are much more accurate. Grease/lube was not part of package for installation though. |
 | Rack and Pinion Bushing Kit - Part Number: 22701 Customer: Ricardo Velez Rating: 5 out of 5Overall Opinion: Perfect fit; overall high quality, no fitment issues. Great service, exact part for car/ model; zero problems. |
 | Rear Shock Tower Bushings - Part Number: 22902 Customer: michael szlashta Rating: 5 out of 5Overall Opinion: great Really tightened up the suspension on our jetta III. I have used these on other vw's I have had and really firm up the ride. |
 | discontinued by Prothane - Part Number: 2445109 Customer: Daryl Siefert Rating: 5 out of 5Overall Opinion: Very good quality pieces. These bushings are very good quality pieces. Fit well, easy to install. Tightened up the suspension quite a bit and really helped the handling. |
 | Front Control Arm Bushings - Lower Inner - Part Number: 2645045 Customer: Roger Perkins Rating: 5 out of 5Overall Opinion: not fitted yet. I;m sure they will work okay. I have Prothane suspension on other parts of my MGB. and i like the results. |
| Front Control Arm Bushings - Lower Inner - Part Number: 2645045 Customer: Joseph L Rating: 4 out of 5Overall Opinion: Pricey, But Excellent!! Hands down the best bushings Ive ever used. Absolutely love them, they are great. Unlike the new rubber replacements which disintegrate after a few short years, these seem like they will hold up for a very long time. My only complaint is that they are expensive. Money well spent, but for what they are, I feel like they could be made more affordable. |
| Front Control Arm Bushings - Lower Inner - Part Number: 2645045 Customer: Richard G. Liddick Rating: 5 out of 5Overall Opinion: Very nice improvement to my MGB So far I am very happy with the ride improvement on my 1977 MGB. In the future I need to replace all of my rubber bushings and I plan on using Prothane replacements. |
 | Rear Leaf Spring Bushings - Front Eye Position - Part Number: 2647082 Customer: Bruce K Stevenson Rating: 1 out of 5Overall Opinion: Wrong stuff I ordered these bushings on the assumption they would fit the rear springs on my 1`972 MGB. THEY DO NOT. The brass sleeves do not fit over the through bolts and the other bushings are too small for the front of the springs. I took the parts to a British car restoration outfit and they had no idea where these parts would fit. I was refused a refund. |
 | Rear Spring Rear Eye and Shackle Bushing Kit - Part Number: 2647083 Customer: George Chase Rating: 4 out of 5Overall Opinion: good product - satisfied I installed the rear spring bushings along with new poly spring pads and have noticed a tighter suspension and good road ride - beats the old rubber bushings. |
 | Rear Spring Pad Kit - Part Number: 2647084 Customer: George Chase Rating: 5 out of 5Overall Opinion: Noticed a great improvement in the feel of the rear suspension. I installed these along with new poly spring bushings. Greatly improved road handling and taughtness. |
 | Front Upper Inner Control Arm Bushings - Part Number: 2745095 Customer: scott price Rating: 5 out of 5Overall Opinion: Great product First rate product, fits perfect. Nicer that the hard poly bushings and was shipped out fast. |
 | Front Lower Inner Control Arm Bushings - Part Number: 2745096 Customer: scott price Rating: 5 out of 5Overall Opinion: Top notch bushings These bushings give a better feel than the hard poly bushings but don't give like the stock rubber bushings. They fit perfectly and were shipped out very fast. |
| Front Lower Inner Control Arm Bushings - Part Number: 2745096 Customer: Daryl Siefert Rating: 5 out of 5Overall Opinion: very good pieces These bushings are very high quality pieces. Fit well. Definitely tightened up the suspension and improved the handling. |
 | Rear Control Arm Bushings - Part Number: 2746067 Customer: Kenneth Hoff Rating: 5 out of 5Overall Opinion: they are what they are Last set had excessive wear between sleeve and bushing. Hope these wear better. |
 | Triumph Spark Plug Tube - Part Number: 2749043 Customer: Kenneth Jardine Rating: 2 out of 5Overall Opinion: Three of the spark plug tubes fit great but one of them the seals looked used and worn down I used sealer but I am still having trouble with it leaking oil Ken Jardine |
 | Front or Rear Motor Mount Inserts - V6 Only - Part Number: 28501 Customer: aaron manuel Rating: 4 out of 5Overall Opinion: They do the job very well but install is not fun. I feel a very good increase in throttle response so I am very pleased with them. The negative is that they are not at all easy to fit in the mounts. I found myself having to stand and bounce on these to get them in only to have them pop right back out once the weight was removed. It seems the molding could use a little bit of fine tuning. other than the fitment though, once they're in they do a great job. |
 | Rear Subframe Mount Inserts Kit - Part Number: 3101 Customer: Steve Elliott Rating: 5 out of 5Overall Opinion: Nice pieces Installed these on my 1976 BMW 2002 autocross car as part of an overall suspension stiffening and am pleased. |
 | Front Control Arm and Strut Arm Bushings - Part Number: 3201 Customer: DAVID Rating: 5 out of 5Overall Opinion: 5 Parts installed very easy. The kit had plenty of grease. The car is very happy, handles great. Thanks David |
 | Front Sway Bar Endlink Bushings - Part Number: 3401_Front Customer: Lucas Suer Rating: 5 out of 5Overall Opinion: good product I used these with an aftermarket (oversized) sway-bar on a 1973 BMW 2002. They fit right and make the entire assembly nice and tight. |
 | Rear Leaf Spring and Shackle Bushings - 2 Inch Main Eye - Part Number: 41001 Customer: sven frackelton Rating: 5 out of 5Overall Opinion: a tight rear feels good........ i changed over to a 65 axle on my 64 dodge 440 to get rid of the tapper axles. wanted to go high performance on this rear end. to put rubber bushings in on the leaf springs after upgrading everything else on the rear. i cant say the prothane bushing changed the handling , but i will say i know they are not the week spot on a kick rear end. be sure to take the outside metal of the old rubber bushing out before installing , as these are already a tight fit. |
| Rear Leaf Spring and Shackle Bushings - 2 Inch Main Eye - Part Number: 41001 Customer: dennis jansen Rating: 5 out of 5Overall Opinion: very good. Very fast shipping and easy to install. |
 | Rear Leaf Spring Bushings - Part Number: 41003 Customer: bruce schrader Rating: 5 out of 5Overall Opinion: Very nice quality parts, everything I needed !! Fast delivery, everything fit very well, easy installation, great doing business with you, the car rides great !!!!!! |
 | Front Leaf Spring Eye Bushings Kit - Part Number: 41005 Customer: Michael Bentley Rating: 2 out of 5Overall Opinion: they looked good I sent a email to confirm what I was getting.they told me it was for my truck.maybe would have fit if I had a Toyota and not a dodge Cummins |
 | Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 41006 Customer: Charles Coggins Rating: 5 out of 5Overall Opinion: great part Installation easy. |
 | Rear Leaf Spring Eye and Shackle Bushings - 2.5 Inch Main Eye - Part Number: 41008 Customer: Tre Ginn Rating: 1 out of 5Overall Opinion: wouldve been great if they woulda fit These DO NOT fit a 2500 like the description says.... |
 | Body Mount Bushings - B Body - Part Number: 4101 Customer: Greg Hausler Rating: 5 out of 5Overall Opinion: excellent The fit was great, no installation problems. |
| Body Mount Bushings - B Body - Part Number: 4101 Customer: Danny Snyder Rating: 5 out of 5Overall Opinion: Good I have a 1973 Dodge Charger and the front 2 went in fine; however, the back 2 had to be tapered on the inside edge to get them to fit. They pressed in just fine after that! |
| Body Mount Bushings - B Body - Part Number: 4101 Customer: rick Dereniowski Rating: 5 out of 5Overall Opinion: looks very good i have not installed yet,but they look like this upgrade to these prothane bushings will be a superior replacement from oem originals. |
| Body Mount Bushings - B Body - Part Number: 4101 Customer: Manfred Hill Rating: 4 out of 5Overall Opinion: Good quality parts! I found the washers to be a bit "thin" or just too soft, when the center bolt bottomed out the washers went concave, I added the old washers and it looked much better. These bushings are extremely hard to find...but prothane pulled it off the shelf..Thanks |
 | Rear Leaf Spring and Shackle Bushings - 2 Inch Main Eye and 5/8 Inch Main Eye Bolt - Part Number: 41016 Customer: robert offenberger Rating: 5 out of 5Overall Opinion: I could not have ask for these parts to have worked better. They were great. |
 | Body Mount Bushings and Radiator Support Bushings - Part Number: 4102 Customer: Akos Horvath Rating: 5 out of 5Overall Opinion: perfect! Bolted in nice, easy install, and looks good too. Thanks |
 | Body Mount Bushings - Part Number: 4104 Customer: Joar Engen Rating: 5 out of 5Overall Opinion: very good I have a 1987 Pajero LWB i used 2 of this set it works great. |
 | Front Sway Bar Bushings - 7/8 Inch - Part Number: 41104 Customer: Mark Novak Rating: 5 out of 5Overall Opinion: As Advertised! Part came in exactly as expected. It fit well and the assembly is installed and working fine. I would recommend this product to anyone looking for an OEM fit and finish. |
| Front Sway Bar Bushings - 7/8 Inch - Part Number: 41104 Customer: Bob Trottier Rating: 4 out of 5Overall Opinion: Good The bushings fit well; although, they are not exactly like the originals. |
 | Front Sway Bar Bushings - 15/16 Inch - Part Number: 41105 Customer: Jacqueline DSantos Rating: 5 out of 5Overall Opinion: Fair Did not come with installation instructions. |
| Front Sway Bar Bushings - 15/16 Inch - Part Number: 41105 Customer: Scott Cole Rating: 5 out of 5Overall Opinion: highly recommended! Great product. I have used several energy products on my SuperBee. I highly recommend them. |
| Front Sway Bar Bushings - 15/16 Inch - Part Number: 41105 Customer: Jeremy Johnson Rating: 5 out of 5Overall Opinion: very pleased! I bought and returned about 8 different sway bar bushings before I saw these listed on eBay. I have a 1970 Dodge Coronet 440 and the listing was for a Roadrunner, none the less they looked right and I was no stranger to returning parts so I bought them on high hopes and sure enough they worked perfectly! Thank you for ending my search. For those at least, my search for many other parts continues. |
| Front Sway Bar Bushings - 15/16 Inch - Part Number: 41105 Customer: Tom Tsirbas Rating: 5 out of 5Overall Opinion: Great part... fits just like factory |
 | Front Sway Bar and Endlink Bushings - 13/16 Inch - Part Number: 41106 Customer: William Card Rating: 5 out of 5Overall Opinion: nice Nice kit. Fit was perfect. Handling much better. |
 | Front Sway Bar Bushings - 7/8 Inch - Part Number: 41108 Customer: Stephen Davis Rating: 5 out of 5Overall Opinion: Proper fit, finish, and easy to install. |
 | Rear Sway Bar Bushings - 16mm - Part Number: 41111 Customer: William T Tarleton Rating: 5 out of 5Overall Opinion: part fit nicely made a big difference removed most of the understeer even with the stock swaybar. |
 | Front Sway Bar Bushings - 20mm - Part Number: 41118 Customer: Daniel Harrison Rating: 5 out of 5Overall Opinion: If you own a neon then you know the 70 mph shake that they are plagued with. These bushings stopped it completely. I even drove up to 110 mph just to see if it just pushed the shake higher up! |
 | Front Sway Bar Bushings - 24mm - Part Number: 41120 Customer: William Schutzler Rating: 5 out of 5Overall Opinion: The parts worked great. |
 | Rear Sway Bar Bushings - 12mm - Part Number: 41130 Customer: wayne aylsworth Rating: 3 out of 5Overall Opinion: Not too bad. A little hard to install. |
 | Front Sway Bar Bushings - 28mm - Part Number: 41132 Customer: Larry Panton Rating: 5 out of 5Overall Opinion: excellent product Parts fit perfectly, everything including grease in the kit. Made a huge difference in handling. Now I just have to get control arm bushings installed with new shocks to really feel the increased handling. |
 | Front Sway Bar Bushings - 33mm - Part Number: 41134 Customer: ricardo M Frakes Rating: 5 out of 5Overall Opinion: great These went on great. I was concerned with the small amount of lube sent with them. Once I installed them they only required a very small amount of lube. The vehicle rides nice and tight now and no squeaks. Great service and fast as well. |
| Front Sway Bar Bushings - 33mm - Part Number: 41134 Customer: cesar santos Rating: 5 out of 5Overall Opinion: It was very easy to install |
| Front Sway Bar Bushings - 33mm - Part Number: 41134 Customer: Thomas Robicheaux Rating: 5 out of 5Overall Opinion: Amazed! I could not believe how much stiffer they were compared to factory rubber bushings. I replaced the front and back bushings with this brand and now there is almost no lean when going around corners in my friends 2000 Dodge Dakota 4wd. |
| Front Sway Bar Bushings - 33mm - Part Number: 41134 Customer: Ercle Herbert Rating: 5 out of 5Overall Opinion: Very good I have bought OEM bushings for years - after cleaning and greasing the sway bar and bushings, they dry out quickly and begin to make noise. These urethane bushings come with a very persistent, super high viscosity "prothane" grease that seems to be working with the urethane bushings to keep them quiet. We'll see after a few months how they hold up. |
| Front Sway Bar Bushings - 33mm - Part Number: 41134 Customer: Mark Fisher Rating: 5 out of 5Overall Opinion: Excellent product Definitely better than the stock rubber ones, which I have had replaced 2 times already. They stiffened up my front end considerably. I would recommend these to anyone. |
| Front Sway Bar Bushings - 33mm - Part Number: 41134 Customer: George W. Lynch Rating: 5 out of 5Overall Opinion: Very Good Product I installed my Prothane bushing on my 2001 Dakota 4X4 after having to listen to that horrid sound of squeaking from the front end. I found the installation was fairly easy and the bushing fit perfectly and without any problems. Since the replacement with the Prothane Bushing the front end no longer squeaks and the front stabilizer has helped cornering control. Feels much tighter. I plan to replace the upper and lower Control Arm Bushing this summer with the Prothane. The Prothane Bushing are great and I would highly recommend them to any one. |
| Front Sway Bar Bushings - 33mm - Part Number: 41134 Customer: Gregory Miller Rating: 5 out of 5Overall Opinion: Great Product!! Made a big difference in handling! The parts were easy to install and made a big difference in the handling of our Dodge Durango |
| Front Sway Bar Bushings - 33mm - Part Number: 41134 Customer: Joseph Skroko Rating: 5 out of 5Overall Opinion: Great I have used energy suspension for all of my projects and my daily drivers for years and will continue to do so. Great products. |
| Front Sway Bar Bushings - 33mm - Part Number: 41134 Customer: Bryan P Williamson Rating: 5 out of 5Overall Opinion: Good product Installed on my 2000 Dakota 4x4. These are the only bushings I could find as a set. I never did find lower bushings at any local parts store. Thanks for stocking this set from Prothane. By the way, this complete kit with shipping, was less expensive than just the frame to swaybar ones that are sold at:(insert local parts store)! |
| Front Sway Bar Bushings - 33mm - Part Number: 41134 Customer: Melanie Marhefke Rating: 5 out of 5Overall Opinion: Thankfully they fit My boyfriend installed these for me, but it took us countless times to find the proper ones that actually fit. He didn't seem to have much trouble installing them either. We were both quite happy. |
| Front Sway Bar Bushings - 33mm - Part Number: 41134 Customer: Joel Vanderpool Rating: 5 out of 5Overall Opinion: Good Quality replacement part I have a mechanical background so installation was a breeze, about 20 minutes. There are sources available on the internet to give detailed instructions. An impact wrench is a big help but not necessary. I did not realize how bad I needed these until I removed the old ones. I diagnosed the issue by the play in the sway bar but after removing the part I noticed the old bushings were worn right through with metal on metal contact. I also noticed the ride greatly improved after replacement. I used to over steer at intersections and just figured it was a truck thing. This in combination with new shocks a few months back made for a quality ride. Be sure to measure the diameter of your sway bar as Dodge put out many variations. |
 | Front Sway Bar Bushings - 35mm - Part Number: 41135 Customer: John Haefner Rating: 5 out of 5Overall Opinion: Excellent Excellent quality. Easy to install after removing old. Would purchase from you again. |
| Front Sway Bar Bushings - 35mm - Part Number: 41135 Customer: Animator Rating: 5 out of 5Overall Opinion: Bushings that revitalize performance It's easy to forget just how important bushings are to a car's overall feel and performance, particularly for highly tuned vehicles who's performance rides on the edge of the envelope where the communication between driver and machine is vital. It's here when performance bushings come into play as they not only provide improved performance and protection from damaging metal to metal contact but also transmit the specified amount of telemetry force to the driver. Something as simple as new bushings makes all the difference in driving with confidence in your vehicles handling ability. Energy suspension and its subsidiaries are the best. |
 | Front Sway Bar and Endlink Bushings - 34mm - Part Number: 41138 Customer: Alejandro Soto B Rating: 5 out of 5Overall Opinion: Excellent, is very fast installation and service |
| Front Sway Bar and Endlink Bushings - 34mm - Part Number: 41138 Customer: FRED GOULD Rating: 5 out of 5Overall Opinion: Great product and price Install was simple and easy, parts fit well . Thanks |
| Front Sway Bar and Endlink Bushings - 34mm - Part Number: 41138 Customer: Jeffrey Temple Rating: 5 out of 5Overall Opinion: Great Product My truck has just passed 100000 miles and these were just what it needed. Realistically at that mileage all rubber should be replaced anyways. These bushings improved the roll that I was getting and improved the overall ride of the truck. Thanks! I will be ordering again very soon! |
 | Front Strut Arm Bushings - Part Number: 41202 Customer: Nate Carls Rating: 5 out of 5Overall Opinion: Excellent Fits the application well. The only item worth mentioning was noticed after install. The roll pin, that is installed within an inch of the end of the engine bay side of the strut arm to keep the nut on, cannot be reinstalled due to overall thickness of new product. The pin hole is buried beneath the keeper nut since the nut doesn't snug down as far as it used to. The simple solution is to drill a new hole into the strut arm just outside of the nut to ensure it stays on. |
| Front Strut Arm Bushings - Part Number: 41202 Customer: William Card Rating: 5 out of 5Overall Opinion: nice Nice upgrade. Great fit. |
 | Rear Bump Stops - Part Number: 41301 Customer: Jean Jolicoeur Rating: 5 out of 5Overall Opinion: GREAT replacement product this is a great replacement product , it was easy to install , the shipment was FAST and the price is great tks |
 | Shifter Stabilizer Bushings - Part Number: 41605 Customer: Benjamin Rainey Rating: 5 out of 5Overall Opinion: Fast and easy replacement My factory bushings disintegrated around 101K miles. Since replacing the entire cable is $200+ for parts alone, these are an easy 30 minute replacement for those of us on a tight budget. |
| Shifter Stabilizer Bushings - Part Number: 41605 Customer: dennis tast sr Rating: 5 out of 5Overall Opinion: Very good Very easy to install. Fixed warn out stock bushings and stiffened shifter. |
| Shifter Stabilizer Bushings - Part Number: 41605 Customer: Duane Motley Rating: 5 out of 5Overall Opinion: Excellent!!! My Neon would not go into reverse. The dealer wanted $500 to fix it. At first I thought "How could these little things work? " They were great! Easy to install and made the shifter feel like it just came from the factory! |
 | Front Coil Spring Lift Isolators - 2 Inch - Part Number: 41706 Customer: Jesse Simms Rating: 5 out of 5Overall Opinion: Great for leveling your truck I purchased these to raise the front of my dodge ram. I replaced the struts as well. Leveled out really well. Great part. |
 | Motor Mount Inserts - 3 Mount Combo - Race - Part Number: 41901 Customer: Tom Taylor Rating: 5 out of 5Overall Opinion: Very pleased Installation of the inserts is relatively easy, once you figure it out. I bought my motor mounts for a 1998 Dodge Neon because the mounts were shot, and throwing these in made all the difference. It would be nice if they came with a diagram, but you can figure it out on your own. Performance wise, a stiffer transverse axle engine has much better response. Great product! |
 | Motor and Transmission Mount Combo - Part Number: 41903 Customer: Manfred Hill Rating: 5 out of 5Overall Opinion: Good quality parts! Part installed easily, fitment is good. I will buy Prothane again. |
 | Motor Mount Inserts - Upper and Lower - Race - Part Number: 41905 Customer: donald powell Rating: 5 out of 5Overall Opinion: ok. Received the parts in good time. Material appears to be of good quality. Parts did not fit easily into existing motor mounts. Removing the web from motor mounts is not an easy task. It is possible that the motor mounts are of poor quality. I had to remove part of the mount in order for the inserts to fit well.. ounce in the car, these parts seem to work very well. I ordered parts for a 2003 Neon 2.0. These look like the same parts used on certain Hondas. |
| Motor Mount Inserts - Upper and Lower - Race - Part Number: 41905 Customer: Michel van den Heuvel Rating: 5 out of 5Overall Opinion: Great product Very easy to install (takes about 30 minutes to install). It adds a little vibration when running at idle, but you'll get used to that. It's probably the best upgrade under $25 you can get. Wheel hop is eliminated, engine sits firmly in the mounts and almost doesn't move. Shifting performance is greatly improved, the power is more directly transferred to the wheel. |
 | Motor Mount Inserts - Upper and Lower - Street - Part Number: 41906 Customer: brian keel Rating: 5 out of 5Overall Opinion: Awesome! These units are slick. They go right in. Took about 20mins. They completely eliminated the sag in the engine. The axel sits where it should. No more loud clicking. Better yet my ex-wife isn't bugging me anymore about the car! |
| Motor Mount Inserts - Upper and Lower - Street - Part Number: 41906 Customer: brian scott Rating: 5 out of 5Overall Opinion: Very happy with them Easy to put on and they work great. |
| Motor Mount Inserts - Upper and Lower - Street - Part Number: 41906 Customer: Art Arvizu Rating: 5 out of 5Overall Opinion: Cool Very easy to install after a little trimming to fit the existing OEM part. Didn't really correct my problem though, I may have a broken Tranny mount. Overall, I like the product. |
| Motor Mount Inserts - Upper and Lower - Street - Part Number: 41906 Customer: dan Rating: 5 out of 5Overall Opinion: Easy install, works great! I highly recommend these to anyone regardless of vehicle use, they work great. |
| Motor Mount Inserts - Upper and Lower - Street - Part Number: 41906 Customer: Ron - Columbia City, Indiana Rating: 5 out of 5Overall Opinion: Incredible Improvement I received these inserts as a bonus with the "Hyperflex Master Kit" and didn't think much about it. I finally got them installed last week after having the parts for over a year. My car is a 00 Neon and has always had wheel hop issues and a "shimmy" feeling while accelerating through the gears, almost as if the engine was mis-firing. Since installation, these problems have gone completely away. There is zero wheel hop and the shifts and acceleration are smooth as silk. I bought this car brand new and if I had known then what I know now, I would've installed these inserts the day I brought the car home from the dealership. I don't know if they would have as drastic of an impact on an automatic transmission car, but if you have a manual trans, do yourself a favor and install these. You will not believe the improvement...especially for the money. |
 | Total Kit - Part Number: 42003 Customer: kurt Bealer Jr Rating: 5 out of 5Overall Opinion: satisfied Overall very happy with everything except the upper control arm bushings. They did not fit my application. |
 | Total Kit - Part Number: 42006 Customer: Joerg Andrzejweski Rating: 5 out of 5Overall Opinion: Everything fits perfect Installation is easy and the car feels like it looks. My PT Cruiser GT is fun to drive now. Best mod for the chassis. |
 | Total Kit - Neon SRT-4 - Part Number: 42007 Customer: Thomas Lafferty Jr Rating: 5 out of 5Overall Opinion: Great Products I finally had the time to install most of the set of bushings, and I must say that they make an incredible difference in the handling of my car. I really love the feeling it has now |
 | Front Lower Control Arm Bushings - Part Number: 4201 Customer: michael watson Rating: 5 out of 5Overall Opinion: Great product. Fit just like they should and install was easy. |
| Front Lower Control Arm Bushings - Part Number: 4201 Customer: Johnathan Bundy Rating: 5 out of 5Overall Opinion: Great looking product. I have installed the new bushings along with new ball joints,bearings and tie rod ends in my truck. The difference in the ride quality is night and day. The truck has never drove so good. Very happy with the bushings. |
 | Front Lower Control Arm Bushings - Part Number: 4205 Customer: hemi george Rating: 5 out of 5Overall Opinion: best of the best If you have a car, especially if it has no front sway bar, you must use these bushings. Otherwise, your front bushings ball joints will not last 2 - 3 thousand miles. I have been using these bushings last 20 years on all my cars, and recommend to all my customers . |
 | Front Control Arm Bushings (without outer metal shells) - Part Number: 4206 Customer: Nate Carls Rating: 5 out of 5Overall Opinion: Excellent Everything fits nice and tight and wasn't too difficult to install. |
 | Front Control Arm Bushings - Part Number: 4207 Customer: William Card Rating: 5 out of 5Overall Opinion: nice Installation went fine. Nice upgrade. |
| Front Control Arm Bushings - Part Number: 4207 Customer: Greg Hausler Rating: 5 out of 5Overall Opinion: Excellent Easy installation and fit was great |
 | Front Control Arm Bushings - Part Number: 4209 Customer: Robin Boomsma Rating: 5 out of 5Overall Opinion: The set of control arm bushings is the third set we have installed on two Neons - one used for autoslalom, the other used for short track oval competition. The oval track car was lost in a crash late last season, right front impact severely bent the lower control arm and split the vertical donut bushing, the other one survived and can be re-used. We did however install both new bushings along with a replacement control arm. These parts have proven to be easy to install and have performed to our expectations. Robin Boomsma |
| Front Control Arm Bushings - Part Number: 4209 Customer: Daniel Harrison Rating: 5 out of 5Overall Opinion: Very easy to install. Used a pitman arm puller to push the bushing out and this one slid right in. The car is way more responsive and no harshness. |
 | Front Control Arm Bushings - Part Number: 4214 Customer: Edward M. Banasik Rating: 4 out of 5Overall Opinion: Good - but time will tell I first had a Chrysler dealer change out the original bushings at 4 years and 16,000 miles. When I was told (during an oil change) that the bushings were bad again at 8 years and 26,000 miles I then had these prothane bushings professionally installed at a different repair facility so I could eliminate the issue of deteriorating rubber. I was told one side went in easily but the other sides vertical bushing was very difficult (to get the old bushing out). Now, for 99% of my driving, these urethane bushings work great but I get a banging noise when the wheel slowly drops about an inch from my concrete driveway apron to the asphalt street. There's no noise in potholes, just during slow drops of about an inch. For a professional to have trouble with the installation suggests this is not a job for amateurs. |
| Front Control Arm Bushings - Part Number: 4214 Customer: JC Hayes Rating: 5 out of 5Overall Opinion: Quality parts, difficult installation When it came time to replace the lower control arm vertical bushings - again - on my 05 PT Cruiser GT I elected to try poly. Good decision. I bought Energy Suspensions 3-piece bushings and Prothane's 2-piece set but I installed the Prothane set. Prothane's 2-piece bushings feel more substantial and are definitely the easier installation. (Tip: don't follow the instructions by pressing out the vertical bushing. Leave the shell in place, just drill out the rubber and clean it up with knives, razor blades, sand paper, etc. It's not that big a job.) Getting the rear bushing into place and the bolt through it as you install the control arm on a Cruiser is not a pleasant experience but it can be done. A strut compressor might ease installation. The problem is that the arm goes back in at an angle but the bolt won't line-up through the rear bushing with the arm at an angle: the poly bushings don't have the give in them the rubber bushings do. The people who say these bushings don't alter the way your car rides don't know what they are talking about. The first time you drive your car you will notice that the steering is precise, and I mean PRECISE - the car will go EXACTLY the direction you point the front wheels, assuming you don't have any other worn-out parts in the front end. No more monkey motion. Point the front wheels "that way" and the car goes "that way" not "that general direction." The ride is like listening to your favorite music on a better system, its the same music but you hear more of the subtleties and nuances. The car will ride mostly the same but feel more solid, more in control, less vague. You feel more of the roads texture. Tip: the installation will be much easier if you remove the brake rotors - less chance you'll cut the ball joint boots. PT Cruiser owners: take this opportunity to replace the ball joint boots. $8 each and they just pry off and press on. |
| Front Control Arm Bushings - Part Number: 4214 Customer: Dan Szorc Rating: 5 out of 5Overall Opinion: Awesome The rear end on my SRT4 would sway when going over bumps and potholes. These bushings fixed that issue right away. I would recommend installing these as well as prothane trailing arm bushings. |
| Front Control Arm Bushings - Part Number: 4214 Customer: Blair Mansfield Rating: 5 out of 5Overall Opinion: So far so good. I could notice a difference right away. Even my mechanic was impressed. I'm anxious to see how they hold up in our Canadian winters. |
| Front Control Arm Bushings - Part Number: 4214 Customer: Johnnie Blount Rating: 5 out of 5Overall Opinion: NICE! What a great product. It was easy to install and they shipped to me quick. I will buy from here again. |
| Front Control Arm Bushings - Part Number: 4214 Customer: richard bryant Rating: 5 out of 5Overall Opinion: VERY NICE Had some other bushings in that clunked really badly. No noise with these. Would buy again! |
| Front Control Arm Bushings - Part Number: 4214 Customer: Brian Kirby Rating: 5 out of 5Overall Opinion: Prothane Control Arm Bushings, 03 PT Cruiser I had previously installed some Lower Control Arm bushings in the past that had a three piece design with a rigid ring in the vertical bushing portion. After some pothole hits and some rough roads, they failed. I replaced these with the Prothane 2 piece design and the install was much simpler. The 2 piece design looks to be a bit less prone to pinching and binding as well. Looks to be a good product. |
| Front Control Arm Bushings - Part Number: 4214 Customer: Matt Dessecker Rating: 5 out of 5Overall Opinion: Excellent Parts Youll Never Regret Buying!!! I bought the Prothane control arm bushings for my Wife's 05 Dodge Neon SXT because the stock bushings on these cars are known to dry rot and wear out too soon. I figured that if I was going to have to replace them, I might as well go with ones that will pretty much be permanent. It probably took me a couple hours to get both sides installed, but it was all worth it. No more squeaking or thumping when entering parking lots or driveways. The front end definitely feels tighter and the car also handles better. Also a slight shudder in the tranny when it shifted from 3rd to 4th gear completely went away. Thanks to Prothane for a great product. I made sure that I used all of the grease that came with the new bushings because of reading about urethane bushing squeaks. I install the bushings approx. 5 months ago, and they are still quiet as a mouse. I'd recommend Prothane control arm bushings to ANYONE who is going to be replacing theirs!!! DO IT RIGHT THE FIRST TIME!!! |
 | Front Control Arm Bushings - Part Number: 4215 Customer: david studebaker Rating: 5 out of 5Overall Opinion: Worked out great. No need to worry about rotting rubber bushing that gives away the lower control arm. Bushing is a snap to install too thanks guys |
| Front Control Arm Bushings - Part Number: 4215 Customer: Jerry Keltner Rating: 5 out of 5Overall Opinion: quality stuff after installation and alignment the car drives and handles like it never has before all the klunks, pops and bangs are gone and a nice tight feeling front end. |
 | Front Control Arm Bushings - V10 and Diesel - Part Number: 4216 Customer: Alan Williams Rating: 5 out of 5Overall Opinion: very good quality great fit Installed in factory arms no problem just be careful if using a press. The factory arms bend very easy. Kit came with upper and lower arm bushings and more than enough lube. Have at least 2k miles on rig since install and not one complaint. Stock 1994 12v Ram 2500 4x4 |
 | Rear Control Arm Bushings - Part Number: 4301 Customer: Robin Boomsma Rating: 4 out of 5Overall Opinion: This is the third set of these bushings we have used on two Neons, on an autoslalom car and the other a short track oval car. We had to replace the short track car after a late season crash, and elected to build up a complete spare set of rear control arms/ bushings to have on hand if required for damage repair. In both applications, these parts have performed well. The only suggestion I would make is with respect to the inner rear bushings which fit the factory toe-in adjuster cam. The cam is not solid all the way around so I would like to see a metal sleeve insert between the cam and the urethane bushing. Robin Boomsma |
 | Rear Control Arm Bushings - Part Number: 4304 Customer: John Innocenti Rating: 5 out of 5Overall Opinion: They work great Product fit like a glove, nice the way the back is cupped. Not hard to put in. Plenty of grease to go around. Would recommend to anybody. Thanks for something that works great.
|
 | Front Sway Bar Endlinks - Part Number: 4401 Customer: Daniel Harrison Rating: 5 out of 5Overall Opinion: Very good, high quality, sway bar end links. It handles great and no poly noise. |
| Front Sway Bar Endlinks - Part Number: 4401 Customer: Dan Kuikman Rating: 5 out of 5Overall Opinion: excellent product!! Great product |
 | Rear Sway Bar Endlink Bushings - Sport package only - Part Number: 4402 Customer: William T Tarleton Rating: 5 out of 5Overall Opinion: very nice This plus the swaybar bushings made a big difference even with the stock rear bar. Not easy to install unless you have a press or a large vice. |
 | Rear Sway Bar Endlink Bushings - Part Number: 4403 Customer: THOMAS B ALEXANDER Rating: 5 out of 5Overall Opinion: GOOD AS YOU CAN GET REPLACED BUSHINGS INSTALLED 100K MILES AGO. RESTORED CRISPNESS AND STABILITY. CAN'T BEAT QUALITY PARTS. |
 | Motor Mount Inserts - Front - Part Number: 4501 Customer: Kevin Trimpey Rating: 5 out of 5Overall Opinion: very good part these inserts have helped my shifts in my car to be crisper and better, as an added effect, the motor mount will not break (i've gone through 3 in 2 years). this product has done wonders for me and my car. well worth the money. |
 | Rear Shackle Bushings - 7/8 Inch - Part Number: 4801 Customer: BRENT WILLIAMS Rating: 5 out of 5Overall Opinion: The bushings were used in the front eye of leaf springs on a straight axle on a 55 Chevrolet. The bushings seem to be working out nicely. |
| Rear Shackle Bushings - 7/8 Inch - Part Number: 4801 Customer: william mikolajchak Rating: 5 out of 5Overall Opinion: excellent replacement I got these parts as a replacement for my golf carts front suspension.I use the cart for farm and hunting. They were a very close match to the size i needed and were urethane not rubber. The original rubber ones were garbage and lasted only a few suspension cycles before they were trashed. I got these urethane parts and have since not had to worry about them. Great product and website. William |
| Rear Shackle Bushings - 7/8 Inch - Part Number: 4801 Customer: chris lasko Rating: 5 out of 5Overall Opinion: 10-10 Used with 89 wrangler and i took a dremel to the middle to make overall diameter around .960 to fit a center rod. They work great! with stock leafs. |
| Rear Shackle Bushings - 7/8 Inch - Part Number: 4801 Customer: FRANK M FUENTES JR Rating: 5 out of 5Overall Opinion: GREAT They fit perfectly as advertized and work just fine. |
 | Rear Shackle Bushings - 1 Inch - Part Number: 4802 Customer: Stephen Waite Rating: 5 out of 5Overall Opinion: Good Quality for the money Parts went together better than I had expected.I would certainly order from you again. |
| Rear Shackle Bushings - 1 Inch - Part Number: 4802 Customer: paul zimmer Rating: 5 out of 5Overall Opinion: Great product Parts were great and the service was even better. Thanks |
 | Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 61001 Customer: Alan Esterly Rating: 5 out of 5Overall Opinion: Excellent parts and service I ordered bushings for an old truck I was working on. The part I ordered was not available, but I received a call the next day and they offered me a different brand instead. The one they offered actually had a better warranty. I got the bushings quickly and had them installed the next day. thank you for your communication and getting the correct bushings to me. |
 | Rear Leaf Spring Bushings - Common Type - Part Number: 61007 Customer: mr marchant Rating: 5 out of 5Overall Opinion: great to deal with awsome product Great service. They were a pleasure to deal with. Product was just as described. |
 | Front Leaf Spring and Shackle Bushings - 1-1/4 Inch Main Eye - Part Number: 61009 Customer: brandon Rating: 5 out of 5Overall Opinion: 1967 ford front leaf spring bushings Picked up these bushing for the front of my truck and wow, fitment was good and tight. Worst part of the install was taking the old rubber bushing out. I'm very happy with this product. |
 | Front Leaf Spring Bushings - 2 Inch Spring Eye - Part Number: 61012 Customer: Dave M.Heard Rating: 5 out of 5Overall Opinion: Excellent Product Quality parts |
| Front Leaf Spring Bushings - 2 Inch Spring Eye - Part Number: 61012 Customer: sean hazzard Rating: 5 out of 5Overall Opinion: great product Easy installation, much better than oem |
 | Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 61018 Customer: Erik Aberly Rating: 5 out of 5Overall Opinion: Excellent Great product!! Fitment was great and arrived early, cant ask for much more than that!! |
| Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 61018 Customer: Adam Arnold Rating: 5 out of 5Overall Opinion: Perfect fit. Nice feel Popped them in with a c clamp and a flat piece of metal. Fit perfectly |
 | Rear Leaf Spring and Shackle Bushing - with Molded Shackles - Part Number: 61020 Customer: charles york Rating: 5 out of 5Overall Opinion: awesome I have them installed they were a perfect fit better quality than OEM for sure and will out last the truck I put them in. Thank you for your product |
 | Body Mount Bushings - 4WD - Part Number: 6105 Customer: Brendan St Jack Rating: 5 out of 5Overall Opinion: Parts are perfect,Great service 2 Good to deal with. Parts are just what I'm after. |
| Body Mount Bushings - 4WD - Part Number: 6105 Customer: Paul Rating: 5 out of 5Overall Opinion: Great Part came in about 10 days, delivery was updated by email. Very pleased. |
| Body Mount Bushings - 4WD - Part Number: 6105 Customer: alec schubel Rating: 5 out of 5Overall Opinion: Liked They worked and great fit. |
 | Rear Leaf Spring Eye and Shackle Bushings - 9/16 ID Shackle - Part Number: 61052 Customer: stephane Rating: 5 out of 5Overall Opinion: Great product, fit perfectly on my car I'm surprise to see how good the bushings fit. Seem very solid too. |
| Rear Leaf Spring Eye and Shackle Bushings - 9/16 ID Shackle - Part Number: 61052 Customer: Mike Spreitzer Rating: 5 out of 5Overall Opinion: very good fit perfect, easy install,good quality,wish all aftermarket parts fit like this,could use a little bigger tube of lube |
 | Body Mount Bushings - Part Number: 6106 Customer: nathan kissack Rating: 5 out of 5Overall Opinion: Realy good product They could have been a little longer they were a 1/2" shorter then my stock ones but are still a really great body mount |
| Body Mount Bushings - Part Number: 6106 Customer: Todd Turner Rating: 5 out of 5Overall Opinion: Great product Very easy to install. Haven't driven Truck yet to know how well the ride but very impressed. |
 | Body Mount Bushings and Radiator Support Bushings - Part Number: 6108 Customer: Ryan lafrancois Rating: 5 out of 5Overall Opinion: Great product made the truck drive ten times better than stock Good product, I'd buy it again. I probobly will too. |
| Body Mount Bushings and Radiator Support Bushings - Part Number: 6108 Customer: John R. Maloney Rating: 5 out of 5Overall Opinion: Just what I needed. Thanks John |
| Body Mount Bushings and Radiator Support Bushings - Part Number: 6108 Customer: Jarrett Nelson Rating: 2 out of 5Overall Opinion: Not what I had hoped I got this part to install on a 93 f350 since I had a bad body mount. I installed just the rear two since they were the only bad ones. I was hoping this part would line up the body lines between my bed and body but the mounts were taller than factory so now my cab sits higher than my bed instead of lower. In addition this taller height made them tougher to install. If I had to do it again I would just go with factory ford body mounts. |
| Body Mount Bushings and Radiator Support Bushings - Part Number: 6108 Customer: robert stenlund Rating: 3 out of 5Overall Opinion: good product Friday 12 October 2012,Australia.Just unpacked the bushes to install them only to find the rear cab bushes haven't got the metal insert around the inner diameter,making them too loose in the location holes.I'm going to attempt to fit rings to both rear cab mounts,if i cant ill have to try to buy two rear bushes with the rings,regards Bob. |
| Body Mount Bushings and Radiator Support Bushings - Part Number: 6108 Customer: Gregory A Cook Rating: 5 out of 5Overall Opinion: very good These are a great improvement over the stock bushings. We would by them again. |
 | Body to Frame Mount and Radiator Support Bushings - 2WD - Part Number: 6110 Customer: Wayne Abel Rating: 5 out of 5Overall Opinion: very good quality Good quality product, but would rather have paid extra, and have the kit include the sleeves. Have not fitted yet as trying to procure the right sleeves. |
| Body to Frame Mount and Radiator Support Bushings - 2WD - Part Number: 6110 Customer: Michael Kinkead Rating: 5 out of 5Overall Opinion: ease of installment Great product. |
| Body to Frame Mount and Radiator Support Bushings - 2WD - Part Number: 6110 Customer: Corey Rating: 4 out of 5Overall Opinion: Good stuff I think these are a great upgrade from stock rubber. I just wish it was offered with new steel sleeves. The stock 66 stuff is about impossible to get out if its even a little rusty. Overall they are good. Just have to make your own sleeves |
 | Sway Bar Bushings - 7/8 Inch - Part Number: 61104 Customer: Michael J. Duchac Rating: 5 out of 5Overall Opinion: good good quality. It would be better if you offered the entire kit along with the radius arm bushings though. I had to order a separate OEM Kit in order to use your bushings. |
 | Sway Bar Bushings - 7/8 Inch - Part Number: 61111 Customer: GREGORY E MARCHBANKS Rating: 5 out of 5Overall Opinion: gem_6421@hotmail.com I was impressed with the quality and the design engineering of the poly bushings. It is far better than the top competitors of Prothane, Motion and OEM. However, other competitors do include the hardened washers that go on the top and bottom of the stud end poly bushings and most buyers would not mind paying a few dollars more to have these included. When you omit these, buyers then have to stop, drive to a local fastener retailer and purchase these separately and this is inconvenient. I still give this product a 5 overall based solely on the poly pieces. Also, installation instructions either online or in package would be helpful and an increase in size of lube packet. Thank you, I will continue to use Prothane Motion products and recommend to others.......GM |
 | Rear IRS Subframe Bushings - Part Number: 6112 Customer: Andy Gottschalk Rating: 5 out of 5Overall Opinion: good products that fit well It is a lot of work to remove the old bushings but, the new parts are good products that fit well. |
 | Front Sway Bar and Endlink Bushings - 30mm - Part Number: 61130 Customer: Warren Hargrave Rating: 5 out of 5Overall Opinion: Grerat up-grade I thought new front shocks were needed, until I installed my new Sway bar bushing on my f250 1998 model /61130 I noticed my stock bushing were really Soft & Lose after removing them, my truck has only 44K on it. I have installed these bushings on past cars but must admit this was a huge improvement over other application I have tried them on! It took me about 90 minutes, as I took my time to clean and get things even. Love them, no need for a rear sway bar now. Warren |
 | Front Sway Bar and Endlink Bushings - 1.430 Inch - Part Number: 61131 Customer: Jarrod Burke Rating: 5 out of 5Overall Opinion: Far superior to oem Great replacement parts. Love the chromate coating. Much better then the oem part. Great service too by the way. Also very competitive price including postage. Keep it up guys! JRD MOBILE MECHANICAL Narangba, Brisbane, Australia |
 | Rear Sway Bar and Endlink Bushings - .765 Inch - Part Number: 61132 Customer: john bryce Rating: 5 out of 5Overall Opinion: Very impressed Parts have been installed, more than pleased with overall service and parts. Thank you J.Bryce |
 | Front Sway Bar Bushings - 29mm - Part Number: 61136 Customer: Robert Bushatz Rating: 5 out of 5Overall Opinion: Hard to find part for 1996 Mustang Cobra They fit perfect and got back old feel of car |
 | Front Sway Bar Bushings and Endlinks - 33mm - 4WD - Part Number: 61138 Customer: Daniel Breitkreuz Rating: 5 out of 5Overall Opinion: Perfect poly parts for the perfect price! Great product works like a charm! |
 | Rear Sway Bar and Endlink Bushings - 22mm - 4WD - Part Number: 61143 Customer: Daniel Breitkreuz Rating: 5 out of 5Overall Opinion: Once again perfect poly bushings! Fit perfectly! Great service and great price thanks guys! :) |
| Rear Sway Bar and Endlink Bushings - 22mm - 4WD - Part Number: 61143 Customer: Rejean Guay Rating: 5 out of 5Overall Opinion: good product at unbeatable price This seller is very fast to ship items and it was easy to find the exact product I need for my 2000 Ford Expedition. The part meet with the factory install suspension part. Thanks to this seller. I will do business again with this seller.. |
| Rear Sway Bar and Endlink Bushings - 22mm - 4WD - Part Number: 61143 Customer: John f Pettry sr Rating: 5 out of 5Overall Opinion: GREAT REPLACEMENT PARTS I USED THESE BUSHING,S ON MY EXPEDITION AND MAN WHAT A DIFFERENCE THEY MAKE IN THE RIDE AND HANDLING.THE END LINK BUSHING ARE A BREEZE TO CHANGE. ABOUT 45 MIN, TOTAL.THE SHIPPING WAS FAST.THANK,S |
 | Body Mount Bushings - Standard and Crew Cab - Part Number: 6115 Customer: Jason Dolynchuk Rating: 5 out of 5Overall Opinion: Hi, the parts have been installed, everything fit fine, the only thing was that there were no instructions and there were a couple of bolts close in length and where a little bit difficult to determine where they went. It feels stiffer in the cab and you can feel more of the bumps. Other than that, great product so far! |
 | Front Sway Bar and Endlink Bushings - 1 Inch - Part Number: 61151 Customer: nick oakley Rating: 5 out of 5Overall Opinion: HELLO GRAHAM, I AM GLAD THAT YOU SENT THIS ENQUIRY, I DID NOT FIND THE BUSHES EASY TO INSERT ,FIRSTLY , THE MATERIAL WAS VERY INFLEXIBLE ....NOT LIKE RUBBER. IN ORDER TO INSERT THE BUSHES I HAD TO CUT AWAY THE LEADING SHOULDER . A VERY TIGHT FIT THEIR AFTER. WHEN EVENTUALLY INSERTED I HAD TO REAM OUT THE INTERNAL HOLE IN ORDER FOR THE SWAYBAR TO BE INSERTED .......NOT AN EASY JOB , BUT NOT IMPOSSIBLE WITH THESE MODIFICATIONS . THANX FOR YOUR CONCERN ....NICK MY FORD E350 IS 1995 ECONOLINE WITH FLEETWOOD MONTARA MOTORHOME CONVERSION |
| Front Sway Bar and Endlink Bushings - 1 Inch - Part Number: 61151 Customer: Bill Holzem Rating: 4 out of 5Overall Opinion: Good product - Tough install Had a tough time getting the lower bushings pressed into the sockets - once in they should hold up well as these are some tough bushings. I would recommend them but patience is required to get them installed. |
| Front Sway Bar and Endlink Bushings - 1 Inch - Part Number: 61151 Customer: Ralph Lastoria Rating: 5 out of 5Overall Opinion: Awesome! Once the factory sleeves were removed from the I-beams. The new Prothane stabilizer bar bushings went right in, with a little work. But what a huge difference they made in the handling of a already difficult to control vehicle! I highly recommend these to anyone, never go back to standard rubber bushings again! |
 | Rear Sway Bar Bushings and Endlinks - 20mm - Part Number: 61153 Customer: Sylvester Stoute Rating: 5 out of 5Overall Opinion: my car rides like a brand new vehical i will surely shop with u guys |
| Rear Sway Bar Bushings and Endlinks - 20mm - Part Number: 61153 Customer: Kyle Steward Rating: 5 out of 5Overall Opinion: Perfect fit Great replacement for worn stock bushings. fit just like the old ones. great improvement to ride. |
 | Rear Sway Bar Bushings - 25mm - Part Number: 61157 Customer: ERIC SIMPSON Rating: 5 out of 5Overall Opinion: Two thumbs up As a returning customer I figured Energy would have what I needed to get my car right. My 03 Cobra has Energy bushings from front to rear and the bushing make a big difference in handling and cornering. Thanks Eric S. |
 | Body Mount Bushings Kit Sport Trac - Part Number: 6116 Customer: Stephen Ridolfi Rating: 4 out of 5Overall Opinion: No part numbers on product The only problem I found was the bushings did not have part numbers on them, but the instructions talked about part numbers. It was a little difficult matching and placing parts.Overall the bushings work they way they were suppose too. |
| Body Mount Bushings Kit Sport Trac - Part Number: 6116 Customer: Joseph G Salinger Rating: 5 out of 5Overall Opinion: Very good numbers on pads were almost unintelligible....Set included all but the rear body mounts which were the first to be recognized to need replacement.... So actually set incomplete..... |
| Body Mount Bushings Kit Sport Trac - Part Number: 6116 Customer: Firman Sakir Rating: 5 out of 5Overall Opinion: very satisfied They all worked perfect. These bushing are a better design than the OEM bushing. I plan on purchasing another set for my wife's vehicle. |
| Body Mount Bushings Kit Sport Trac - Part Number: 6116 Customer: Scott MacKenzie Rating: 5 out of 5Overall Opinion: Very good fit Loosening the bolts to get the old bushings out was definitely the most difficult part of the replacement. Once loosened, the new bushings slid in place perfectly. All squawks and squeaks are gone. Old bushings simply fell completely apart. The only thing I could see to make these better would be to make the part number impression more legible. |
| Body Mount Bushings Kit Sport Trac - Part Number: 6116 Customer: Donald Rodriguez Rating: 5 out of 5Overall Opinion: very sastified I recently installed these body mount bushings on my 01 Sport Trac. I am very pleased with the bushings, after fighting to get the bolts out then separating the washers the installation was a breeze. The only downside to the bushings were the casting numbers. They were not stamped into the bushings enough and hard to read, some of them had no number on at all. But as far as the bushings I am very sastified and would recommend them to everyone. The ride has improved a lot along with the ride height, and I don't have to worry about them deteriorating like the factory ones did. Thank you for a great product. |
| Body Mount Bushings Kit Sport Trac - Part Number: 6116 Customer: Manuel Vidal Rating: 5 out of 5Overall Opinion: Excellent The product is excellent and fit perfectly. The price super, you cant ask for more. The shipping was fast, I ordered and 2 days later at my door step. I would recommend to all my friends. |
| Body Mount Bushings Kit Sport Trac - Part Number: 6116 Customer: Richard Adams Rating: 5 out of 5Overall Opinion: Exactly what you said it was In stalled parts as per instruction provided. fit is great no noise much better than stock. |
| Body Mount Bushings Kit Sport Trac - Part Number: 6116 Customer: Cesar Feliu Rating: 5 out of 5Overall Opinion: simple ! like it very simple thanks :) a+ |
 | Front Sway Bar Bushings - 34mm - Part Number: 61161 Customer: David Gonzales Rating: 5 out of 5Overall Opinion: Great product ! The bushings fitted perfectly and were pre- slitted to allow them to be installed without disconnecting all of the front sway bar attachments to the wheel struts. |
 | Front Sway Bar Bushings - 28.6mm - Part Number: 61164 Customer: Jorge I. Ortega Rating: 5 out of 5Overall Opinion: Exelent It fits perfect, excellent quality, it solve mi problem better than I expected. |
 | Front Sway Bar and Endlink Bushings - 32mm - 1.5 Inch Endlink Eyes - Part Number: 61166 Customer: Melissa Stocker Rating: 5 out of 5Overall Opinion: I was very happy with my purchase!!!!! |
| Front Sway Bar and Endlink Bushings - 32mm - 1.5 Inch Endlink Eyes - Part Number: 61166 Customer: John Ciolli Rating: 5 out of 5Overall Opinion: The quality & performance is exactly as expected! Would have liked a more detailed set of instructions. Even though the link you sent me was very helpful. I was still unable to remove the stock Ford bushings using a hydraulic press. They had to be practically burned out w/a torch. Once everything was cooled & cleaned it went together perfectly w/the new parts & perform flawlessly. Very well made parts. |
| Front Sway Bar and Endlink Bushings - 32mm - 1.5 Inch Endlink Eyes - Part Number: 61166 Customer: Raymond Hogan Rating: 5 out of 5Overall Opinion: The parts were great, and easy to install. Delivered with speed. Thanks again, Raymond |
| Front Sway Bar and Endlink Bushings - 32mm - 1.5 Inch Endlink Eyes - Part Number: 61166 Customer: David Zozaya Rating: 5 out of 5Overall Opinion: very good product, no more squeals and installs very well. Great product, I just had to order the 36mm bushings for my application. I had the bigger sway bar and the 32mm bushings with the kit were a little too small for a good fit. Still no complaints, I am very glad I changed the bushings. |
 | Front Strut Arm Bushings - Part Number: 61204 Customer: Casey Painter Rating: 5 out of 5Overall Opinion: item just as described I decided not to use these bushings on my strut rods due to the non-flex characteristics of the polyurethane. After carefully reviewing these, I decided to go a different route. |
| Front Strut Arm Bushings - Part Number: 61204 Customer: William Serene Rating: 5 out of 5Overall Opinion: Great Parts, Easy to Install I could easily feel the difference, Thank you |
 | Front Strut Rod Bushings - 2 Piece Design - Part Number: 61205 Customer: Jon Hurst Rating: 5 out of 5Overall Opinion: Quality parts The stiffer the material here, the more the sway bar gets to operate the way it was designed. I have no doubt my front end feels right because of using good parts like these. |
| Front Strut Rod Bushings - 2 Piece Design - Part Number: 61205 Customer: Michael Linke Rating: 5 out of 5Overall Opinion: Bit of a delay to get part but overall I'm happy. Hope to get future parts quicker. The part itself is great. |
| Front Strut Rod Bushings - 2 Piece Design - Part Number: 61205 Customer: Daniel Green Rating: 5 out of 5Overall Opinion: Good quality, fit application properly I had just rebuilt the front suspension of my car when a set of Master Ride strut rod bushings squeezed right out. Just after the front end was aligned. Not even 20 miles on the vehicle. So far your product is doing very well and I am impressed. Thank You. |
| Front Strut Rod Bushings - 2 Piece Design - Part Number: 61205 Customer: Frank Adkins Rating: 5 out of 5Overall Opinion: Excellent I had installed Moog rubber bushings in a customers car, but nowadays apparently Moog bushings are of substandard quality. Marshmallow soft, they failed and broke apart within two months of occasional driving. I replaced them with Prothane urethane bushings, and they work remarkably well. My customer is extremely happy, and that makes me happy. |
| Front Strut Rod Bushings - 2 Piece Design - Part Number: 61205 Customer: paul hosking Rating: 5 out of 5Overall Opinion: perfect product fit just rite Perfect product, fit how they should. No problems, easy to install, recommend to anyone restoring a car to use these products |
 | Front Strut Arm Bushings - Part Number: 61206 Customer: Delbert L Brown Rating: 5 out of 5Overall Opinion: Very pleased Fit was perfect and shipping was quick. The price was also much lower than other stores. |
 | Radius Arm Bushings - Part Number: 61207 Customer: Jesse Dale Gibson Rating: 5 out of 5Overall Opinion: Great Parts installed easy as can be. Front suspension is very happy! Thank you! |
| Radius Arm Bushings - Part Number: 61207 Customer: Donald M Ricks Rating: 5 out of 5Overall Opinion: Easiloy mounted bushings The super grease sent with another order (axle bushings) helped a lot to keep them together in the 1971 Ford F-100 I-beam axle, and what was left over to install my radius arm bushings. Great parts and great grease. Haven t driven my truck with them on but expect they will ride better than the old rubber bushings. |
| Radius Arm Bushings - Part Number: 61207 Customer: Chris Varcoe Rating: 5 out of 5Overall Opinion: Very good Tougher than the original rubber and colored in plain black, they do the job perfectly. |
| Radius Arm Bushings - Part Number: 61207 Customer: Eric SCULFORT Rating: 5 out of 5Overall Opinion: Material ok and easy to mount Item is perfect fit and easy to mount. It is for a ford bronco 1979 with a BBF 460 in instance to be completely rebuild here in Belgium. |
 | Front Track Arm Bushings - Round Type - Part Number: 61208 Customer: Steven Wagner Rating: 5 out of 5Overall Opinion: good Installed as expected, seems to be quality product. |
 | Front Radius Arm Bushings - Part Number: 61210 Customer: carl vincent Rating: 5 out of 5Overall Opinion: great fit Perfect fit, fast delivery. Good product |
| Front Radius Arm Bushings - Part Number: 61210 Customer: Bolivar Rosado Rating: 5 out of 5Overall Opinion: It fit great !!!!!! Thanks Again; You have the perfect parts at the best price. |
| Front Radius Arm Bushings - Part Number: 61210 Customer: Albert Cole Rating: 5 out of 5Overall Opinion: Very good quality and fitment. Excellent product quality and perfect fit. These were easier to install than I thought. I basically ignored the manual for my explorer and ground off the 4 rivets. Much easier and faster. No more knocking! |
| Front Radius Arm Bushings - Part Number: 61210 Customer: Genevieve Lacoste Leger Rating: 5 out of 5Overall Opinion: good stuff Thanks for your good service and you have a good stuff!!! |
| Front Radius Arm Bushings - Part Number: 61210 Customer: Tonia Colon Rating: 5 out of 5Overall Opinion: great product Part's great quality, fit like a glove, and I really like them in red thanks |
| Front Radius Arm Bushings - Part Number: 61210 Customer: Curtis Hatfield Rating: 5 out of 5Overall Opinion: Great products I bought 1 set of Front Radius Arm Bushings Part Number: 61210 and they improved the handling and ride of my truck, so much so that bought another set for my other truck. Great products and great prices. |
 | Front McPherson Strut Tower Bushings - Part Number: 61213 Customer: Richard Lavocat Rating: 5 out of 5Overall Opinion: Great product THEIR IN, GOOD FIT, NO MORE NOISES AND MY LITTLE RED GT HUGS THE ROAD AS TIGHT AS A HUG FROM MOM. THANKS OLCAT |
| Front McPherson Strut Tower Bushings - Part Number: 61213 Customer: Alex Ocariz Rating: 5 out of 5Overall Opinion: Outstanding I ordered struts for my ford mustang and the struts did not include replacement bushings. I found these and the price was right. The bushings arrived within a few days after the order was complete and fit like a glove. |
 | Front Strut Rod Bushings - Part Number: 61214 Customer: John R. Russell Rating: 5 out of 5Overall Opinion: Well made quality parts These parts look like they are well made and fit correctly. They needed no modifications or trimming, they fit right in. The description and picture were good so I knew what I was getting which is Important since there is quite a lot of tear down and the expense of an alignment involved. You had the parts in stock and they came quickly. |
 | Front Track Bar Bushings - 15.5mm Bolt - Part Number: 61217 Customer: Raymond F Fink Rating: 5 out of 5Overall Opinion: Much better than factory original It was more work to get the old bushings out than it was to install the new, split design. This part shored up the tracking problem, and appears very durable. Fast shipping and wide availability will have me coming back. --Fink |
| Front Track Bar Bushings - 15.5mm Bolt - Part Number: 61217 Customer: Jesse H. Franklin Rating: 3 out of 5Overall Opinion: good bushings, wrong truck Bushings are great, to my understanding they're for a early 99 f250. Well, they didn't fit my early 99 f250. They are for a late 99-03 truck but listed as early 99 parts, I don't know if it was my mistake or yours. But, they are great bushings |
| Front Track Bar Bushings - 15.5mm Bolt - Part Number: 61217 Customer: John Bergman Rating: 5 out of 5Overall Opinion: Great product A big improvement over the worn out stuck bushings. Very easy to install. |
| Front Track Bar Bushings - 15.5mm Bolt - Part Number: 61217 Customer: rl nix Rating: 5 out of 5Overall Opinion: GOOD, Parts fit right, much cheaper than replacing whole dang track bar. Good product. |
| Front Track Bar Bushings - 15.5mm Bolt - Part Number: 61217 Customer: James Taylor Rating: 5 out of 5Overall Opinion: Great Parts!!! Parts fit with ease and work great! |
| Front Track Bar Bushings - 15.5mm Bolt - Part Number: 61217 Customer: jerry jones Rating: 5 out of 5Overall Opinion: GOOD Parts look like an improvement over OEM, although time will tell. It would have been nice if there had been mention of needing a press to remove the old ones. |
| Front Track Bar Bushings - 15.5mm Bolt - Part Number: 61217 Customer: william wendt Rating: 5 out of 5Overall Opinion: The parts were shipped with fast. The bushings were designed for larger bolts which was great because the holes in the frame were a little enlarged so after machining the holes to accept larger bolts the new bushings were tight and solid. |
| Front Track Bar Bushings - 15.5mm Bolt - Part Number: 61217 Customer: Mike Praegitzer Rating: 5 out of 5Overall Opinion: Great product much better than stock part. Great product, easy to install. Superior to the stock bushings, highly recommend to anyone looking for a noticeable suspension improvement. |
| Front Track Bar Bushings - 15.5mm Bolt - Part Number: 61217 Customer: Doug Mallory Rating: 5 out of 5Overall Opinion: Easy Install Easy install after getting the old bushings out. The old ones had to be pressed out. |
| Front Track Bar Bushings - 15.5mm Bolt - Part Number: 61217 Customer: CHASE Rating: 5 out of 5Overall Opinion: VERY GOOD PRODUCT FIT PERFECT. VERY GOOD |
 | Front Track Bar Bushings - 21.5mm Bolt - Part Number: 61218 Customer: Glenn LaRocco Rating: 5 out of 5Overall Opinion: Good product A+++ good product installed with ease , would recommend to anyone Thank you |
| Front Track Bar Bushings - 21.5mm Bolt - Part Number: 61218 Customer: John Potter Rating: 5 out of 5Overall Opinion: Parts fit great, delivery was prompt, no complaints. |
 | Rear Bump Stop Kit - Part Number: 61301 Customer: DAVID TYLER Rating: 5 out of 5Overall Opinion: Very impressed I installed them the next day, they fit great and function great. |
 | Front Strut Bump Stops - Part Number: 61302 Customer: eduardo bianzon Rating: 2 out of 5Overall Opinion: After a month that I have installed it. 1 got shattered on the right suspension on my car. I was about to call and have it replaced. Thanks! |
 | Transfer Case Mounts - Part Number: 61601 Customer: Levi Campbell Rating: 4 out of 5Overall Opinion: Great parts for the money Good parts for an old truck |
| Transfer Case Mounts - Part Number: 61601 Customer: David Holden Rating: 5 out of 5Overall Opinion: holdenrock@aol.com These worked on my 69 F 250 highboy w/ Spicer Model 24 transfer case. Very pleased w/ prompt shipping and will do business here again. |
| Transfer Case Mounts - Part Number: 61601 Customer: Rab Rawlins Rating: 5 out of 5Overall Opinion: 5/5 My old bushings self destructed. I replaced them with these and a lot of my drive train chatter disappeared. I've used E.S. in the past and expect the same superb results from these! Solid 5 out of 5! |
| Transfer Case Mounts - Part Number: 61601 Customer: Michael C Yasuda Rating: 5 out of 5Overall Opinion: Excellent replacement parts Very happy with the product. Installation was very easy. Shipping was great. Have your site bookmark for future projects. |
| Transfer Case Mounts - Part Number: 61601 Customer: JAY JANSEN Rating: 5 out of 5Overall Opinion: good product The only problem I had was that no one knew if it would fit my 1977 F250 4x4 Highboy. I took a chance that it would work and it did. I will order a hole kit to replace all of the rubber parts in a while. Thank you again for a fine product. Jay Jansen |
| Transfer Case Mounts - Part Number: 61601 Customer: Ronald Czajkowski Rating: 5 out of 5Overall Opinion: Parts seemed to fit just like original on a 77 Ford 250 4X4 transfer case. Not sure why they only included 2 washers. Had to get 2 more to finish the job. |
| Transfer Case Mounts - Part Number: 61601 Customer: Russell Frey Rating: 5 out of 5Overall Opinion: Quality product, matches original equipment. This is the only place I was able to find these mounts. Fit perfectly into original place, no modification needed. |
| Transfer Case Mounts - Part Number: 61601 Customer: Jason Hurley Rating: 5 out of 5Overall Opinion: Good for the most part a great product. I was very happy with the fit of the bushings and it brought my transfer case back inline and held it up nice and tight. A quick trip to the hardware store fixed that problem. Overall a great product at a very good price. Thanks. |
| Transfer Case Mounts - Part Number: 61601 Customer: Jason M Lycans Rating: 5 out of 5Overall Opinion: Very satisfied These bushings were exact replacement parts with far superior quality. I will continue to purchase parts from your company in the future. |
| Transfer Case Mounts - Part Number: 61601 Customer: james napier Rating: 5 out of 5Overall Opinion: excellent product Got the parts fast, no BS. Repaired my truck in 3 hours. Old parts were non exisitant and the new ones fit perfect and now my truck drives like brand new. No shakes, vibration, just great. If you are thinking about this part, I would say what are you waiting for. |
 | Transfer Case Bushings - Part Number: 61602 Customer: Mauricio Mayorga Rating: 5 out of 5Overall Opinion: Worth the Price Items are as good as they get. I actually sold these and re=purchased a s set of the red bushings. I did that only due to the fact that I changed out all the bushings on the truck and they are all red, so I wanted them to match, more vanity than anything else. I think even if it is a bit more expensive, you should include the large HD washer that I had to purchase separately and the oddball auto size bolts too with all metal lock washers. The 40 year old hardware is always in need of replacement and not all hardware stores even the good one carry that size bolt in grade or like I use on all my suspension F911s or grade 9s. Instructions would be helpful. Though not requiring and MIT degree it can be frustrating for the novice. Fact that a floor jack and wood to reach up to the transfer-case will not be obvious to any who have not changed these out. The confines are really tight if you do not have a body-lift to access the top nut or head depending on if the they have been tampered with in the last 40 years. Little to no access from the top unless you cut an access hole in the tunnel. I was lucky and didnt have to remove my front drive-shaft as the upper cardan was almost impeding the bolt from coming out. Common tools are all that are need except for some sort of high reaching jack and wood. will be good for another 40 after they are changed. Heres a thought no one produces a poly transfer-case snubber, not sure if only the early broncos have that part, but I would love to be able to replace with poly, in fact I am looking into modifying some other of your mounts to fit in there, why not be the only producer of it? Best of luck, Good product...Mo |
| Transfer Case Bushings - Part Number: 61602 Customer: Peter Zinck Rating: 4 out of 5Overall Opinion: Good parts. better than the OE parts that I replaced. |
| Transfer Case Bushings - Part Number: 61602 Customer: Jack Goodwin Rating: 5 out of 5Overall Opinion: Very nice product! fit perfect. Very nice product! Fit perfect. Thanks for a product that works. Jack |
 | Mustang Transmission Crossmember to Frame Bushing Kit- 79-93 - Part Number: 61603 Customer: Sandra Fox Rating: 5 out of 5Overall Opinion: Fast shipping and part worked great Part worked great and was fast shipping and stayed on top of order also kept in contact with me the whole time to see if I received part yet. |
| Mustang Transmission Crossmember to Frame Bushing Kit- 79-93 - Part Number: 61603 Customer: Gerald Mueller Rating: 5 out of 5Overall Opinion: great I bought carquest motor mounts and trans. mount and the convertor hit the fire wall and the engine did not sit straight. I put Energy suspension mounts in and everything fit great with lots of clearance |
 | Transmission Mount - Part Number: 61605 Customer: Dennis Martin Rating: 5 out of 5Overall Opinion: Very good robust gearbox mount used on my v8 cortina. |
| Transmission Mount - Part Number: 61605 Customer: Larry Toews Rating: 5 out of 5Overall Opinion: great part This transmission mount is very nice. After trying to get one near an original one and getting junk metal with small weak rubber pads (all that is available from the aftermarket mount makers apparently) which is not even close in construction to the original OEM Ford piece, this urethane mount is one finely crafted piece. It fits perfectly and is in fact, close in appearance and construction to the original OEM mount, only better. Nice to find a good quality product. |
 | Front IRS Differential Bushings - Part Number: 61609 Customer: ken lenker Rating: 5 out of 5Overall Opinion: Stopped wheel hop on 03 cobra, will be using other bushings from Energy. |
| Front IRS Differential Bushings - Part Number: 61609 Customer: Michael King Rating: 5 out of 5Overall Opinion: Good Parts Simple removal and installation. This was the least of my problems on the Cobra rear end repair. |
 | Rear IRS Differential Bushings - Part Number: 61610 Customer: Michael King Rating: 5 out of 5Overall Opinion: Good Parts These bushings went in very tight. I have a small 12 ton press so it worked out well. I can't imagine installing by hand or c clamp. |
| Rear IRS Differential Bushings - Part Number: 61610 Customer: Andy Gottschalk Rating: 5 out of 5Overall Opinion: Parts fit well. Parts fit well. |
 | Rear Coil Spring Isolators - Part Number: 61701 Customer: Colin Warriner Rating: 5 out of 5Overall Opinion: Great Product 5-Stars All The Way I bought these coil spring isolators and they have performed great. No more squeaks and noises from my coil springs. My ride is smoother and quieter than ever before. If you're looking to buy some all I can say is for the price you pay you get 10 times your moneys worth. |
| Rear Coil Spring Isolators - Part Number: 61701 Customer: ken lenker Rating: 5 out of 5Overall Opinion: Great product |
 | Front Lower Spring Perch - Pair - Part Number: 61702 Customer: Harold Castaneda Rating: 5 out of 5Overall Opinion: The part was excellent and met my expectation. I would recommend this part to anyone looking to buy it. Top quality part. |
 | Front Coil Spring Isolators - Part Number: 61703 Customer: Colin Warriner Rating: 5 out of 5Overall Opinion: Great Product 5-Stars All The Way I bought these coil spring isolators and they have performed great. No more squeaks and noises from my coil springs. My ride is smoother and quieter than ever before. If you're looking to buy some all I can say is for the price you pay you get 10 times your moneys worth. |
 | Complete 14-Piece Kit - 2 Degree Offset C Bushings - Part Number: 61901 Customer: DOUGLAS RASMUSSEN Rating: 5 out of 5Overall Opinion: Very good ! FIT GOOD |
 | Total Kit - Part Number: 62001 Customer: Danny Hampshire Rating: 5 out of 5Overall Opinion: Parts came quickly and have been fitted. All good, thank you. |
 | Total Kit - Part Number: 62003 Customer: James Duvall Rating: 4 out of 5Overall Opinion: Ok, I guess.... I rate 5 for performance, 1 for instructions and 3 for ride. I decided on this product because Prothane's web site said they were formulated for both ride and performance. My mushy factory bushings were 14 years old and I was getting outer tire wear. The handling performance is terrific. I would have preferred polyurethane formulated more for ride as Mustang suspensions are pretty rough. The rear end doesn't hop anymore and the cornering is far more than you need on the street. The bushings have settled into place some and the noise level has dropped a little but I am going to need add some dynamat in areas where the arms connect to the body. The biggest problem was the lack of instructions. None were included and Prothane emailed me a set that were vague at best. Be warned that the front lower arm has two bushing types but both bushings were included. Some of the shells have inner sleeves that get left behind when the bushings are burned out. These must be removed. The bushings should not be hard to fit but the rear bushings were all too tight and had to be frozen and pressed in. I had to hone out the rear axle shells for the upper rear arm The kit doesn't include ball joint lower A arm dust covers which should be replaced for cars this age and buy new nuts for them since it is a big job to get the front springs back in place. You should also go ahead and buy rear axle lower arm bolts as they will all be frozen up (sledge and air hammer to get them out after removing the rear calipers for access). I didn't use the tie rod ends covers. |
 | Total Kit - Part Number: 62027 Customer: Jesse Morris Rating: 5 out of 5Overall Opinion: very good product These parts went in very smooth. Would of liked a little better description on what was what and where they went. But overall a really good product. |
 | Total Kit - Part Number: 62036 Customer: Michael Stock Rating: 5 out of 5Overall Opinion: Very Good Quality parts and a professional company I overhauled my 2002 F150 F4 Supercrew with this kit, replaced the shocks, worn out bearings, seals and linkage components, front and rear etc. The parts in the box were of high quality and the rubber had a nice firm durometer to it. I'm not sure it was equivalent to the OEM parts, but I was looking for a performance upgrade that included stiffer rubber. I installed the parts (and other elements) and now my truck runs better than it did when I purchased it over 10 years ago! Over time, I developed a moderate Bump-Steer issue (back end darts to one side when driving over bumps) that has completely vanished! Not that I would never consider driving above the speed limit, however, when exiting the Pike the other day, I leaned into the cover quite vigorously and my truck ran like it was on a slot car track - smooth, firm and it held tight all the way through the corner! Superb! If your truck has some miles on it and your not ready for an upgrade, I highly recommend a suspension overall that includes ENERGYSUSPENSIONPARTS.COM parts! They ROCK!! |
 | Front Control Arm Bushings - non HD - Part Number: 6205 Customer: Linda S Cooper Rating: 5 out of 5Overall Opinion: Nice Product Very good fit.. easy installation |
 | Front Control Arm Bushings - with HD - Part Number: 6206 Customer: Hubert Markley Rating: 5 out of 5Overall Opinion: very good Nice, no trouble installing them. |
 | Front Control Arm Bushings - non Hydro Lower Bushing - Part Number: 6207 Customer: Paul Johnson Rating: 5 out of 5Overall Opinion: Pretty Easy I made the mistake of ordering the wrong bushings for the rear of the A arm . They are the Hydro bushings . The front ones installed easily though . |
| Front Control Arm Bushings - non Hydro Lower Bushing - Part Number: 6207 Customer: luis ramos Rating: 5 out of 5Overall Opinion: great product, What you see is what you get. Great product, was able to feel difference in ride. |
 | Front Control Arm Bushings - Part Number: 6210 Customer: Tom Tinsman Rating: 5 out of 5Overall Opinion: very nice Had to machine upper control arm shafts for sleeves to fit. |
 | Front Control Arm Bushings - 2WD - Part Number: 6212 Customer: Joseph Bratton Rating: 5 out of 5Overall Opinion: I am sure the parts are of good quality, but they were not serviceable for my application. I believe I wrote (its been a while) that I wanted to install these in an aftermarket set of A arms and they are for stock applications only. Returning something most times is such a hassle that I did not bother.....It was not your fault I am sure..........thanks for asking. Joe |
 | Front Control Arm Bushings - Part Number: 6213 Customer: ricky j melichar Rating: 5 out of 5Overall Opinion: great The parts were perfect. |
 | Front Control Arm Bushings - Hydro - Part Number: 6217 Customer: Richard Rose Rating: 5 out of 5Overall Opinion: great bushings! and nice stiff ride! You can either press them out or burn them out. is the these are hydr these are hydro bushings and they ha and they have a special sleeve that comes in the bushing or you or your bushing will go i in will go in mushroomed. This is the problem I had once I realized that the sleeve needed to be removed. I removed the sleeve and all was well |
 | Rear Control Arm Bushings - Part Number: 6307 Customer: randy Symons Rating: 5 out of 5Overall Opinion: Far far better than OEM While everything was rust welded and had to be cut out these bushings were simple and easy to install. After a short drive I think my slot-car is back. It feels great to have the controlability of my car back, it was a scarey experience before hand as the old oem bushings were quite screwed up. These are a great product and will out last the car for sure. Thanx |
| Rear Control Arm Bushings - Part Number: 6307 Customer: Jason Lachapelle Rating: 5 out of 5Overall Opinion: quality feel and look Once the control arms are removed from the car, its all smooth sailing. All the outer shells were pressed in using a bench vise. The shells fit snugly in their bores in the control arms. The rest of the bushing assembles by hand. NOTE: You will likely need to use a hot torch on some of the original bolts. They rust-weld to the inner shells of the original bushings. |
| Rear Control Arm Bushings - Part Number: 6307 Customer: Donn Eliasen Rating: 5 out of 5Overall Opinion: good product Easy to install, dis-assembly was a struggle due to age of vehicle, but new bushings went in really well with a large vise as a press. Cheaper than buying replacement parts. |
| Rear Control Arm Bushings - Part Number: 6307 Customer: Chris Swan Rating: 5 out of 5Overall Opinion: Good Product The bushings were easy to install, the fit was good and they were delivered quickly. |
| Rear Control Arm Bushings - Part Number: 6307 Customer: Michael Stefanelli Rating: 5 out of 5Overall Opinion: Excellent product I bought this kit to get the bushings for the rear lower control arms on my 2000 ford focus. Because of broken(defective) coil springs on this car. I had to cut the bolts holding the lower control arm to the break drum knuckle in order to remove and replace the defective springs. The bolts had rusted solid to the lower control arm bushing. Dealer tried to tell me that the bushing were factory pressed in and could not be replaced(bull S#@!), wanted to sell me new control arm. Using the bushings from this kit and a press for changing ball joints, I easily pressed out the old bushings and pressed in the new ones. Thanks for making these parts available. Mike |
| Rear Control Arm Bushings - Part Number: 6307 Customer: thomas oliver Rating: 5 out of 5Overall Opinion: very good These parts were easy to install on the control arms and all bushings needed were in this kit. The parts were not easy to get off the car but that's old age and rust. I would definitely recommend these parts. It also saved me 400 buck or more thank for the help |
| Rear Control Arm Bushings - Part Number: 6307 Customer: Jean-Francois Garcia Rating: 5 out of 5Overall Opinion: easy to use and to install I found these products easy to use right from the box. I used them on a street car instead of replacing my original parts more expensive anyway and it is better. |
| Rear Control Arm Bushings - Part Number: 6307 Customer: James McKelvey Rating: 5 out of 5Overall Opinion: Bushings went together easy, no problems |
 | Rear Trailing Arm Bushings - Part Number: 6308 Customer: Karl Rating: 5 out of 5Overall Opinion: Not too hard, fits 2006 mazda 3 Cost less than Energy Suspension. Seems to be a bit softer but this fine when reusing the existing steel shells. Fit my 2006 Mazda 3S. Might fit other years. Finding Mazda parts can be a gamble at times... |
| Rear Trailing Arm Bushings - Part Number: 6308 Customer: Aaron Keck Rating: 5 out of 5Overall Opinion: Good Quality Product The product is quality made, matched the photos and descriptions advertised, and fit my application correctly (2008 Ford Focus SES Coupe). I was glad to see that it came with the Prothane bushing grease, especially that there was enough for a proper installation. The order was handled in a timely manner and shipped as expected. |
 | Rear Control Arm Bushing Axle Housing Kit - Part Number: 6309 Customer: Mark Lorenz Rating: 5 out of 5Overall Opinion: Great Fairly easy to install. Excellent quality and have had no problems with the parts. I'll use your parts again next time I need suspension components!! Thanks |
| Rear Control Arm Bushing Axle Housing Kit - Part Number: 6309 Customer: Jason Gauthier Rating: 5 out of 5Overall Opinion: Very satisfied with the item Hi, I haven't had time to install the bushings yet but I can say that they are of very good quality and wouldn't hesitate to recommend to others. And also thanks to EnergySuspensionParts.com for the fast shipping really enjoyed my shopping experience with you guys.. |
| Rear Control Arm Bushing Axle Housing Kit - Part Number: 6309 Customer: Robert washburn Rating: 5 out of 5Overall Opinion: well it said the would fit my mustang 82 ...5.0.. for what never reason i wasn't able to use them...so it was a waste of my money...but its not your fault...i order the wrong stuff all the time....but i had to use them for a few days until the right one came in..so i didn't try to return them..i will find someone to sell them to they race mustangs at our local track so it should be a problem.... |
 | Rear Control Arm Bushings - I.R.S. - Part Number: 6311 Customer: ken lenker Rating: 5 out of 5Overall Opinion: First class all the way |
 | Motor Mounts - 5.0 Engine Only - Part Number: 6501 Customer: HADJII STEVENS Rating: 5 out of 5Overall Opinion: MOTOR MOUNTS - 5.0 ENGINE FANTASTIC PRODUCT!!! I've used stock and H.D. replacements before and the just don't hold up to the punishment on road race courses. The vehicle is also street driven once in a while, so I didn't want solid mounts. I also have two sets now on SBC engines and they are great. Good price and great quality.
|
 | Motor Mount Inserts - Front Lower - Part Number: 6502 Customer: Noel Bustillos Rating: 5 out of 5Overall Opinion: surprisingly simple to install. :) I am impressed with the outcome of the durability of the parts. Driving the car is better and feels like I don't lose any power. Response time from gas pedal to to vehicle moving is great. Acceleration from 35 to 60 in 3rd gear IS much faster. Thank you so much. |
 | Axle Pivot Bushings - Part Number: 6601 Customer: Henry Anderson Rating: 4 out of 5Overall Opinion: OK experience While the quality of the Prothane axle pivot bushings are very good, the installation was a pain and their customer service was awful. They couldn't even tell me if I was installing the parts correctly or not. Replacing my old bushings with these I noticed a big improvement, but I think next time I might order from a different manufacturer. |
 | Axle Pivot Bushings - Cast Axle - Part Number: 6603 Customer: N Mortensen Rating: 3 out of 5Overall Opinion: Meh... Rather than having to burn the rubber out of the factory steel sleeve and reuse it, it would make more sense to just include a new sleeve (cheap rubber replacement bushings do!). |
 | Axle Pivot Bushings - Twin I Beam Models - Part Number: 6604 Customer: Denny Raines Rating: 5 out of 5Overall Opinion: High quality at a low cost! Quality made parts with easy to follow instructions. Very easy to install! |
| Axle Pivot Bushings - Twin I Beam Models - Part Number: 6604 Customer: Blake Hall Rating: 5 out of 5Overall Opinion: This product is a big improvement from the stock rubber bushings. My vehicle rides and handles a lot better. Even came with a small tube of grease I needed to install them. Very happy. |
| Axle Pivot Bushings - Twin I Beam Models - Part Number: 6604 Customer: Donald M Ricks Rating: 5 out of 5Overall Opinion: They went on easily The super grease sent with the parts helped a lot in both joining them together in the 1971 Ford F-100 I-beam axle. The parts went on easily, and they look good. I had cleaned the old rubber bushings out well and greased the remaining metal part, into which the bushings were inserted. I then mounted the axles myself. I believe these particular bushings will work well. Don't forget the super glue. I used what was left over to install my radius arm bushings. Great parts and great grease. |
| Axle Pivot Bushings - Twin I Beam Models - Part Number: 6604 Customer: William Kandis Rating: 5 out of 5Overall Opinion: Good product I found that the Prothane bushings were easy to install once you cut the old rubber ones out. They fit snug in the hole and the ride is great. |
 | Steering Rack Bushings - Part Number: 6701 Customer: Vincent Dominick Rating: 5 out of 5Overall Opinion: Great Product |
 | Steering Rack Bushings - Part Number: 6703 Customer: William Hanna Rating: 5 out of 5Overall Opinion: Excellent build quality, great fitment! These went in smoothly, had excellent build quality and completely changed the feel of the steering. Id recommend these to anyone. |
 | Steering Rack Bushings - Offset Style - For Lowered Cars - Part Number: 6704 Customer: Tom Williams Rating: 5 out of 5Overall Opinion: Quality product These bushings went in very well with minimal effort but not loose like some aftermarket stuff. My steering rack now sets level with the tie rods. After a few months of driving, everything still feels good. |
| Steering Rack Bushings - Offset Style - For Lowered Cars - Part Number: 6704 Customer: james russo Rating: 5 out of 5Overall Opinion: Very impressed Excellent part. Fit right in. |
 | Power Steering Bushings - Part Number: 6705 Customer: Marco Calderon Rating: 5 out of 5Overall Opinion: Very good quality parts. at an awsome price! Good product. Really good price. Recommended |
| Power Steering Bushings - Part Number: 6705 Customer: Randy Mackay Rating: 5 out of 5Overall Opinion: excellent, Great, highly recommend them |
| Power Steering Bushings - Part Number: 6705 Customer: kevin c appel Rating: 5 out of 5Overall Opinion: I replaced the factory bushings on my 68 GT500 Shelby with these parts. The steering is more responsive and they last. |
| Power Steering Bushings - Part Number: 6705 Customer: Joseph Bauer IV Rating: 5 out of 5Overall Opinion: Great I used these power steering bushings on a 50 year old car and they worked perfectly for my application. |
 | Front Leaf Spring Frame Shackle Bushings - Part Number: 6801 Customer: Brandon Bradbury Rating: 5 out of 5Overall Opinion: great! These bushings fit my 1974 F250 4x4 front frame shackles perfectly. |
 | Front Frame Shackle Bushings - Part Number: 6802 Customer: Michael R. Aigner Rating: 5 out of 5Overall Opinion: The parts I ordered worked great and the company did what they said they would. So I will use energy suspension in the future. |
 | Rear Frame Shackle Bushings - Part Number: 6807 Customer: Bradley Kalblinger Rating: 5 out of 5Overall Opinion: Great I have not installed these parts on my vehicle yet, however I have completed a test fitting of the bushings and they fit very well. the urethane bushings are well know for their long life and their stability, so their reputation precedes them I am not at all hesitant about how well they are going to work. |
 | Rear Frame Shackle Bushings - Part Number: 6810 Customer: Barry Prindle Rating: 5 out of 5Overall Opinion: Great Parts installed easily and are working great with no noise and vibrations |
 | Rear Leaf Spring Bushings - 1500 - 2000 LB Spring Rating - 1-1/2 Inch - Part Number: 71001 Customer: gregory miscamble Rating: 5 out of 5Overall Opinion: Bummer! Unfortunately, the parts did not fit my vehicle, so the exercise was a complete waste of time and money. Service, delivery, etc, was okay. |
| Rear Leaf Spring Bushings - 1500 - 2000 LB Spring Rating - 1-1/2 Inch - Part Number: 71001 Customer: robert dale Rating: 5 out of 5Overall Opinion: good product I ordered these bushings for the leaf spring and shackle mounts on my 1967 Chevy C10 pickup and they are too large for my truck. Good product, but they wont work for me. I had to send my springs out to be rebushed and had to settle for rubber when what I wanted was urethane. I'm disappointed that I cant find bushings to fit my truck. |
| Rear Leaf Spring Bushings - 1500 - 2000 LB Spring Rating - 1-1/2 Inch - Part Number: 71001 Customer: Jason Thompson Rating: 5 out of 5Overall Opinion: Worked |
 | Rear Leaf Spring Bushings - 1-1/2 Inch - 2600-3500 Spring Rating - Part Number: 71003 Customer: Garrett Asbury Rating: 5 out of 5Overall Opinion: Great Product Install was quick and easy once the old bushings were pressed out. So far they have performed as well as everyone claims they do, very satisfied... |
 | Replacement for Superlift #315 - Part Number: 71009 Customer: Cary Avey Rating: 5 out of 5Overall Opinion: fine Parts were great except for the fact that the dealer sent the wrong one so they never got installed on vehicle. |
| Replacement for Superlift #315 - Part Number: 71009 Customer: mark senesac Rating: 5 out of 5Overall Opinion: very good worked great thanks |
 | Body Mount Bushings and Radiator Support Bushings - Standard Cab - Part Number: 7101 Customer: DJ Bleggi Rating: 5 out of 5Overall Opinion: Very good quality!! Very happy with this product and fit just perfect to replace the old stock parts.. Thank you so much!! |
| Body Mount Bushings and Radiator Support Bushings - Standard Cab - Part Number: 7101 Customer: Sharon West Rating: 5 out of 5Overall Opinion: very good Got parts on time. If I need anything else I will us you, and will recommend to everybody else thanks |
| Body Mount Bushings and Radiator Support Bushings - Standard Cab - Part Number: 7101 Customer: larry rohrbach Rating: 5 out of 5Overall Opinion: excellent Perfect fit |
| Body Mount Bushings and Radiator Support Bushings - Standard Cab - Part Number: 7101 Customer: george mitts Rating: 5 out of 5Overall Opinion: Good looking parts, overall highly pleased Part was perfect and fit perfect. I had a problem with a part Graham took the same part off the shelf and to check the part I was having problem with and informed me it fit real tight. All the other parts I have bought from other dealers fit loose. These parts fit tighter for a lot longer life. I will buy parts from this dealer again. Don't be afraid to call them they will walk you through any problem you have. |
 | Rear Leaf Spring Eye and Shackle Bushings Kit - Mono Leaf - Part Number: 71010 Customer: Joe Fierro Rating: 5 out of 5Overall Opinion: Great! I was surprised how the car handled after changing the rear bushings. The car sits much better and doesn't have that sag look to it any more. |
| Rear Leaf Spring Eye and Shackle Bushings Kit - Mono Leaf - Part Number: 71010 Customer: Terry Wanner Rating: 5 out of 5Overall Opinion: easy install Complete kit is all I needed to replace worn factory original bushings. Easy install and great ride results. |
 | Rear Spring Eye and Shackle Bushing Kit - Multi Leaf - Part Number: 71012 Customer: Dale Gerred Rating: 5 out of 5Overall Opinion: Very good, works as designed Very easy install, of course over 40 yrs running my own auto repair shop may of had something to do with that. My only helpful thoughts about this kit is that you need at least 1 more packet of your super grease in the kit. |
| Rear Spring Eye and Shackle Bushing Kit - Multi Leaf - Part Number: 71012 Customer: Paul Cunningham Rating: 5 out of 5Overall Opinion: The top rear shackle bushes and bolt were a bit hard to install in the confide space when it was time to install them in the car . |
 | Rear Leaf Spring Bushings - 1.5 Inch Spring Eyes - Part Number: 71016 Customer: rodney fisher Rating: 5 out of 5Overall Opinion: they fit The rear spring bushings fit perfectly. I haven't got to the front yet but I'm sure they will be fine. |
 | Rear Leaf Spring Bushings - 1-3/8 OD Frame Shackle Bushings - Part Number: 71017 Customer: Eric C Anglea Rating: 5 out of 5Overall Opinion: Outstanding product!!! The only regret I have about buying these bushings is that I didn't buy the complete kit to do the whole truck! Its hard to imagine why the engineers at GM would ever believe the soft,py, rubber bushings they use in their cars and trucks would be sufficient. By the time my 20 year old truck is fully restored, Prothane bushings will replace all their factory rubber counterparts! |
 | Rear Leaf Spring and Shackle Bushings - Mono Leaf - Part Number: 71018 Customer: kevin blagdon Rating: 5 out of 5Overall Opinion: fit great everything fit great only complaint was not enough grease in the kit. made a big difference in handling |
 | Corvette Rear Spring Cushion- 1984-96 - Part Number: 71020 Customer: Paul Stuleber Rating: 3 out of 5Overall Opinion: Acceptable The Bushings are great, however, the washers are sub par as compared with the OEM washers. Specifically, the inside diameter of the washers allows more slop and they are not bonded to the bushing as was the original equipment was. |
| Corvette Rear Spring Cushion- 1984-96 - Part Number: 71020 Customer: kenny gingras Rating: 5 out of 5Overall Opinion: The best you can get for the great price |
 | Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 71022 Customer: Billy Spivey Rating: 5 out of 5Overall Opinion: Fit nicely At long last, I have been able to get around to replacing my rear springs and use these parts listed below that I purchased from you. I could not find a place on these web sites to leave any kind of a comment. Let me just tell you that these spring bushings are a very well made item. To my thinking they are very likely to prevent and not have squeaks that usually come. We did find that we had to use a razor blade to trim them down a bit both to get them to fit into the "eye" of each spring end and then slice off just a little bit from the larger ends that stick out in order to get them to go into the spring shackles and hanger. It was an easy thing to do. With this trimming they fit nicely and they are very likely to last the life of the car. B. Spivey |
| Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 71022 Customer: Patrick Van Dusen Rating: 5 out of 5Overall Opinion: GREAT PRODUCT WOULD PURCHASE AGAIN EASY TO INSTALL PERFECT FIT HAVEN'T HAD A CHANCE TO TRY THEM OUT YET (ON DRAGSTRIP) |
 | Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 71023 Customer: mark wilson Rating: 5 out of 5Overall Opinion: good seems to be a good product haven't finished the car yet. |
| Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 71023 Customer: Roy Knight Rating: 5 out of 5Overall Opinion: Very good product Easy to understand instructions and nice product. |
| Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 71023 Customer: David Ely Rating: 5 out of 5Overall Opinion: very happy Thanks for the email. I put these in this afternoon and everything went in spot on. The only problems I encountered was the fuel neck on the tank had to be loosened to remove the shackle for complete cleaning but that's not your problem. Over all, I am very happy with the product and instructions supplied. Thank you David Ely Perth Western Australia |
| Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 71023 Customer: Carroll Asbell Rating: 5 out of 5Overall Opinion: Great kit bushings fit nice, I would use these again. |
 | Rear Heavy Duty Shackle Kit - Multi Leaf - Part Number: 71051 Customer: Philip J. Clark Rating: 5 out of 5Overall Opinion: Excellent quality Installed perfectly! |
 | Front Sway Bar Bushings - 1-1/16 Inch - Part Number: 71101 Customer: Robert Chaparro Rating: 5 out of 5Overall Opinion: Completely satisfied with bushings. I bought these sway bar bushing for my 1981 Chevy truck. After installing, I can definitely feel the difference in the handling of my truck. I am completely satisfied with how these inexpensive bushings perform. I definitely will recommend them to my friends. |
| Front Sway Bar Bushings - 1-1/16 Inch - Part Number: 71101 Customer: Philip Holgado Rating: 5 out of 5Overall Opinion: Good OEM replacement Good value, and perfect fit. |
| Front Sway Bar Bushings - 1-1/16 Inch - Part Number: 71101 Customer: William J Holland Rating: 5 out of 5Overall Opinion: fit well they fit very well, the only down fall is the ones that go on the control arms, the slit at the bottom lets the sway bar rub on the control arm, metal to metal. It would be better if the slit was in the side, as the factory ones are...besides that, nice product and good price... |
| Front Sway Bar Bushings - 1-1/16 Inch - Part Number: 71101 Customer: John Judkins Jr Rating: 5 out of 5Overall Opinion: Easy installation, complete kit, fast shipping. Thanks |
| Front Sway Bar Bushings - 1-1/16 Inch - Part Number: 71101 Customer: Kenneth Harrison Rating: 5 out of 5Overall Opinion: They worked great and easy to install |
 | Front Sway Bar Bushings and Endlinks - 1-1/16 Inch - Part Number: 71104 Customer: GLADYS DE JESUS Rating: 5 out of 5Overall Opinion: Low price,great quality. Very satisfied with price and the quality. |
 | Front Sway Bar Bushings - 1-1/4 Inch - Part Number: 71107 Customer: Raymond Pomeroy Rating: 5 out of 5Overall Opinion: Excellent product, great value Very pleased with this purchase. Replaced completely shot bushings and what a difference. Easy installation and almost completely eliminated body roll. Cant beat the price either. Highly recommend. |
 | Front Sway Bar Bushings and Endlinks - 1-1/4 Inch - Part Number: 71110 Customer: Charles C Coffman Rating: 5 out of 5Overall Opinion: excellent Easy install...best price..very pleased. Thank you. |
| Front Sway Bar Bushings and Endlinks - 1-1/4 Inch - Part Number: 71110 Customer: Peter D Christensen Rating: 5 out of 5Overall Opinion: Well made easy to assemble good illustrations /instructions ! Would buy from these people again. Great service, shipped quickly, realistic pricing, and great quality parts. |
| Front Sway Bar Bushings and Endlinks - 1-1/4 Inch - Part Number: 71110 Customer: James Rating: 5 out of 5Overall Opinion: Great product Easy Install, exact fit, and great performance improvement. |
 | Front Sway Bar Bushings and Endlinks - 1-1/4 Inch - Part Number: 71111 Customer: jacob gibbs Rating: 5 out of 5Overall Opinion: Yes, I would recommend to a friend. The sway bar bushings seem to be a real high quality product, and should give years of good service. |
 | Front Sway Bar Bushings and Endlinks - 1-3/16 Inch - Part Number: 71114 Customer: Dan G Rating: 5 out of 5Overall Opinion: Works great!!!! The sway in my 99 Tahoe was bad, until i received the Prothane sway bar bushing link set and now the truck feels great! Thanks, |
 | Rear Sway Bar and End Link Bushings - 9/16 Inch -2 Bolt Clamp Style - Part Number: 71116 Customer: Ovidiu Cristea Rating: 4 out of 5Overall Opinion: good bushings, bracket holes were small Everything shipped packed nicely and even came with a small tube of grease for the bushings. The endlink bushings fit perfectly. The sway bar bushings would not fit in the stock brackets (different design) and the brackets provided in the kit had the holes a bit too small for the bolts that they need to be tightened with. A bit of work with a drill fixed the issue. |
 | Rear Sway Bar and End Link Bushings - 11/16 Inch - 2 Bolt Clamp Style - Part Number: 71118 Customer: Jerry Bahr Rating: 5 out of 5Overall Opinion: Great product Had a little problem sliding the longer bushings over the curves of sway bar. After several different tries was able to get them on using wd40 and vice. Maybe some instructions would help other customers. great product quality workmanship very happy with purchase. Thanks |
 | Body to Frame Mount Bushings - Standard Cab - Part Number: 7112 Customer: thomas bouts Rating: 5 out of 5Overall Opinion: Great parts fast shipping Parts are excellent quality, superior to factory in my opinion. Easy to follow directions and super fast shipping. Will use on all my future projects. |
| Body to Frame Mount Bushings - Standard Cab - Part Number: 7112 Customer: Brian Ruzicka Rating: 5 out of 5Overall Opinion: Work well they fit good and work well. No complaints |
 | Front Sway Bar Bushings - 34mm - Part Number: 71135 Customer: Lyle Hughes Rating: 5 out of 5Overall Opinion: Great I found this to be better than the original. It was supplied as ordered and included lubricant, which I was not expecting. Extremely pleased with product and service. |
 | Front Sway Bar Bushings - 32mm - Part Number: 71137 Customer: Eileen Joyce Rating: 5 out of 5Overall Opinion: Wonderful These fit my WS6 sway bar awesome and helped stiffen the suspension like I wanted. This company has fast shipping. |
 | Front Sway Bar Bushings and Endlinks - 33mm - Part Number: 71138 Customer: Jeffery A Patterson Rating: 5 out of 5Overall Opinion: Very nice parts Parts were shipped very quick and fit like a dream. They look good on the vehicle and preform even better. I would recommend these parts to anybody. Would order from this company again. Thanks for a great product. |
| Front Sway Bar Bushings and Endlinks - 33mm - Part Number: 71138 Customer: Kevin White Rating: 5 out of 5Overall Opinion: Works Great. I used this kit to replace my worn factory bushings and end links. This kit was easy to install, and is a definate improvement over stock. I liked the fact that this kit came with locking nuts, when the factory ones were not. |
 | Rear Sway Bar and Endlink Bushings - 23mm - Part Number: 71139 Customer: Henry L Williamson Rating: 5 out of 5Overall Opinion: Excellent Great replacement bushings....a lot better over OEM. |
| Rear Sway Bar and Endlink Bushings - 23mm - Part Number: 71139 Customer: Christian Kuehne Rating: 5 out of 5Overall Opinion: Very good parts with a nice price The parts are easy to install and they make a better control of the car. The shipping was very fast and cheap to overseas addresses. I would buy them again. |
 | Rear Sway Bar and Endlink Bushings -22mm - Part Number: 71140 Customer: jessica adams Rating: 5 out of 5Overall Opinion: great product easy to install huge difference in performance Installed in about 30 min. Excellent performance enhancement. |
 | Rear Sway Bar and End Link Bushings - 19mm - Part Number: 71142 Customer: Paul Stuleber Rating: 1 out of 5Overall Opinion: Poor Fit 1. The main sway bar bushing inside diameter was approximately 0.10" to small. When clamped the bushing would not wrap around the sway bar completely. Reused original bushings. 2. Sway Bar End Link Bushings did not include installation instructions and their tech department couldn't answer if metal casings should be reused. Answer is, NO. There isn't any way to possibly press the bushing into the original metal casing. Remove the casing and press bushing into bracket. Note however, that eliminating the metal casing increased the stress on the bushing as the surface contact is significantly reduced. Also,,, why design the bushing to have a groove the same width as the casing length? It should match the thickness of the bracket so the bushing cant move side to side. I installed AC Delco Bonded Rubber Bushings made same as OEM parts. Note, use loctite if you go this route and use a punch and form little "dents" around the casing to create interface so the casing stays put. Good luck! |
 | Rear Sway Bar and End Link Bushings - 24mm - Part Number: 71144 Customer: Noel Raufaste Rating: 5 out of 5Overall Opinion: Significant ride improvement. The car feels like it is brand new. It holds the road better, the vibrations and rattles are reduced. It's hard to believe this is a c4 vette over fifteen years old now. Big improvement, well worth the cash. Just make sure you thoroughly remove the old bushing rubber and clean the pieces. Then make sure you sufficiently lube the new poly bushings. |
 | Front Sway Bar and End Link Bushings - 24mm - Part Number: 71147 Customer: Buylow Computer Rating: 3 out of 5Overall Opinion: Parts took almost 3 weeks to arrive Product was just as ordered but took almost 3 weeks because I asked for red. |
 | Front Sway Bar and End Link Bushings - 30mm - Part Number: 71149 Customer: baumeister patrick Rating: 5 out of 5Overall Opinion: No problem for installation. Good material. A+++++ |
 | Body to Frame Mount Bushings and Radiator Support Bushings Kit - Part Number: 7115 Customer: S. Labonte c/o G Switzer Rating: 5 out of 5Overall Opinion: good we are doing a complete body and frame rebuild.Did a trial fit and the mounts will work perfect.we will not be installing them permanently till spring.Thanks |
 | Front Sway Bar Bushings - 24mm - Part Number: 71159 Customer: nathaniel dow Rating: 5 out of 5Overall Opinion: Great Price and quality. Prothane bushings are great my car handles better than ever. Great product. |
 | Front Sway Bar Bushings and Endlinks - 1-1/8 Inch - Part Number: 71167 Customer: Joseph Mercado Jr Rating: 5 out of 5Overall Opinion: Dissatisfied The diameter for the sway bar hole is perfect but there is a small gap about 1/8" between the flat side of the bushing and the frame. This causes movement and performance issues. |
 | Front Sway Bar Bushings and Endlinks - 1.42 Inch - Part Number: 71168 Customer: Terje Sollid Rating: 5 out of 5Overall Opinion: It was good quality parts The parts were very good, and very easy to install!! The old parts were hard to remove, because of rusted bolts. All in all, I'm very happy!! |
| Front Sway Bar Bushings and Endlinks - 1.42 Inch - Part Number: 71168 Customer: Eduards Terehovs Rating: 5 out of 5Overall Opinion: Great product All established without problems. Thanks, good details. |
 | Front Sway Bar Bushings and Endlinks - 1.25 Inch - Part Number: 71169 Customer: James Popp Rating: 5 out of 5Overall Opinion: Exellent!!! As a long time customer, using Energy Suspension parts in just about all of my regular vehicles and in every race car I've ever built, I was expecting superior quality when I purchased part #71169 sway bar bushing and end link kit to replace the worn ones in my 02 Suburban which does double duty as my daily driver and tow vehicle. As usual I was not let down. The performance difference was immediately noticeable and I know will remain that way for a long time.My only gripe(if a normal person would call it that) was that I didn't get any stickers!!! :) Thank you for providing a superior product that guys like me can count on not to let us down!!!! |
 | Body to Frame Mount Bushings and Radiator Support Bushings - Blazer - Part Number: 7117 Customer: James Gregory Rating: 5 out of 5Overall Opinion: Great upgrade to old worn out bushings Great part upgrade to old worn out mushy stock body bushings. |
 | Rear Sway Bar and Endlink Bushings - 23mm - Part Number: 71175 Customer: Gary McDaniel Rating: 5 out of 5Overall Opinion: Perfect In Every Way First off, these parts are of excellent quality. Fit and finish excellent! Price was right, fast shipping, and reasonable price on the shipping also. Thank you much! Gary Mc, Idaho |
| Rear Sway Bar and Endlink Bushings - 23mm - Part Number: 71175 Customer: Kevin White Rating: 5 out of 5Overall Opinion: Works Great. I used this kit to replace my worn factory bushings and end links. This kit is a definate improvement over stock. The hardest part of the installation is knocking the old rubber inserts out of the end links, so that you can install the new ones provided in the kit. |
| Rear Sway Bar and Endlink Bushings - 23mm - Part Number: 71175 Customer: Jean-Francois Bruneau Rating: 5 out of 5Overall Opinion: Nice stuff Fast installation thanks |
| Rear Sway Bar and Endlink Bushings - 23mm - Part Number: 71175 Customer: Tyler Moore Rating: 5 out of 5Overall Opinion: GREAT This Rear Sway Bar and Endlink Bushings - 23mm Part Number: 71175 kit was better than the factory set. They were super easy to install, and I like that the bushings are a two piece design instead of the factory one piece design |
| Rear Sway Bar and Endlink Bushings - 23mm - Part Number: 71175 Customer: Thomas Zultko Rating: 5 out of 5Overall Opinion: Outstanding Nothing but the best from customer service to the parts. I had emails of where my parts were from order confirmation when they were picked and when they where shipped. The bushings fit perfect and made a nice handling improvement on my Blazer. Thank You Tom Z. |
| Rear Sway Bar and Endlink Bushings - 23mm - Part Number: 71175 Customer: Marcel Marchand Rating: 3 out of 5Overall Opinion: I found that the original bushings were 14 years old but in my opinion were still better than the new Prothane set I received. I found the Prothane set to be very light duty and should be bulked up to ensure durability and endurance. |
| Rear Sway Bar and Endlink Bushings - 23mm - Part Number: 71175 Customer: tony webster Rating: 5 out of 5Overall Opinion: A great product As all the other Energy products, this item was easy to install and really made a difference in the actual feel of my truck. Thanks.....Tony |
| Rear Sway Bar and Endlink Bushings - 23mm - Part Number: 71175 Customer: NENA GRAGG Rating: 5 out of 5Overall Opinion: Great Product! This bushing set was a breeze to install. Looks so much better than the stock bushings, and definitely improved the handling of my Blazer! Highly Recommend this set! |
| Rear Sway Bar and Endlink Bushings - 23mm - Part Number: 71175 Customer: James w Sugg Rating: 5 out of 5Overall Opinion: I am pleased with the product. I am most pleased with energy suspension parts and expedited service! A well employed online and offline service/business model in support of quality parts. Thumbs up! |
 | Rear Sway Bar Bushings - 27mm - Part Number: 71179 Customer: Eric Moran Rating: 5 out of 5Overall Opinion: Firm and tight ride quality. Impressed with ride firmness and easy install. Chose the red version for looks, waited a week longer but looks great and worth it. Recommended! |
 | Body to Frame Mount Bushings Kit - Part Number: 7118 Customer: Brian Ponder Rating: 5 out of 5Overall Opinion: Too generic I had to modify the bolts, they were too long. I thought this would work better than it did. A little disapointed really, sorry. Brian Ponder |
 | Rear Sway Bar Bushings - 24mm - Part Number: 71185 Customer: jose corez Rating: 5 out of 5Overall Opinion: Very Happy Happy with the parts great shopping speed. |
| Rear Sway Bar Bushings - 24mm - Part Number: 71185 Customer: Kevin A Cristobal Rating: 5 out of 5Overall Opinion: better than oem. Great product right here! This is better than any other bushings you will find and the fitment was perfect. |
 | Front Sway Bar Bushings - 34mm - Part Number: 71187 Customer: Kevin A Cristobal Rating: 5 out of 5Overall Opinion: best bushings! Great product right here! This is better than any other bushings you will find and the fitment was perfect. |
 | Front Sway Bar Bushings - 30mm - Part Number: 71188 Customer: Eric Moran Rating: 5 out of 5Overall Opinion: Excellent so far! Impressed with ride firmness and easy install. Chose the red version for looks, waited a week longer but looks great and worth it. Recommended! |
| Front Sway Bar Bushings - 30mm - Part Number: 71188 Customer: ken Linderborg Rating: 5 out of 5Overall Opinion: good Good fit and finish. |
 | Rear Sway Bar Bushing Kit - 23mm - Part Number: 71189 Customer: ken Linderborg Rating: 5 out of 5Overall Opinion: Good Good fit and finish. |
 | Body Mount Bushings and Radiator Support Bushings - Hardtop Only - Part Number: 7119 Customer: juan rivera Rating: 5 out of 5Overall Opinion: Great item Not my first energy product. I have used many times before and have never been disappointed. Keep up the great work .....John |
 | Front Sway Bar Bushings - 24mm - Part Number: 71190 Customer: Jason Gaspar Rating: 5 out of 5Overall Opinion: very satisfied. The new sway bar bushings are a great addition from the stock. No more loud noises when going over bumps. Nice and quiet. Would highly recommend these ENERGY bushings. |
| Front Sway Bar Bushings - 24mm - Part Number: 71190 Customer: PETE TAMARIT Rating: 5 out of 5Overall Opinion: Better than factory, Thanks, I will highly recommend these parts. Great fit 2008 HHR LT 2.2 Auto. Easy to install, it took me about 30 minutes and I am very happy I found you guys. All rattling underneath is gone thanks again. Regards, Pete Tamarit. |
| Front Sway Bar Bushings - 24mm - Part Number: 71190 Customer: Benoit Proulx Rating: 5 out of 5Overall Opinion: Excellent It fit perfectly on my cobalt ss without any issue |
 | Body Mount Bushings - Convertible Only - Part Number: 7120 Customer: Chris M Bettinger Rating: 5 out of 5Overall Opinion: works Great! Great product and installed fairly easy. Followed directions and end result is what I wanted. Firmer and better than original. Vast improvement over OEM products made 43 years ago. I will add that convertible and standard items are different. If the vendors product doesn't state - For Convertible, it won't fit. Be sure to get the right part for the right application the first time. You'll be glad you did. I would recommend and buy this item again. |
| Body Mount Bushings - Convertible Only - Part Number: 7120 Customer: Timothy L. Steele Rating: 5 out of 5Overall Opinion: top quality the bushing fit well 15 year ago when i first built this car no one in the after market believed me that there was a difference between a convertible and hard top thank you for making a high quality product you should include torque specs with the kit thank you TL Steele |
 | Rear Strut Rod Bushings - Part Number: 71202 Customer: Yelton Enterprises Rating: 5 out of 5Overall Opinion: Looks good to me. Send me some more information everything looks GREAT. Send me some coupons and discounts |
 | Rear Strut Rod Bushings - Part Number: 71203 Customer: Milivoj Bracanovic Rating: 5 out of 5Overall Opinion: Worked very well. Everything went smooth with parts installation. Easier than I expected. I recommend it. |
| Rear Strut Rod Bushings - Part Number: 71203 Customer: Michael Raby Rating: 5 out of 5Overall Opinion: great Perfect fit |
| Rear Strut Rod Bushings - Part Number: 71203 Customer: Bruce Kane Rating: 5 out of 5Overall Opinion: Very, very good I got the parts, they were perfect, fit like a glove, and had everything I needed to get the job done. I will buy from them again, the price was the lowest I found, the parts were perfect, and the shipping got here so fast you'd think they were next door! Thank you, you got the clunking to stop! |
 | Rear Strut Rod Bushings - Strut Eye Same Size Each End - Part Number: 71204 Customer: Paul Stuleber Rating: 1 out of 5Overall Opinion: Poor These parts are not Engineered as well as the original equipment. 1. The inside diameter of the sleeves that connect to the differential do not have a provision to make contact with the bolt as does the original bushings. The original bushings have knobs pressed inward to allow the bolt to contact the inside of the sleeve. Only the washers that are reused support the bolt. The replacement design is weaker in comparison. 2. The sleeves and bushings were to wide when assembled onto the strut rod to be inserted into the spindle. I had to use a belt sander and remove just under 1/8" so that it could be installed. |
| Rear Strut Rod Bushings - Strut Eye Same Size Each End - Part Number: 71204 Customer: Robert Purcell Rating: 5 out of 5Overall Opinion: Good These parts were easy to install except the left side outer bush was tight in the hub carrier but eventually went in with the aid of a tapered drift pin.Has made a big difference to cars handling. Car has stopped tramlining and wondering under power, a big improvement for a small outlay. Would recommend these parts to any c4 corvette owner...Thanks |
 | Rear Strut Rod Bushings - Strut Eye Diff. Size Each End Re-Use All Metal Parts - Part Number: 71205 Customer: Rich Reuschling Rating: 5 out of 5Overall Opinion: Very nice, easy to install. Items packaged well, but directions would be nice too. The hard thing to do is remove the old bushings, need to be very careful not to damage the opening of the strut rods. New ones go in without any problems. Will certainly use this product again when updating my next C4 Vette. |
 | Front Strut Arm Bushing Kit - Part Number: 71206 Customer: david hill Rating: 5 out of 5Overall Opinion: they are on the car and customer is happy They seem fine, on the car and working |
 | Rear Track Bar Bushings - Part Number: 71207 Customer: Greg McConiga Rating: 5 out of 5Overall Opinion: Excellent Easy to do business with, fast delivery, great pricing and a quality product. What's not to love? |
 | Rear Track Bar Bushings - Panhard - Part Number: 71209 Customer: William Hunter Rating: 5 out of 5Overall Opinion: 100 All my suspension is prothane from pan hard bar to core support. I am not complete with my build but very happy thanks william |
| Rear Track Bar Bushings - Panhard - Part Number: 71209 Customer: Neil Zammit Rating: 5 out of 5Overall Opinion: excellent Installation was no problem, all good |
 | Rear Track Arm Bushing Kit - Panhard Bar - Part Number: 71210 Customer: Diego Granig Rating: 5 out of 5Overall Opinion: The parts are very good! Thanks for your help! Best greets from Austria! |
| Rear Track Arm Bushing Kit - Panhard Bar - Part Number: 71210 Customer: dirk grebe Rating: 5 out of 5Overall Opinion: perfect :-) fits perfectly on the panhard bar of my 1965 buick riviera :-) |
| Rear Track Arm Bushing Kit - Panhard Bar - Part Number: 71210 Customer: Robert Decker Rating: 5 out of 5Overall Opinion: very good Installed easily and worked great. |
 | Front Strut Rod Bushings - Part Number: 71211 Customer: Reo Haynes Rating: 5 out of 5Overall Opinion: Very impressed This product is of very good quality. The addition of this bushing kit restored the handling and ride of my 1965 Impala. You will not find a better kit for your car anywhere! Thank you Reo Haynes. |
 | Front Strut Rod Bushings - Part Number: 71212 Customer: c/o orlando J. Gonzalez Rating: 5 out of 5Overall Opinion: Good product Perfect fit. |
 | Body Mount Bushings and Radiator Support Bushings - Convertible Only - Part Number: 7122 Customer: tom rice Rating: 3 out of 5Overall Opinion: nice? The bushings look nice. My paint man noticed when he opened the package that they did not come with bolts. So I emailed energy suspension and they said you had to reuse your old hardware. Really? from a fifty year old car? Only half of mine came out in without a cutting torch. So now I need to buy new bolts. They should note that when they sell these. I could have bought another kit, with bolts, for three dollars more. |
 | Body Mount Bushings and Radiator Support Bushings - El Camino Only - Part Number: 7125 Customer: Augie Anderson Rating: 5 out of 5Overall Opinion: Good looking parts. Worlds better than what I have on the truck! Easy install. Much better than what I had on the truck. Glad you listed on ebay! Thanks again! |
 | Body Mount Bushings and Radiator Support Bushings - Part Number: 7127 Customer: Denise Underwood Rating: 5 out of 5Overall Opinion: Great upgrade ! Great product. Easy to install with excellent instructions |
 | Body Mount Bushings - 2 and 4 Door Sedans - Part Number: 7129 Customer: Kirk Mang Rating: 5 out of 5Overall Opinion: like the product The product is superior to others that I have used on other projects. The fitment was excellent and the results were great. My friend assisted me in the installation and they went in easy and the instructions were easy to follow. My hats off to the manufacturer for an excellent product. Thanks Kirk |
| Body Mount Bushings - 2 and 4 Door Sedans - Part Number: 7129 Customer: dr Upton Rating: 5 out of 5Overall Opinion: perfect lifted the body fitted straight in a real nice ride now |
 | Body Mount Bushings - Convertible Only - Part Number: 7130 Customer: Bennie L. Morrow Rating: 5 out of 5Overall Opinion: haven't had a chance to install parts yet thanks |
| Body Mount Bushings - Convertible Only - Part Number: 7130 Customer: Kevin Poteet Rating: 5 out of 5Overall Opinion: good quality parts Very happy with purchase experience and quality of product. |
| Front Lower Control Arm Bump Stops - Part Number: 71302 Customer: christopher spratt Rating: 5 out of 5Overall Opinion: The lower bump stops were easy to install and are effective. | |
 | Body Mount Bushings - Part Number: 7132 Customer: Joseph P. Karetski Rating: 5 out of 5Overall Opinion: Great product, Great price, Reasonable shipping This product met my needs and more. Great Quality, perfect fit, no problems what-so-ever Thank you Joe |
| Body Mount Bushings - Part Number: 7132 Customer: Richard Morrill Rating: 3 out of 5Overall Opinion: good It should have come with directions because of the different sizes. It also should have come with bolts |
 | Body Mount Bushings - Part Number: 7133 Customer: Oddmund Nordhagen Rating: 5 out of 5Overall Opinion: Very satisfied |
 | Body Mount Bushings and Radiator Support Bushings - Hardtop Only - Part Number: 7139 Customer: Tyrone Savill Rating: 5 out of 5Overall Opinion: Not as great as it could have been Before I start. I have submitted my comment on this to your supplier. You do get everything needed for putting your Sub-frame and Radiator Core back to rights, but we have just fitted only the Radiator Core Bushings so far and we had to make the Holes bigger in the Sub-Frame so they would fit. Also the Diagram did not coincide with the Core and Frame illustration ! We had to use the Frame illustration as the Core and the Core illustration as the Frame ! I am hoping this will not be the case when we come to fitting the main Sub-Frame Bushings. So really these issues need addressing then this will be an excellent product. |
| Body Mount Bushings and Radiator Support Bushings - Hardtop Only - Part Number: 7139 Customer: John Guerrero Rating: 5 out of 5Overall Opinion: this kit fit perfectly.everthing was labeled & fit very well. I give this kit a 10. Thanks fellas. |
 | Body Mount Bushings and Radiator Support Bushings - Part Number: 7141 Customer: Joshua B. Smith Rating: 5 out of 5Overall Opinion: Great Product. These are without a doubt a must have to anyone. I bought a set for my 04 Silverado because the factory rubber mounts were just destroyed. Installed these in about an hour or so now my truck sits up level again and it regained the ride back that it had when it was new. |
| Body Mount Bushings and Radiator Support Bushings - Part Number: 7141 Customer: Jeremy Beaver Rating: 5 out of 5Overall Opinion: Bushings seem to be made really well and will probably last for a longer time than stock, however it did give the truck a rougher ride due to the hardness of the mount |
| Body Mount Bushings and Radiator Support Bushings - Part Number: 7141 Customer: michael - shiptoski Rating: 5 out of 5Overall Opinion: fit my needs perfect matched bodylines back up,and strength too old ones,no comparrison excellent product |
 | Transfer Case Torque Mount Bushings - Part Number: 71603 Customer: Robert A Shaw Rating: 4 out of 5Overall Opinion: good The metal sleeve on the originals have a smaller inside diameter.I had to add rubber sleeves around the bolts to take up the difference,otherwise the transfer case would not fit properly.I realize that some aftermarket parts may not fit as the originals so overall I was happy to find something that would work. |
 | Transmission Mount Kit- 1 or 2 Bolt Style - Part Number: 71604 Customer: Gustavo Cantu Rating: 5 out of 5Overall Opinion: Excellent Direct bolt on! Highly recommended due to precise fit and no hassle replacement over flimsy stock rubber mount. Installed on the 4L60E trans-mount like it was always supposed to be there. |
| Transmission Mount Kit- 1 or 2 Bolt Style - Part Number: 71604 Customer: Cody Allen Rating: 5 out of 5Overall Opinion: Thumbs Up Exactly what I ordered, shipped immediately. Cannot Ask for more. |
| Transmission Mount Kit- 1 or 2 Bolt Style - Part Number: 71604 Customer: RODERICK CRAWFORD Rating: 5 out of 5Overall Opinion: It appears to be a very high quality part. I replaced the original trans mount that I had replaced new 40 years ago on my 1965 vette.The new part is superior to the original rubber mount.It was an exact replacement. |
| Transmission Mount Kit- 1 or 2 Bolt Style - Part Number: 71604 Customer: ryan martin Rating: 5 out of 5Overall Opinion: Good Good |
| Transmission Mount Kit- 1 or 2 Bolt Style - Part Number: 71604 Customer: Travis Pilewski Rating: 5 out of 5Overall Opinion: solid product, great price Solid product. Really firmed up any drivetrain slop. No more shakes from he stock rubber mount. Car feels completely different after swapping out transmission and motor mounts. |
| Transmission Mount Kit- 1 or 2 Bolt Style - Part Number: 71604 Customer: kenneth patnude Rating: 5 out of 5Overall Opinion: fit very well no mods reqd No problems at all, fit form and function perfect |
 | Rear Differential Carrier Bushings - Part Number: 71607 Customer: grupe LLC Rating: 5 out of 5Overall Opinion: good parts They worked well. I used them in a custom setup on my Miata and haven't had any issues. |
| Rear Differential Carrier Bushings - Part Number: 71607 Customer: Eric Eylat Rating: 5 out of 5Overall Opinion: Great kit The carrier bushings fits perfectly into the diff cover with a slight press fit. The installed width is correct and fits into the frame bracket without issue. Note that I was unable to remove the factory bushing with my small 12 ton Harbor Freight press at home. Using a 25 ton hydraulic press at work the original bushings shells "popped" loose at 18 tons. |
| Rear Differential Carrier Bushings - Part Number: 71607 Customer: Alexander Goodstein Rating: 5 out of 5Overall Opinion: Great! Shipped fast, fit great, didn't require a press to get in! |
| Rear Differential Carrier Bushings - Part Number: 71607 Customer: Salvatore Cracchiolo Rating: 5 out of 5Overall Opinion: Excellent Quality and expert manufactured parts Excellent Quality and expert manufactured parts and easy to install. Thank you for the excellent product. Sal C cracchiolo |
 | Torque Arm Bushing - Differential to Transmission - Part Number: 71609 Customer: osage walkup Rating: 5 out of 5Overall Opinion: Very close to stock with way better material Part went in like it was designed, really like the bolt in feature. Much better than just buying just a rubber mount and sticking it in there and praying it well stay. Thank you for a quality part, works excellent. |
| Torque Arm Bushing - Differential to Transmission - Part Number: 71609 Customer: Whatever! Customs Rating: 5 out of 5Overall Opinion: Thank you. Great seller! |
 | Rear Lower Spring Pads - Mono Leaf - Part Number: 71705 Customer: TERRY WILLIAMS Rating: 5 out of 5Overall Opinion: great Rear lower spring pads were a perfect fit, just like they came straight out of the factory. |
 | Rear Upper Coil Spring Isolators - Part Number: 71706 Customer: Tim Heathcoat Rating: 5 out of 5Overall Opinion: They work great but I wish they fit the springs a little tighter. I could not mark them down due to the fact that I was using aftermarket springs |
| Rear Upper Coil Spring Isolators - Part Number: 71706 Customer: Chris darknell Rating: 5 out of 5Overall Opinion: nice parts They fit well and took out the squeak I had. Thanks |
| Rear Upper Coil Spring Isolators - Part Number: 71706 Customer: Steve or Candace Atwood Rating: 5 out of 5Overall Opinion: Nice quality All good. Easy to install and fit great. |
| Rear Upper Coil Spring Isolators - Part Number: 71706 Customer: Cassy Fowler Rating: 5 out of 5Overall Opinion: Worked well. Good fit, much better than stock. Worked out well. |
| Rear Upper Coil Spring Isolators - Part Number: 71706 Customer: David A Ward Jr Rating: 2 out of 5Overall Opinion: Very Dissatisfied These Isolators are too small and the centers are not correctly shaped to fit the the Frame protrusion they are meant to be seated onto on my 1979 Chevy Malibu.Given the fact that there is an ever increasing market for parts to fit older vehicles one would think that much more attention to detail and fit would be given by this manufacturer.I did not send them back because after shipping expense and time it would have not been worth the hassle--just one of the drawbacks of ordering online. |
 | Rear Leaf Spring Pads - Mono Leaf - Part Number: 71707 Customer: Coleen K. Hanson Rating: 5 out of 5Overall Opinion: The parts fit good. Great service from your company. Thank you |
| Rear Leaf Spring Pads - Mono Leaf - Part Number: 71707 Customer: michael sigmon Rating: 5 out of 5Overall Opinion: worked great , Tight fit . Worked fine, Tight fit on pin. |
| Rear Leaf Spring Pads - Mono Leaf - Part Number: 71707 Customer: Earl Bingham Rating: 5 out of 5Overall Opinion: Good quality and fit These went on easily and fit correctly. And the price was right too! |
 | Rear Spring Pads - Multi Leaf - Part Number: 71708 Customer: Jerome Anderson Rating: 5 out of 5Overall Opinion: The pads are too thick over all. I think they are made of quality materials they just don't fit properly. The locator pin is also the wrong shape for the leafs and they are too thick. One other gripe there are at least 3 different leaf styles and only one friction pad set option. |
| Rear Spring Pads - Multi Leaf - Part Number: 71708 Customer: Pasi Liukka Rating: 5 out of 5Overall Opinion: Very good product. After installing these parts, all the slack was gone from the rear suspension. |
| Rear Spring Pads - Multi Leaf - Part Number: 71708 Customer: Cliff Plunkett Rating: 5 out of 5Overall Opinion: positive Great part, just installed but have not driven car yet. |
| Rear Spring Pads - Multi Leaf - Part Number: 71708 Customer: Douglas E. Charnley Rating: 4 out of 5Overall Opinion: My overall impression of these rear leaf spring pads are favorable. I replaced the pads in my 1968 Pontiac Firebird. They were easy to install but did not slip right in as they were too wide out of the box. I needed to remove material from the both edges of the two upper pads with a bench grinder before they would fit up into the existing spring perches. Not a big deal, but I didn't expect modification would be required. Once installed, I was pleased with the improvement in the ride. I would not hesitate to purchase these parts again. |
| Rear Spring Pads - Multi Leaf - Part Number: 71708 Customer: STEVEN BROWN Rating: 5 out of 5Overall Opinion: GOOD FIT QUALITY PRODUCT Good fiit, great price. |
 | Rear Leaf Spring Pads - Multi Leaf - Part Number: 71709 Customer: Dmitriy Lemeshko Rating: 5 out of 5Overall Opinion: Very good quality |
| Rear Leaf Spring Pads - Multi Leaf - Part Number: 71709 Customer: Paul Cunningham Rating: 5 out of 5Overall Opinion: These parts were quite asy to fit and seem to be performing well. |
| Rear Leaf Spring Pads - Multi Leaf - Part Number: 71709 Customer: GENE hudson Rating: 5 out of 5Overall Opinion: Hello, the parts fit and were just what I needed. 5 star and very good service god bless gene hudson toledo, ohio |
 | Coil Spring Isolator Rear Upper- 91-96 - Part Number: 71710 Customer: Andy Gordon Rating: 4 out of 5Overall Opinion: They fit, they work. Simple to install. Took less than 30 min per spring. Would be nice if they came with some sticky tape to hold in place while installing. |
 | Radiator Isolators - Small Block - Part Number: 71711 Customer: howard Rating: 5 out of 5Overall Opinion: very nice product had to trim some off of the end otherwise five star product Very nice product, had to trim some off of the end for otherwise five star product good deal too |
| Radiator Isolators - Small Block - Part Number: 71711 Customer: Troy R Helwig Rating: 5 out of 5Overall Opinion: Great Great mounts at a Great price, and very fast shipping!!! Thank You Troy |
| Radiator Isolators - Small Block - Part Number: 71711 Customer: Johns Racecraft Rating: 5 out of 5Overall Opinion: nice parts I still had to modify them to fit the radiator support. They fit the radiator just fine |
| Radiator Isolators - Small Block - Part Number: 71711 Customer: David Sweet Rating: 5 out of 5Overall Opinion: Thumbs up Great part, installed easy. Highly recommend. |
| Radiator Isolators - Small Block - Part Number: 71711 Customer: JR / Sylvia Hernandez Rating: 5 out of 5Overall Opinion: Very good material, most excellent.......... ordered wrong size but very good material. Thank u very much for being one of the vendors of EBay. Sincerely, JR |
| Radiator Isolators - Small Block - Part Number: 71711 Customer: Alex Major Rating: 5 out of 5Overall Opinion: Good The parts fit properly and are doing the job. Thanks, Alex Major |
| Radiator Isolators - Small Block - Part Number: 71711 Customer: gary musselman Rating: 5 out of 5Overall Opinion: They fit better than the stock ones |
| Radiator Isolators - Small Block - Part Number: 71711 Customer: Jim Yurkovich Rating: 5 out of 5Overall Opinion: great All is well. Worked great. |
 | Radiator Isolators - Big Block - Part Number: 71712 Customer: kenneth patnude Rating: 5 out of 5Overall Opinion: excellent Fit like a glove. Did what it was supposed to do. No mods required. |
| Radiator Isolators - Big Block - Part Number: 71712 Customer: Michael Heider Rating: 3 out of 5Overall Opinion: The dimple on the top of the isolator fit through the metal bracket exactly like it was supposed to, but was a little too small to beheld in place while the radiator was being put in place. |
| Radiator Isolators - Big Block - Part Number: 71712 Customer: Aram Kazazian Rating: 5 out of 5Overall Opinion: Excellent part, will buy again |
| Radiator Isolators - Big Block - Part Number: 71712 Customer: gary musselman Rating: 5 out of 5Overall Opinion: Fit like a charm |
| Radiator Isolators - Big Block - Part Number: 71712 Customer: John Self Rating: 5 out of 5Overall Opinion: Good Product, better than factory! I received the parts within four days of ordering them with standard mail. The parts were better than I expected. They are a good fit and are a great up-grade from stock. Buy these with confidence! |
| Radiator Isolators - Big Block - Part Number: 71712 Customer: adam gordon Rating: 5 out of 5Overall Opinion: good finish and fit Parts dropped straight into factory rails, and fit the original radiator well. |
| Radiator Isolators - Big Block - Part Number: 71712 Customer: Danita Reifke Rating: 5 out of 5Overall Opinion: I have not installed them yet They are fast to ship items. I have not installed them yet. |
| Radiator Isolators - Big Block - Part Number: 71712 Customer: jim tauscher Rating: 5 out of 5Overall Opinion: return everyone there has been very helpful, i just sent them back igot big block pads and i needed small block pads.Thanks for the e-mail and your interest. THANK YOU VERY MUCH Jim Tauscher |
| Radiator Isolators - Big Block - Part Number: 71712 Customer: Robert Del Santo Rating: 5 out of 5Overall Opinion: Parts look great, but I'm not sure that they are going to work on my application. I took a chance buying them. They appear too long for my application. I'm working on a 78 Chev p/u with 350. |
| Radiator Isolators - Big Block - Part Number: 71712 Customer: Andy Boone Rating: 5 out of 5Overall Opinion: excellent I used these on a custom alum. radiator. Worked great! Good price and fast shipping. |
 | Radiator Isolators - Small Block - Part Number: 71713 Customer: Michael Logue Rating: 5 out of 5Overall Opinion: Better than stock I bought these because I lost one of the original top rubber. After realizing the quality I removed the radiator again and replaced them all. |
 | Front Coil Spring Isolator Lift Spacer Kit - 2 Inch - Part Number: 71716 Customer: Cody Rating: 2 out of 5Overall Opinion: Needs improvement!!!! This kit is very attractive because of the price but I guess you get what you pay for. I received the kit quickly which was nice but there were not any instructions for installation. I contacted prothane customer support and they don't have any instructions, the guys told me that it seems pretty self explanatory. Well it does require cutting of the factory strut studs and there is not any kind of torque called out for the provided extension bolts. I snapped one clean off at the threads with a ratchet. What grade hardware does this include??? I was able to get everything installed eventually with some crafty additions and modifications. Disappointed but it does level the truck. |
 | Motor and Transmission Mount Kit - Part Number: 71906 Customer: David mark sullivan Rating: 5 out of 5Overall Opinion: These parts fitted a dream no more delay between power down and take up great bushes Easy to fit. Would recommend these bushes. |
 | Motor and Transmission Mount Kit - Part Number: 71910 Customer: Adam Tyrone Rating: 5 out of 5Overall Opinion: You guys make parts the right way! I have ordered motor mounts from o riellys and other car care places before. Lots of them. They come from china and half of them are for Oldsmobile cars! Not only are your mounts the MOST high quality that I have found. You also sell them matched with the tranny mount for my sm-465. If you know Chevy than you know how hard it is to find! You guys have a customer for life! |
 | Total Kit - Part Number: 72006 Customer: Oliver Kohl Rating: 5 out of 5Overall Opinion: Perfect Drivability I buy this kit for my 79 Pontiac Trans Am. The old bushings are worn out by the last 31 Years. The mount of this Kit is easy and it's all in the Kit what you (or the Car) needs. The First Mile after installation of the Kit was amazing, my Baby drives like a New Corvette or something else. The twisting between the Body and the chassis is complete away and it drives like a Cart, the feel from the Steering isn't perfect direct. Buy this kit. Energy suspension Parts is a perfect Seller with cheap Prices and super fast delivery |
 | Total Kit - Part Number: 72008 Customer: Keith Linden Rating: 5 out of 5Overall Opinion: great kit! includes everything!! I've ordered and installed other poly bushing kits for other cars in the past of other brands. This is the first time I've ordered a prothane kit. I have to say this is the only kit that I have not been looking for one or two more bushings to complete my suspension at the end of the day. They included bushings for all stock combinations of sway bar sizes, and torque arm designs, as well as some poly spacers for the rear control arms to help with side movement, that my car never originally had. Seems like a nice performance upgrade. I installed this kit as part of a complete suspension overhaul, as of now the car is entirely brand new at the stock level, aside from now having poly bushings. The car feels nice and tight, I have no clunks and so far no squeaks but I've only driven about 50 miles on the new bushings so far. If you're in the market for a complete poly kit for your car, look no further then the prothane kit. You won't be disappointed. |
 | Front Control Arm Bushings - Part Number: 7201 Customer: alejandro rosales Rating: 2 out of 5Overall Opinion: The package had a big bushing missing so I had to buy rubber replacement bushings for the bottom control arms and only used the polys on the top control arms. |
 | Total Kit - with Transmission Mount - Part Number: 72011 Customer: Raymond Fayo Rating: 5 out of 5Overall Opinion: Great product. Easy to install. Great ride and handling |
 | Total Kit - Part Number: 72013 Customer: Robert Davis Rating: 1 out of 5Overall Opinion: dont like Some of the bushings don't fit. A waste of my hard earn money. Won't buy from you again |
| Total Kit - Part Number: 72013 Customer: Jukka Salin Rating: 5 out of 5Overall Opinion: great The only thing I missed was the installation instructions |
 | Total Kit - Part Number: 72014 Customer: ken Linderborg Rating: 5 out of 5Overall Opinion: Good My old rubber bushings have metal sleeves bonded to the ID of them. It was a major P.I.T.A. to remove these from the old so that I could re-use them in the new ones. I would not buy this kit in the future without the option of also purchasing new sleeves. The new bushings themselves are high quality and I have no issues with them. |
 | Total Kit - 2 Door Hardtop Only - Part Number: 72015 Customer: Jan Muth Rating: 5 out of 5Overall Opinion: Perfect stuff |
 | Total Kit - Part Number: 72016 Customer: Mark Meyers Rating: 2 out of 5Overall Opinion: Less than impressed. The overall quality looks nice. However the upper and lower control arm bushings were not the correct size and I could not use the bushings for the leaf springs either. I have 2 extra set of sway bar bushings still in the package. I would love to find someone to buy all the items left over. I will not be purchasing any of these products again. |
 | Total Kit - Standard Cab - Part Number: 72020 Customer: Patrick Belanger Rating: 5 out of 5Overall Opinion: Great Every thing fit great. Just needed to makeshift some washers to hold them up, but other than that, great fit |
 | Front Control Arm Bushings - without Shells - Part Number: 7203 Customer: howard hill Rating: 5 out of 5Overall Opinion: worked for me fine product Everything was very user friendly. I even got quick shipping. The products seem to fit very well, I'm Happy. |
| Front Control Arm Bushings - without Shells - Part Number: 7203 Customer: Michael Aguiar Rating: 4 out of 5Overall Opinion: Awesome product Ive driven many S10s over the years. From bone stock to slammed & hot rodded but none ever felt as good as when i installed these poly bushings on my truck. From the performance aspect of it, no complains here. It exceeded my expectations. |
| Front Control Arm Bushings - without Shells - Part Number: 7203 Customer: dustin vandermooren Rating: 4 out of 5Overall Opinion: good product I had to shorten the inner bushing sleeves to work properly w/ my 87 s10 upper control arms. Otherwise, they seem great for the price. |
 | Total Kit - Part Number: 72032 Customer: Andrew Braunm Rating: 4 out of 5Overall Opinion: good They work very well, but what I did not like was that I had to buy 4 new stock bushings and burn out the center. I think they should come complete. |
 | Total Kit - Part Number: 72036 Customer: Gale Johnson Rating: 5 out of 5Overall Opinion: Love them The ride of my Tahoe completely changed. From what I described as a "couch on wheels" to an SUV that rides on rails. I love what the urethane bushings have done. Thanks for a great product. Could have used a little more grease in the package. Maybe I was too liberal with my application. LOL. |
 | Front Control Arm Bushings - Part Number: 7204 Customer: David J Backer Rating: 5 out of 5Overall Opinion: Excellent quality and material These parts greatly improve steering and suspension feel. The only issue I had with the installation was the instructions about installing the new steel sleeves in my control arms for the upper bushings. I did find that leaving the sleeves in the house freezer over night made a big difference as well as applying heat to the control arm surface. This did make for a very nice fit when all said and done. This was my first time installing control arm bushings in any vehicle and was able to do it in a few hours for both sides and I changed ball joints and tie rod ends as well in that same time so I can say that it was very easy to change the Prothane control arm bushings and would definitely recommend them to anyone. |
 | Total Kit - Part Number: 72042 Customer: Nicole Geary Rating: 5 out of 5Overall Opinion: These parts are great. Easy installation and very good quality. |
 | Front Control Arm Bushings - Part Number: 7205 Customer: James Rating: 5 out of 5Overall Opinion: Exactly what I expected, great improvement Bushing install was easy using a ball joint press tool - make sure to get extra lube if you do install yourself, made new bushings, inserts and even bolts slide in easy. I used a sazall to remove old bushings, burning seemed too messy, need to have good hand with sazall though. Job was quick, installed on 1996 C1500, truck turns on a dime now, air bags in back with traction bars and increased swaybar width with poly bushings helps too. Best upgrade choice/process to date! |
 | Front Control Arm Bushings - Part Number: 7206 Customer: Jason Chadwick Rating: 5 out of 5Overall Opinion: great product! After 198,256 miles my 95 Chevy truck still looked good but handled like a wet sponge. I rebuilt the front end and installed new polyeurethane bushings and was thoroughly satisfied. My truck feels tight again, no more wet sponge. I have used other products from energy suspension and will continue to use them in the future to keep my old skool rides on the road. thanks |
 | Front Control Arm Bushings - with Shells - Part Number: 7210 Customer: Brian Fishburn Rating: 5 out of 5Overall Opinion: very good product I found after cleaning control arm the where easy to fit |
 | Front Control Arm Bushings - With 1.625 Inch OD Front Lower - Part Number: 7212 Customer: mathieu menvielle Rating: 5 out of 5Overall Opinion: perfect parts in place , very good quality , better than original one. |
| Front Control Arm Bushings - With 1.625 Inch OD Front Lower - Part Number: 7212 Customer: Alex Pinon Rating: 5 out of 5Overall Opinion: Good Very well built bushings |
 | Front Control Arm Bushings - 1.65 Inch OD Lower - Part Number: 7217 Customer: Will Wallman Rating: 1 out of 5Overall Opinion: Poor fit of Prothane 7217 bushings It took 6 hours to install lower control arm bushings on a 67 Camaro using Prothane 7217 bushings. Prothane steps up the OD about .010 over stock for some reason and 3 professional mechanics one of which is a front end specialist could see no reason for the step up in OD. Make them the same diameter as OEM and they can be installed easily using a bench vise and a socket for backing. We resorted to a 30 ton press and only succeeded in starting to flex the metal control arm. Released the press and the Prothane bushing was still loose. Finally resorted to bench grinding the excess metal from the OD of the outer sheath before we achieved a tighter than OEM fit. Once the outer sheath was ground down to size all other parts assembled in less than 2 minutes. I won't be using these bushing for anything at any time in the future until Prothane addresses the problem or improves their instructions. Strongly suggest that someone at Prothane try to install kit 7217 in a lower control arm. Maybe then the design will change. |
| Front Control Arm Bushings - 1.65 Inch OD Lower - Part Number: 7217 Customer: Troy A. Harrison Rating: 5 out of 5Overall Opinion: worked GREAT these direct replacements worked GREAT - its not an easy job to put them in, but these fit great, no issues with installing in old, original parts.. |
 | Front Control Arm Bushings - with Oval Lower - with Shells - Part Number: 7222 Customer: Pat Ryan Rating: 5 out of 5Overall Opinion: great quality busshings Bushing are of very good quality and they fit perfectly. Car rides smother than most any new car now and handling is greatly improved. |
 | Rear Control Arm Bushings - with Shells - Part Number: 7225 Customer: Justin Arsenault Rating: 5 out of 5Overall Opinion: excellent fit, night and day difference in stiffening suspension!! Awesome kit. Great fit, fast shipping and priced very well for the quality!! |
 | Front Control Arm Bushings - Part Number: 7227 Customer: Enrique Figueroa Rating: 5 out of 5Overall Opinion: The installation was completed . The confusion was the internal steel sleeves and bushings that is a requirement for a complete installation. You should offer a complete set with sleeve and bushings for clients that may require this specially if its a complete restorative project like in my case. I did not have the original stock shells & bushing only the plates. |
 | Front Control Arm Bushings - with Shells - Part Number: 7231 Customer: Richard Franklin Rating: 5 out of 5Overall Opinion: Excelent These are great for S-10s with a v8 conversion. Nice smooth ride, no squeaks. |
| Front Control Arm Bushings - with Shells - Part Number: 7231 Customer: anthony grob Rating: 5 out of 5Overall Opinion: Great parts for the money. After installing these bushings my ride was firmed up immediately and it felt more stable driving in a straight line as well.86958 |
 | Front Control Arm Bushings - w/o Shells - Part Number: 7234 Customer: Chet Martel Rating: 5 out of 5Overall Opinion: So much better then rubber or the flimsy after market ones. Drives like it's on rails. Not bad for a baby cavilar , con feel every in pavement. NICE |
| Front Control Arm Bushings - w/o Shells - Part Number: 7234 Customer: donovan clark Rating: 2 out of 5Overall Opinion: great if thet all fit Kit was easy to install once we got the old bushings out. Two of the upper control arm bushings didn't fit. So my driver side still has the original rubber in the upper. Sucks but I was rebuilding the entire front end and that was the one part that didn't fit right. Stuff happens |
| Front Control Arm Bushings - w/o Shells - Part Number: 7234 Customer: Matt Rating: 5 out of 5Overall Opinion: Great lower control arm bushings Really stiffened up front suspension. Have had them in for 3 months now and still holding perfectly. Would recommend to everyone. Fixes vertical mount problem in all cavalier/ sunfire/ grand am rear mount problems. Will post again in a year for a follow up. Don't hesitate to buy. |
| Front Control Arm Bushings - w/o Shells - Part Number: 7234 Customer: Cory Van Santen Rating: 5 out of 5Overall Opinion: great product Noticed improvements right away with these. Great product |
| Front Control Arm Bushings - w/o Shells - Part Number: 7234 Customer: Roofy Rating: 4 out of 5Overall Opinion: Excellent fit. Great product. These bushings are a great replacement for the soft rubber OEM bushings. Aside from the 95-05 Cavalier and Sunfire, these also fit all 99+ Grand Am, Alero, 97-04 Malibu/Classic, and also all Chevy Cobalt, HHR, Pontiac G5 models. |
 | Front Control Arm Bushings - Part Number: 7237 Customer: Daniel Renteria Rating: 5 out of 5Overall Opinion: Ok. Steel bushings didn't fit, had to take them in to get drilled to the proper size. Besides that they seem to be holding up so far. |
 | Rear Control Arm Bushings - Part Number: 7301 Customer: Kendall Burleigh Rating: 5 out of 5Overall Opinion: Fits good fit was good. quality parts. I would recommend to anyone. |
 | Rear Track Bar Bushings - Part Number: 7302 Customer: Joseph Husler Rating: 5 out of 5Overall Opinion: great Old bushings had no metal sleeve other than the barrel on the end of the bar. Other than confusion over that they fit just right and work just right. The test of time will show how well they hold up. Confidence is high and the truck rides much better. Thanx |
| Rear Track Bar Bushings - Part Number: 7302 Customer: Carlton Haywood Rating: 5 out of 5Overall Opinion: Good product These bushings were easy to install and at a reasonable price. No special tools were needed. Very satisfied. |
 | Rear Control Arm Bushings - without Shells - Part Number: 7304 Customer: Adam M Jarvis Rating: 5 out of 5Overall Opinion: Impressed For about the same price as stock replacement bushings, I got these polyurethane bushings. Installation was just as easy or easier than the stock replacements. My bump steer (a common issue on my car) was significantly reduced. |
 | Rear Control Arm Bushings - Single Upper Arm - Part Number: 7307 Customer: Nick Barrera Rating: 5 out of 5Overall Opinion: Like the bushings A+++ Great bushings A++++ |
| Rear Control Arm Bushings - Single Upper Arm - Part Number: 7307 Customer: Barry Rowe Rating: 5 out of 5Overall Opinion: good Easy product to install. |
 | Rear Control Arm Bushings w/o Shells - Part Number: 7315 Customer: Delano Canales Rating: 5 out of 5Overall Opinion: Great product I love these they are always a perfect fit and never had any problem installing them. I can feel the difference in the way the car handles. If you want to get rid of the soft mushy ride, try these. |
| Rear Control Arm Bushings w/o Shells - Part Number: 7315 Customer: Belmarie Reyes Rating: 5 out of 5Overall Opinion: Excellente Easy to install.. excellent |
| Rear Control Arm Bushings w/o Shells - Part Number: 7315 Customer: Paul Stuleber Rating: 5 out of 5Overall Opinion: EXCELLENT These parts could be installed perfectly. |
| Rear Control Arm Bushings w/o Shells - Part Number: 7315 Customer: Gary G. Rating: 5 out of 5Overall Opinion: Very Good As in my Sway bar End link review these upper and lower Control arm bushings went in easily with my shop press. The packets of lube are Not enough to lubricate everything. I liberally coated everything in Marine Grease. My original low mileage factory bushings wereed and the control arms were binding. When I put the rear of the car on jack stands I was amazed to see very little droop of the rear wheels. I had difficulty pivoting the arms they were binding so badly. With the polyurethane installed the suspension works again. The ride is a bit harsher over bad bumps, yet smoother on minor bumps and road imperfections than before. Overall I am happy,I just hope they last another 15 years!! |
 | Rear Sway Bar Endlink Bushings - Part Number: 7401 Customer: Gary G. Rating: 5 out of 5Overall Opinion: Very Good These sway bar endlink bushings fit good. I have a 20 ton shop press. So they went in easy. I lubed them liberally with marine grease and pressed them into the bar and bracket. You do have to remove the old OEM sleeves. |
 | Motor Mount - Type A Short - Part Number: 7504 Customer: Edward Williams Rating: 5 out of 5Overall Opinion: thumbs up Thanks to these motor mounts my headers went in just fine. I tried 3 other manufacturer's mounts and each one was a problem, mainly to high causing the headers to hit the steering. |
 | Early GM Mount - Part Number: 7509 Customer: Steph Cote Rating: 5 out of 5Overall Opinion: great Outstanding construction, can't wait to install. |
 | Front Torque Strut Insert Kit - Part Number: 7510 Customer: Kristie Kaik Rating: 5 out of 5Overall Opinion: Solid, great performance This was my first time changing out engine mounts and the very first time that I put performance parts in a vehicle that I owned. My 1999 Saturn SL1 had the typical bad upper engine mount which needed to be changed. Seeing as how all the mounts should be changed at the same time, I went with OEM upper engine and transmission mounts and decided to go with the Prothane inserts for the torque mounts (commonly referred to as the "dogbones"). My lower dogbone was in decent shape yet but the upper one was really shot! Removing the rubber from the old dogbones was easy. The small end easily pushed out with a vise, socket, and a strategically placed block of wood. For the large end, I cut the webbing out of the first one as per the instructions. However, on the second one, I simply bent the tabs back and chiseled the sides in a bit and it slid out by hammer and chiseling the top to push it out. (Cutting the webbing was by far the worst step.) At first it appeared that the large inserts were too big to go in. But using a bit of dielectric grease, I worked in the tapered end by hand until it wouldn't go in any further. Then I placed it in the vise and slowly pressed it in the rest of the way. If you have the parts lined up well, it will eventually just pop right in! Make sure you press the part in without the metal bushing in place, so that the insert can compress enough to be inserted. First drive with the new inserts was great! The poly inserts gave me a little more vibration in the car but I knew that was going to happen. I feel it more in my seat than I do in the steering wheel or pedals. Its enough that the change is noticeable but its not enough to make my butt go numb. (Vibration is transferred to the "frame" which I am OK with.) However, the performance is AWESOME! My engine no longer feels like its twisting all over the place when I give it some gas. The car feels much more solid while driving. I can't say for sure that its giving me better performance as I have no way to measure that, but the feel improved and that gives me more confidence in my ride. That in and of itself is worth a lot! With all the mounts changed, my engine even sounded a little throatier, which is pretty impressive for that little SOHC! I definitely recommend these inserts with the side note of slightly increased vibration in the car frame. |
| Front Torque Strut Insert Kit - Part Number: 7510 Customer: mark Rating: 5 out of 5Overall Opinion: definately worth it I think there are two reasons someone would look here: 1 -performance upgrade, poly vs. floppy rubber. OK you dont even need to look here then... 2 -you want inexpensive replacement parts. long story short, they work great. The only time I notice any additional vibration at all is with the car in drive, stopped, at idle, and then its barely noticeable. It is more noticeable under the same conditions but with the ac on. For the money, I'll definitely take it These were $30! What I feel was the next best option: oem parts from online discounters selling for 90 a piece / 180 pair, that's before shipping. I installed all 4 mounts at the same time, (oem for the mount by the valve cover and trans) so its hard to say how much of the handling improvements came from which parts for sure, or how these compare to new oem torque struts for certain, but the car handles noticeably better than before. |
| Front Torque Strut Insert Kit - Part Number: 7510 Customer: Josh Martin Rating: 5 out of 5Overall Opinion: I found them quite useful, although it required some cutting and time to modify them to my application. Once in, they are performing great the motor sits still and steady. |
| Front Torque Strut Insert Kit - Part Number: 7510 Customer: Landon Solomon Rating: 5 out of 5Overall Opinion: Parts were of high quality... These parts are very nice right from the package. However, they did not fit my vehicle. Apparently there are two versions of the torque strut that are used on Saturns and I have the version that is unusual. After modification of the oval bushing and the torque strut I was able to install the parts and they seem to work wonderfully, limiting engine movement to a degree not previously possible. |
 | Upper Engine Mount Insert - Part Number: 7513 Customer: Cory Van Santen Rating: 5 out of 5Overall Opinion: great product Great product |
| Upper Engine Mount Insert - Part Number: 7513 Customer: luis guadalupe Rating: 5 out of 5Overall Opinion: Yes, worked great, easy to install. Thanks |
| Upper Engine Mount Insert - Part Number: 7513 Customer: Jonathon W Custer Rating: 5 out of 5Overall Opinion: pretty good The insert really stiffened up the prone to failing top motor mount on my cavalier, I will def. be back to order more from energy suspension. |
| Upper Engine Mount Insert - Part Number: 7513 Customer: David Puerner Rating: 5 out of 5Overall Opinion: a very good product for the price I have installed the engine mount insert. I am pleased with it. I look forward to purchasing the trans mounts and control arm bushings when I can afford them. My only criticism was the ebay listing pictured all three mounts and I though that was what I was buying, but still a very good product for the price. In a side note, I am a member of the Cavalier Forum, j-body.org, and they have voiced an interest in a set a rear control arm bushings. You may want to get in touch with the forum moderator, and discuss the interest level and potential market for even a limited production run. |
| Upper Engine Mount Insert - Part Number: 7513 Customer: Michel Rating: 5 out of 5Overall Opinion: very good part. Good part to stiffen up your motor mount. Since I have a bigger engine in, this part really help to "save" your engine mount. |
| Upper Engine Mount Insert - Part Number: 7513 Customer: Jeffrey Augugliaro Rating: 4 out of 5Overall Opinion: Nice look and feel to part itself Very pleased with the ease of installation. It really tightened up the engines back and forth motion. It feels sooo much tighter than with just the stock motor mounts, no more banging back and forth. Only drawback it that it made engine vibration more noticeable. |
| Upper Engine Mount Insert - Part Number: 7513 Customer: victor green Rating: 5 out of 5Overall Opinion: The part fit very good and replace the expensive motor mount of my car. Thanks you |
| Upper Engine Mount Insert - Part Number: 7513 Customer: Doug Wiesen Rating: 5 out of 5Overall Opinion: great Use plenty of WD-40 and this baby slips right in. |
| Upper Engine Mount Insert - Part Number: 7513 Customer: Victor Alfonso Hurtado Rating: 5 out of 5Overall Opinion: Great Product and Staff! This Company knows their products well! Product fit like a glove and provided the support to get the car back on the road. Great Staff and fast customer service! |
 | Front Transmission Mount Insert Kit - Manual Transmission - Part Number: 7514 Customer: Cory Van Santen Rating: 5 out of 5Overall Opinion: great product Significantly improved shifting. |
 | Rear Transmission Mount Insert Kit - Manual Transmission - Part Number: 7515 Customer: Cory Van Santen Rating: 5 out of 5Overall Opinion: great product Significantly improved shifting. |
 | Front or Rear Transmission Mount Insert - 2.2 or 2.4 Engine - Part Number: 7517 Customer: Lemuel Outlaw Rating: 5 out of 5Overall Opinion: dislike I purchased this part for a 2007 Chevy cobalt 2.2L and use it to replace the front trans mount but the idle was rough with this insert. It appears the rubber was too hard. I put in OEM replacement which has softer rubber and my idle was restored to manufacturer specifications. |
 | LS-1 Motor Mount Adapter Kit - Type A - Part Number: 7519 Customer: Raymond skaar Rating: 5 out of 5Overall Opinion: Product fit very well, and it seems that the hardness of the engine mount has a very good consistency. Not too soft and not too hard resulting in low noise in the car but the engine is very stable and fine. |
 | Front Frame Shackle Bushings - Part Number: 7801 Customer: mitchell stanley Rating: 4 out of 5Overall Opinion: decent stuff Directions for 1 tons could be better about the steering arm block |
 | Rear Frame Shackle Bushings - 1-1/2 Inch - Part Number: 7803 Customer: Brian Bayliss Rating: 5 out of 5Overall Opinion: Excellent products, shipped fast. Not rocket science. Just good parts for the price. |
| Rear Frame Shackle Bushings - 1-1/2 Inch - Part Number: 7803 Customer: Leon Arnold Rating: 5 out of 5Overall Opinion: good this kit installed easily and fit well. |
| Rear Frame Shackle Bushings - 1-1/2 Inch - Part Number: 7803 Customer: Theodore Joseph Lang Rating: 5 out of 5Overall Opinion: Professional As a consumer of many off-road and performance products I found a very professional and prompt service. I was informed at every step of my order, not to mention they where the only company who had this specific part. I fully intend on doing business with you again, Thanks. Jackal Off-road |
| Rear Frame Shackle Bushings - 1-1/2 Inch - Part Number: 7803 Customer: TJ Lang Jackal-Off road LLC Rating: 5 out of 5Overall Opinion: Very fast shipping and quality product. This is my second order from ESP and find that they are a pleasure to do business with. The bushings I have ordered have held up to the off road punishment that I look for in a quality product. I look forward to doing continued business with ESP. Thank you. T.J. Lang at Jackal-Offroad.com |
 | Rear Frame Shackle Bushing Kit - 1 3/4 Inch - Part Number: 7804 Customer: THUANBAO TRAN Rating: 5 out of 5Overall Opinion: good service fast shipping and accurate part as what I ordered, I would recommend anyone I know to get parts from your guys, and I will also get any parts I needed in the future from you also. |
 | Rear Frame Shackle Bushings - 1-3/8 Inch - Part Number: 7805 Customer: James Sandoe Rating: 5 out of 5Overall Opinion: Fast and courteous service. I am building my own triangulated 4 link in a Rat Rod. I am putting a narrowed 9 inch Ford into a custom application. I bought the first set to see if they would fit into the round tubing that I had. The fit was so tight that I had to grind on the tubing and the bushings. I am certain that the bushings will do exactly as I want. Great customer service. Thanks for the PayPal option. |
| Rear Frame Shackle Bushings - 1-3/8 Inch - Part Number: 7805 Customer: Albert Miller Rating: 5 out of 5Overall Opinion: The bushings I ordered were for a project on a 61 Ford Falcon. Although they were not for that application, they did work perfectly with a little modification. Thanks Again. |
 | Rear Frame Shackle Bushings - 1.5 OD - Part Number: 7807 Customer: Brandon Girardi Rating: 5 out of 5Overall Opinion: Fantastic They worked great for my traction bar project, an excellent value and a perfect fit for my application. Shipping was incredibly fast, thank you energy suspension parts! |
 | Front Sway Bar Bushings and End Links - 21mm - Part Number: 81101 Customer: Alex S. Rating: 5 out of 5Overall Opinion: Perfect fit for my OEM stock front sway bar. Had to modify the stabilizer bushings by grinding them a little and did not use the long bolt with my front stock sway bar. Everything else but the long bolts were utilized. Near perfect fit otherwise and my ride does not make any more noise! |
 | Front Sway Bar Bushings and Endlinks - 16mm - Part Number: 81105 Customer: Dar Dehmler Rating: 5 out of 5Overall Opinion: I can't say much. I had installed many new parts, without significant handling changes. However, these prothane sway bar bushings gave me a new car! |
 | Front Sway Bar Bushings - 19mm - Part Number: 81107 Customer: Don Collett Rating: 5 out of 5Overall Opinion: good fitting parts Parts fit really good, company support was excellent |
 | Rear Sway Bar Bushings - 15mm - Part Number: 81108 Customer: Dane D Gustafson Rating: 3 out of 5Overall Opinion: Material Good, Geometry Bad The material of these bushings is of good quality, with no defects or dryness. However, the 12 oclock position on the bushings is NOT thick enough and will not work with stock mounting brackets. You will need sheet metal to fabricate your own brackets for this installation. I was not able to install these bushings. |
 | Front Sway Bar Bushings - 22mm - Part Number: 81109 Customer: philip burdock Rating: 5 out of 5Overall Opinion: great product Great product easy to fit, great addition to my race car . |
| Front Sway Bar Bushings - 22mm - Part Number: 81109 Customer: RUBEN J BARBA Rating: 5 out of 5Overall Opinion: Give them a 10 This are good quality bushings for the price, just make sure they fit your sway bar the bushing bracket will have the size of the bushing, also use all the lube to keep them from squeaking, had mine for almost a year now with no problems. |
| Front Sway Bar Bushings - 24mm - Part Number: 81110 Customer: Steph Cote Rating: 5 out of 5Overall Opinion: great. Nice part |
 | Front Sway Bar Bushings - 22mm - Part Number: 81123 Customer: Scott Rumsey Rating: 5 out of 5Overall Opinion: nice piece Well made, easy install on existing sway bar. |
| Front Sway Bar Bushings - 22mm - Part Number: 81123 Customer: Dillon Mitchell Rating: 5 out of 5Overall Opinion: Fits perfectly. |
 | Rear Sway Bar Bushings - 13mm - Part Number: 81124 Customer: Scott Rumsey Rating: 5 out of 5Overall Opinion: exactly what I wanted Super easy to install. Attractive red.. |
 | Front Sway Bar Bushings - 26mm - Part Number: 81125 Customer: Aaron Montell Rating: 5 out of 5Overall Opinion: Great! Fits perfect and works great!! |
 | Front Sway Bar Bushings - 26.5mm - Part Number: 81127 Customer: justin broveak Rating: 5 out of 5Overall Opinion: great improvment 98 Honda accord, awesome improvement from stock. I take corners faster now. I'm sure tires are in my future! ha |
| Front Sway Bar Bushings - 26.5mm - Part Number: 81127 Customer: Mathieu Goupil Rating: 5 out of 5Overall Opinion: Very good product, comes with high quality grease! |
 | Front Strut Rod Bushings - Part Number: 81202 Customer: Charles Wardlow jr Rating: 5 out of 5Overall Opinion: Perfect for my car... The bushings were the greatest for my car thanks. |
| Front Strut Rod Bushings - Part Number: 81202 Customer: Richard S. Harris Rating: 5 out of 5Overall Opinion: The installation of these bushings was very much a simple remove and replace deal. The difference they made after installation was impressive given that my original bushings didn't "look" bad. My "mushy" feeling in the front of my car on aggressive cornering is pretty much gone. |
| Front Strut Rod Bushings - Part Number: 81202 Customer: Julian Penton Rating: 5 out of 5Overall Opinion: great I think these have the biggest effect. Tightens your steering response right up and almost eliminated wheel hop |
 | Front Strut Rod Bushings - Part Number: 81203 Customer: Marcos Pardo Rating: 5 out of 5Overall Opinion: Good Product for a reasonable price... 5 stars I bought these for my 91 Integra GS and they work just as good or even better than the OEM ones.... I would recommend these to anybody who needs to replace your worn out ones... |
 | Shifter Stabilizer Bushings - B Series Engines - Part Number: 81601 Customer: Alex Tornel Rating: 5 out of 5Overall Opinion: Works a lot better than stock ones. Not hard to install very easy. |
| Shifter Stabilizer Bushings - B Series Engines - Part Number: 81601 Customer: Ilias Konstantouros Rating: 5 out of 5Overall Opinion: Amazing Product They are absolutely amazing, I removed the oem bushings and they felt like cheap rubber. The prothane ones are very stiff and nearly impossible to bend. In driving they feel very sharp and give you more confidence. Definitely a must upgrade. Thank you PROTHANE! |
 | Shifter Stabilizer Bushings - D Series Engines - Part Number: 81602 Customer: Allen king Rating: 4 out of 5Overall Opinion: Great quality. Both of the bushings fit very well. Although one was a little off on fitment, it wouldn't have really affected its purpose much. I appreciate the small package of line to help install the bushings, it made installing them much easier. |
 | Motor Mount Inserts - 3 Mount Combo - Part Number: 81902 Customer: Steph Cote Rating: 2 out of 5Overall Opinion: low The mounts are WAY too hard. This caused and excessive amount of droning in the vehicle and caused everything else to vibrate heavily. A softer Urethane would be better in my opinion. |
| Motor Mount Inserts - 3 Mount Combo - Part Number: 81902 Customer: David Wehrheim Rating: 5 out of 5Overall Opinion: A+ deal Super stiff. Same or better then full aftermarket mounts! Just use a little lube to get them in and they are solid! A little vibration, but its a turbo civic, what do you expect, lol. |
 | Motor Mount Inserts - 3 Mount Combo - Part Number: 81905 Customer: BRANDON SMITH Rating: 5 out of 5Overall Opinion: AWESOME! I ordered these for my brothers DA Integra. It's running a pretty stout b16 swap, with a very strong 6 puck competition clutch. After a lot of power shifting, and "dash banging," we had destroyed both of the top motor mounts. We were a little skeptical about these inserts because we didn't know how well they would work inside of a broken mount.... Let me just say that these worked out GREAT! Not only were we able to salvage the shredded mounts, adding these was also a major upgrade. Yes, they will make your car vibrate a bit, but it's not horrible, and it's worth the firm throttle response you gain, and also the reduction of wheel hop. We were glad we got these instead of trying to hunt down some OEM replacements, or shelling out major cash for aftermarket mounts. |
 | Motor Mount Inserts - 3 Mount Combo - Part Number: 81906 Customer: kyle zabala Rating: 5 out of 5Overall Opinion: great product! This is awesome for someone on a budget, rather then spending $300 on full mount kits. I am very happy with it and how easy it was to install. |
 | Motor Mount Inserts - Front and Rear - Part Number: 81907 Customer: Bob Smith Rating: 5 out of 5Overall Opinion: Great Fitment & Great Product The fitment was snug and really stiffened up the mounts. The mount was torn and a replacement stock mount and an insert was a low cost solution to excessive motor movement when letting out the clutch. A complete poly mount would have been the best choice but if cost is a factor, this is not as stiff but still a good solution. Installation of the front mount was easy and quick but the rear was quite hard and time consuming. Great product! |
 | Total Kit - Part Number: 82003 Customer: kenny patacconi silvestrini Rating: 5 out of 5Overall Opinion: great item for honda lovers I recommend this item if you want to rebuild a del sol. It is not so expensive and it contains everything U need to do the job. |
 | Total Kit - with Front and Rear Upper Control Arm Bushings - Part Number: 82008 Customer: Steph Cote Rating: 5 out of 5Overall Opinion: Very good I have installed urethane kits before. This is my first from Prothane. Far superior product then other manufacturers out there. |
 | Total Kit - with Rear Upper Control Arm Bushings - Part Number: 82014 Customer: Joe Spillers Rating: 5 out of 5Overall Opinion: Great product. This product is great. A must have for a car with Hydraulic suspension. It allows free movement of the suspension without binding and destroying the suspension bushings. But the Front Sway Bar Bushings are too small. This kit comes with 25 mm Bushings, but my Front Sway Bar measures 27 mm. Also this kit doesn't include Rear Lower Shock Bushings. Just use lots of specially formulated polyurethane bushing lubricant. I recommend getting the large Tub of lubricant. |
 | Total Kit - Part Number: 82017 Customer: Arthur Esmanskiy Rating: 5 out of 5Overall Opinion: For racing use only!! Very very good quality!!! |
 | Total Kit - Part Number: 82019 Customer: vaughn dean Rating: 5 out of 5Overall Opinion: good kit Good kit still a pain in the ass getting the old or factory bushings out. Did the rear ones first. Everything fits well, no binding, good suspension travel |
 | Total Kit - Part Number: 82020 Customer: Duane Kerr Rating: 4 out of 5Overall Opinion: Good parts I installed these on a 2006 HONDA Civic Ex. These bushing are much better than the stock one. Though Honda does not make it easy to remove theirs. Once I figured out which parts went where they fit great. I would recommend a press to simplify the installation of the bushings. The only problem I had was that the rear sway bar bushings did not fit into the stock holders. For me that was not a problem. I was looking for the suspension pieces. Over all very pleased with the installation and the function of the parts. |
 | Front Upper and Lower Control Arm Bushings - Part Number: 8203 Customer: Elliott Charles Miller Rating: 5 out of 5Overall Opinion: Great but the installation had a snag. While the LCA bushings fit snuggly , it was nice that the ES bushings had more material. I think these will perform better! |
| Front Upper and Lower Control Arm Bushings - Part Number: 8203 Customer: Michael Irizarry Rating: 5 out of 5Overall Opinion: All I can say is that these parts were a great investment, after installation I noticed a huge difference immediately. I give the parts a two thumbs up and recommend it to any Honda owner who is looking for better handling and a smoother ride |
 | Front Control Arm Bushings - Part Number: 8205 Customer: reggie j. mcneill Rating: 5 out of 5Overall Opinion: great!! Exact fit!! By far the best! Parts ordered online sometimes are the wrong parts, but you guys were right on point with the parts. Everything I needed came with product |
| Front Control Arm Bushings - Part Number: 8205 Customer: Justin Bekker Rating: 5 out of 5Overall Opinion: Good quality I installed these on an 89 prelude at all four ucas and therefore I didn't need the lowers, so it would be nice if I could have bought just the uppers. They're a little squeaky, but that is to be expected with poly. The best value replacement for prelude uppers |
 | Front Lower Control Arm Bushings - Part Number: 8210 Customer: Casey Crook Rating: 5 out of 5Overall Opinion: The Best Price, quality, and customer service come together to make for one of the best retail experiences. Thank you Graham Slaughter! |
| Front Lower Control Arm Bushings - Part Number: 8210 Customer: Todd Christlieb Rating: 5 out of 5Overall Opinion: Good deal for a great product. I was the old bushings came out as easy as the new ones went in. Took a couple hours and an air chisel to remove the originals for 88. But the new ones pressed right in and a riding smooth/tight. |
 | Front Lower Control Arm Bushings - Part Number: 8212 Customer: Ryan Rating: 5 out of 5Overall Opinion: Good The parts were exactly what I needed. They were very easy to install and perform admirably. Of course with other problems present on the vehicle, it's difficult to judge overall performance difference. :) |
 | Front Upper Control Arm Bushings - Part Number: 8213 Customer: Logan Rating: 5 out of 5Overall Opinion: Good Parts If you're just looking for good reliable parts with an easy install, this is your ticket. |
| Front Upper Control Arm Bushings - Part Number: 8213 Customer: mark e forguson Rating: 2 out of 5Overall Opinion: very good I purchased these bushing for an 89 prelude upper control arm bushing. The aftermarket REFUSES to provide the correct bushing. So I had to re-machine them to correctly fit. The basic profile is correct however several "adjustments had to be made for correct installation. These bushings work excellent but it took several hours of work to re engineer them to work. This modification should only be done by a professional mechanic who understands suspension geometry. Otherwise dangerous conditions could exist if the bushings are not properly retained. |
| Front Upper Control Arm Bushings - Part Number: 8213 Customer: Fred Rating: 5 out of 5Overall Opinion: worked great I used these bushing for the rear upper control arm bushing on a 89 Honda prelude, they fit perfectly. |
 | Front Lower Control Arm Bushings - Part Number: 8215 Customer: R. lopez Rating: 3 out of 5Overall Opinion: not too bad Well, we installed these for one of our customers. I have always been impressed at the quality of these parts. Only thing we had an issue with was with fitting them back in. Once inserted into the lower control arm they took forever to get back into place......an once done we noticed that the front ones (which were for civic and not the rsx) seemed as if they wanted to pop out. We have since checked our customers suspension and still looks the same. We made sure that everything was facing towards the proper points yet not sure why they look as if they want to come out of the arm. Overall though customer is satisfied with setup, just wish there was a way to make these easier to install back into the vehicle some some kind of holder for top/bottom or around the area they fit into on the control arm. |
| Front Lower Control Arm Bushings - Part Number: 8215 Customer: Chris Hunter Rating: 4 out of 5Overall Opinion: PITA to install, had to machine a custom tool and use a large hydraulic press. Only installed the large vertical bushings because it was easier and the original were destroyed. |
 | Front Lower Control Arm Bushings - Part Number: 8216 Customer: Charles Wardlow jr Rating: 5 out of 5Overall Opinion: I loveem the feel of my honda is so much better now with the bushing that you provided me. The ride that I now feel is way better that factory thanks again. |
 | Rear Trailing Arm Bushings - Includes Hardware - Part Number: 8304 Customer: teva tautu Rating: 5 out of 5Overall Opinion: Nice part !!! Amazing part, my car feels more stable than with the oem one. No squeaking or anything, this is a good stuff !!! |
| Rear Trailing Arm Bushings - Includes Hardware - Part Number: 8304 Customer: Fong Xiong Rating: 5 out of 5Overall Opinion: Super Impressed Old trailing arm bushings were torn and I knew these were the product I was going to buy. Cornering and handling greatly improved. |
| Rear Trailing Arm Bushings - Includes Hardware - Part Number: 8304 Customer: Raley Rating: 4 out of 5Overall Opinion: Does its job. Got the black kit since its impregnated with graphite (helps with the squeaks) The directions for these was pretty good actually, way better then any ES product I've seen. |
| Rear Trailing Arm Bushings - Includes Hardware - Part Number: 8304 Customer: Z.V. Rating: 5 out of 5Overall Opinion: Satisfied. All i can say is flawless...WAYYYYY better than the OEM trailer bushing. Better handling on turns and soften the blow when I go over bumpy roads. |
 | Rear Control Arm Bushings - Upper and Lower - Part Number: 8306 Customer: Taylor Rating: 5 out of 5Overall Opinion: great product, easy install This is a great product and really tightened up my suspension and improved the feel of the car. Definitely recommended if you are in the market to refresh your ride, beware though that they do not fit with Blox LCAs where the shock body meets the LCA, but work with my new Skunk2 LCAs and OEM with no issues. |
| Rear Control Arm Bushings - Upper and Lower - Part Number: 8306 Customer: Daniel Estrada Rating: 5 out of 5Overall Opinion: Very comfortable!! I'm glad with purchase!! Only a little grind!! It's been a month since I put them on |
| Rear Control Arm Bushings - Upper and Lower - Part Number: 8306 Customer: Dominique BEGUE Rating: 5 out of 5Overall Opinion: Hi, Nice item, they are just "plug and play". Perfect for rebuilding old cars or not. Very good quality. Thanks |
| Rear Control Arm Bushings - Upper and Lower - Part Number: 8306 Customer: Christian A MARTINEZ Rating: 5 out of 5Overall Opinion: awesome product These bushings are fantastic - my car rides better than ever. It is also a bonus that these parts disassemble, which makes installing much easier than the stock/factory bushings. Ive already recommended these bushings to others. |
 | Rear Upper Control Arm Bushings - Part Number: 8307 Customer: Customindz.de Rating: 5 out of 5Overall Opinion: Very good The parts fit perfectly and are easy to install. The quality is very good. I have these installed on a different car and have been driving them now for 3 year. They still look like they are new and the metal also still looks very good. No rust no nothing! These are perfect to complete the master kit for your Honda. Driving all this together is just perfect. You get so much feeling of The street and the car. The rear axle gets stiffer and the movement of the axle in corners is way less. Plus they are cheap compared to thepy rubber ones and hold much longer! |
| Rear Upper Control Arm Bushings - Part Number: 8307 Customer: Don Collett Rating: 5 out of 5Overall Opinion: excellent parts Parts were easy to install. Made the car handle much better. Company help and support was very good |
| Rear Upper Control Arm Bushings - Part Number: 8307 Customer: impressed buyer Rating: 5 out of 5Overall Opinion: I did all the suspension bushings in the car and the the difference is very impressive. |
| Rear Upper Control Arm Bushings - Part Number: 8307 Customer: Matthew D Little II Rating: 5 out of 5Overall Opinion: Excellent Quality. These bushings were great, easy to install, and made a huge difference in the handling in my car. |
| Rear Upper Control Arm Bushings - Part Number: 8307 Customer: Christian Jacot Rating: 5 out of 5Overall Opinion: Very good Fits well in place, easy installation, no problems so far. |
 | Rear Lower Control Arm Bushings - Part Number: 8308 Customer: Jesse Alt Rating: 5 out of 5Overall Opinion: Exactly as ordered. No complaints Installed as expected and have had no problems. |
| Rear Lower Control Arm Bushings - Part Number: 8308 Customer: shahin shahbaz zadegan Rating: 5 out of 5Overall Opinion: Just the best tnx all |
| Rear Lower Control Arm Bushings - Part Number: 8308 Customer: Andy Viertel Rating: 5 out of 5Overall Opinion: very nice car-parts This Parts are very good processed and easy in assembling. |
 | Rear Compensator Arm Bushings - Part Number: 8309 Customer: Dominique BEGUE Rating: 5 out of 5Overall Opinion: Easy to install, nice item compared to the old one. No problems. |
| Rear Compensator Arm Bushings - Part Number: 8309 Customer: John Carmichael Rating: 5 out of 5Overall Opinion: Have not installed yet, but look well built Well packaged, well built. Should be include with the master kit. |
| Rear Compensator Arm Bushings - Part Number: 8309 Customer: impressed buyer Rating: 5 out of 5Overall Opinion: You might as well complete your suspension with these. |
| Rear Compensator Arm Bushings - Part Number: 8309 Customer: Customindz.de Rating: 5 out of 5Overall Opinion: Very good The parts fit perfectly and are easy to install. The quality is very good. I have these installed on a different car and have been driving them now for 3 year. They still look like they are new and the metal also still looks very good. No rust no nothing! These are perfect to complete the master kit for your Honda. driving all this together is just perfect. You get so much feeling of The street and the car. The handling is much more precise and the car feels way better to drive. Plus they are cheap compared to thepy rubber ones and hold much longer! |
| Rear Compensator Arm Bushings - Part Number: 8309 Customer: Christian Jacot Rating: 5 out of 5Overall Opinion: Very good Fits well in place, easy installation, no problems so far. |
| Rear Compensator Arm Bushings - Part Number: 8309 Customer: Mike Royer Rating: 5 out of 5Overall Opinion: very good Fast delivery and the part was an exact replacement. Good fit. |
| Rear Compensator Arm Bushings - Part Number: 8309 Customer: Matthew D Little II Rating: 5 out of 5Overall Opinion: Grade A+ Superb Quality. These bushings were excellent, easy to install, and made a HUGE difference. Energy Suspension is definitely the way to go for anything suspension related. |
| Rear Compensator Arm Bushings - Part Number: 8309 Customer: Thibaut DEGREMONT Rating: 5 out of 5Overall Opinion: the chassis is efficient It takes a few time to install the complete kit with no professional tools but the chassis is more efficient ! We'll see with the timeif they will be as reliable as now |
| Rear Compensator Arm Bushings - Part Number: 8309 Customer: ryan defillipi Rating: 5 out of 5Overall Opinion: Very Pleased Good Quality, fit perfectly, no problems! |
| Rear Compensator Arm Bushings - Part Number: 8309 Customer: mathieu daoust Rating: 5 out of 5Overall Opinion: perfect fit! Nice part, fits well! |
 | Rear Lower Control Arm Bushings - Part Number: 8312 Customer: Alex Polinskiy Rating: 5 out of 5Overall Opinion: Great quality, easy to install Great quality, easy to install |
 | Rear Control Arm Bushings - Upper and Lower - Part Number: 8313 Customer: Brian May Rating: 5 out of 5Overall Opinion: good Work great - needs 3 packets grease included, currently comes with 2. Instructions suck though. 90-93 accord upper ctrl arm is thin stamped steel and is easy to bend unless you space it while pressing out bushing. |
| Rear Control Arm Bushings - Upper and Lower - Part Number: 8313 Customer: Charbonnel Fabien Rating: 5 out of 5Overall Opinion: French customer. These parts can be mounted on EURO ACCORD 93-98 model type: CC7. Very good parts. Easy to install. |
 | Rear Trailing Arm Bushings - Integra 1990 - 1993 - Part Number: 8314 Customer: Jason Radke Rating: 4 out of 5Overall Opinion: These worked better than the oem I did a 1990 integra rear disk swap in my 90 civic and wanted to replace the old worn out bushings. These worked better than the oem parts and will last longer down the road too |
| Rear Trailing Arm Bushings - Integra 1990 - 1993 - Part Number: 8314 Customer: PATRCIK JOCELYN Rating: 5 out of 5Overall Opinion: nice and sturdy Out of all the stubborn bushings I had to replace, I had the most fun replacing the trailing arm bushings. The best part about installing these bushings is that I didn't have to clock them when installing. |
| Rear Trailing Arm Bushings - Integra 1990 - 1993 - Part Number: 8314 Customer: Nicholas patrick kern Rating: 5 out of 5Overall Opinion: Very very satisfied! PROTHANE is the only way to go in any bushing setup! They were very easy to install! The instructions were very easy to understand and read. Well worth the price!!! |
 | Rear Lower Control Arm Bushings - Type R Only - Part Number: 8317 Customer: hong Rating: 5 out of 5Overall Opinion: Awsome!!!! Well i looked every where for better bushings for my Integra type r and these where the only ones I found. I guess these where the only ones because they were so darn good you really didn't need anything else :)... after the install I noticed my back was more planted and followed through the turns on the track much better. Having more CONTROL over steer in a FWD is always a plus. |
 | Rear Upper and Lower Control Arm Bushings - Part Number: 8318 Customer: Ramesses Bruce Rating: 5 out of 5Overall Opinion: great product Parts were easy to install. Correct fitment ....now the car has a nice sturdy feel no more sloppy suspension. |
 | Front Sway Bar End Links - Part Number: 8401 Customer: RUBEN J BARBA Rating: 5 out of 5Overall Opinion: works great Great fit and quality, definitely stiffer than stock, had this for almost a year now with no problems. |
| Front Sway Bar End Links - Part Number: 8401 Customer: Scott Rumsey Rating: 5 out of 5Overall Opinion: well made part..nice finish. Parts easy to install, should perform much better than old deformed oem bushings... |
| Front Sway Bar End Links - Part Number: 8401 Customer: Jason Yang Rating: 5 out of 5Overall Opinion: GREAT! Perfect fitment, awesome product for an awesome price! |
| Front Sway Bar End Links - Part Number: 8401 Customer: Carlos Oyola Rating: 5 out of 5Overall Opinion: It's a good part, easy to install, and gives a great stiffness mated with the other suspension components. |
| Front Sway Bar End Links - Part Number: 8401 Customer: Todd Christlieb Rating: 5 out of 5Overall Opinion: Good deal for a grate product My old links were dry rotted and worn to nothing. After replacing these and every other suspension part with new poly ones my accord is tight as a brand new 88 accord. lol |
 | Front Sway Bar Endlink Bushings - Part Number: 8404 Customer: Matthew Kullman Rating: 5 out of 5Overall Opinion: easy to install. works great easy to install. works great |
 | Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: Matt Rating: 5 out of 5Overall Opinion: Completely satisfied give me all that I was searching for. Owned and installed-2 months or so.i am very pleased with how solid and planted my car feels and performs I can now drop gears when merging or changing lanes to keep with flow of traffic without worrying about is my drivetrain going to keep up with my expectations great product through and through hands down . I did not install the t-bracket insert . Yes it transfers vibrations into the car and your car car may soon have rattles I expected that since my car is a 94 IMO (in my opinion) you get used to it with some fiber cloth stuffed here and there.i didn't want solid mounts because if your motor mounts are not giving even just a little something else will .axles, transmission other drivetrain parts ect. Best Bang For Your Buck |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: Robert Bonning Rating: 5 out of 5Overall Opinion: very great parts! These were easy to install and tightened everything up so now more power goes to the wheels, I would definitely recommend to others |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: Gilles TRICARD Rating: 5 out of 5Overall Opinion: very good product at very good price , higly recommended Very good product at very good price, highly recommended, easy installation. |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: Ryan Russell Rating: 5 out of 5Overall Opinion: The top one side is hard to get the motor mount apart but once you do, it goes right back together. A good part for the price thanks again. |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: luis irizarry Rating: 5 out of 5Overall Opinion: Great buy Nice and stiff, easy installation, great help when it comes down to putting down horsepower to the wheels as fast as possible. |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: Andy Tran Rating: 5 out of 5Overall Opinion: Awesome Exactly what I expected, I don't have any complaints about them. They work awesome! |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: Suvit Tongkul Rating: 5 out of 5Overall Opinion: Easy to install. |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: olivier regnault Rating: 5 out of 5Overall Opinion: Very good parts |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: layre Rating: 5 out of 5Overall Opinion: uper mounts a great additon to any car i love these mounts i opted for the race version but these mounts are great i would buy them over hasport anyday you do get increased vibration but its not something you cant deal with if you like me and you want the best preformance out of any part these are a must on you wish list i have them on my integra and im going to put them on all my other cars to its a must buy |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: Kip McLaughlin Rating: 5 out of 5Overall Opinion: Great!! These worked great for me! I love how it has a street and a race insert! makes it a lot easier on the streets! Still some extra vibration, but that is to be expected! |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: Rob Barbieri Rating: 5 out of 5Overall Opinion: Installation was a breeze Had to have stock upper bushing pressed out and new one pressed in, but installation was a breeze. With inserts on all 5 mounts, the car vibrates like crazy, but its a track only car so who cares! |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: julien sauve Rating: 5 out of 5Overall Opinion: very good good |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85018502 Customer: Simao Castro Rating: 5 out of 5Overall Opinion: Very good quality item. Very good quality item, better than oem. Perfect fit. |
 | Rear Firewall Motor Mount Inserts - Part Number: 8503 Customer: Basilio Concepcion Rating: 5 out of 5Overall Opinion: Just as good as getting full polyurethane mount. It took a bit of finesse to get it in, but it was worth it. You do feel the motor better with this mount as it is on the firewall. You will get some vibration, but it is not annoying. I liked it very much,thanks again. |
| Rear Firewall Motor Mount Inserts - Part Number: 8503 Customer: Matthew Field Rating: 5 out of 5Overall Opinion: Motor mount inserts These have been amazing so far. I get a little vibration through the dash but my motor is not moving back and fourth at all and no wheel hop when I shift hard |
 | Engine Mount Inserts - Driver Side Upper - Part Number: 8504 Customer: Jonathon Wilson Rating: 5 out of 5Overall Opinion: Good quality for the price They are a good quality insert only complaint about them is the picture is red and both sets Ive ordered turned out black. Its not a huge deal just a little miss leading but overall I'm happy with them and will continue to buy them. |
| Engine Mount Inserts - Driver Side Upper - Part Number: 8504 Customer: Maksym Chernov Rating: 4 out of 5Overall Opinion: For race track ONLY! With all advantages it gives to your ride it has one bad thing - a lot of motor vibration on a body. It may be good for a race day, but not so comfortable as for a daily driven car, especially if you have passengers and trying to have a conversation while driving. |
 | Motor Mount Inserts - Set 2 of 2 - Part Number: 85048505 Customer: Jonathan A. Capulin Rating: 5 out of 5Overall Opinion: It feels alot different, but In a good way. I installed both sets of the motor mount inserts.. It feels alot different, but In a good way. I like the way it feels. The only downside is the interior of the car seems to vibrate more. I would recommend this.. CHECK YOUR STOCK MOTOR MOUNTS! theyre probably worn out! |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85048505 Customer: Ryan Rating: 5 out of 5Overall Opinion: Get firm in the right places These insets are a great compliment to the engery suspension kit. Firms your engine up nicely. My SI is even more of a pleasure to drive now. The install is straight forward maybe a 2 out of 5 on difficulty. Can't beat them for the price. |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85048505 Customer: David Robinson Rating: 5 out of 5Overall Opinion: nice They really do hold your motor in place better so when u corner throttle or brake your motor wont shift its weight as much. They do cause a lot of vibration when in idle but if you want performance then you wont care about the vibration. |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85048505 Customer: Kyle Rutledge Rating: 5 out of 5Overall Opinion: Just Great! Never knew they even made these inserts until I came to this website. I have bought the master kit from Energy Suspension awhile back, thought that kit had everything possible to stiffen my car up. This mounts will just add more stiffness along side of the other inserts I already have. Thanks. Maybe offer a kit with all the inserts as one package as well to make the buy process quicker without having two packages shipped, save on shipping, which you send the savings down to the customer, and be a win/win situation for all. Just a thought. |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85048505 Customer: bruno bezerra winge Rating: 4 out of 5Overall Opinion: Nice! Nice bang for the buck! Bushing gets really improved. Nice product for those who want improvement in engine and tranny mounts for street/strip use. A bit tricky to install, but nothing a good mechanic cant do in 20min. |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85048505 Customer: JASON GALEA Rating: 5 out of 5Overall Opinion: Very satisfied. Thanks. |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85048505 Customer: Casey Alan Cummings Rating: 3 out of 5Overall Opinion: satisfied The prothane motor mount inserts are a decent cheap way to get a stiffer grab on those gears. The mounts are very easy to install even for a novice mechanic. When adding solid mounts strong in car vibrations can occur so buyer beware. I knew this but as my car is raced and driven on the street I do not mind. |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85048505 Customer: Ereyla Galvez Rating: 5 out of 5Overall Opinion: Excelent At first I was afraid the car would vibrate too much with the hard inserts, but surprisingly it didn't. Now the car runs smother, shifting gears have become more easier at high rpms, so I highly recommend this product to all high performance enthusiast. |
| Motor Mount Inserts - Set 2 of 2 - Part Number: 85048505 Customer: Jose Martin Arias Rating: 5 out of 5Overall Opinion: Muy bien! Muy bien producto, y lo puede instalar uno mismo. |
 | Transmission Mount Inserts - Right Upper - Part Number: 8505 Customer: Tanner Hallihan Rating: 5 out of 5Overall Opinion: they work Inserts work great. Although when I received these, they were just thrown in a USPS box with NO INVOICE. The inserts were not packaged in any Prothane packaging. I'm not even sure if they are real Prothane products or just copies. The picture above shows a dull finish, the inserts I received were glossy and didn't fit correctly. Buyer beware. |
| Transmission Mount Inserts - Right Upper - Part Number: 8505 Customer: Maksym Chernov Rating: 5 out of 5Overall Opinion: Perfect! Have absolutely no complaints about this part! Since I've installed it, on my car I never had any problems with it. Doesn't give me any body vibration even on high RPM. Would recommend it for street and track use! |
 | Motor Mount Inserts - Set 2 of 2 - Honda CRX Civic 88-91 - Part Number: 85068507 Customer: Ryan Nix Rating: 3 out of 5Overall Opinion: Does not fit right in will have to file the rubber to fit. Said forget it after 30 minuets. |
| Motor Mount Inserts - Set 2 of 2 - Honda CRX Civic 88-91 - Part Number: 85068507 Customer: MOISES GONZALEZ ALARCON Rating: 5 out of 5Overall Opinion: ALL OK |
| Motor Mount Inserts - Set 2 of 2 - Honda CRX Civic 88-91 - Part Number: 85068507 Customer: Dakota Kaech Rating: 5 out of 5Overall Opinion: Great part! Helped to improve my motors stability for a much better ride. Motor mount inserts are an affordable and very useful upgrade. |
| Motor Mount Inserts - Set 2 of 2 - Honda CRX Civic 88-91 - Part Number: 85068507 Customer: Bron Stevens Rating: 5 out of 5Overall Opinion: Removed Too Stiff does not allow isolate engine vibration from chassis. |
| Motor Mount Inserts - Set 2 of 2 - Honda CRX Civic 88-91 - Part Number: 85068507 Customer: John Corso III Rating: 5 out of 5Overall Opinion: great product, great price. Very good product, easy install, great results |
| Motor Mount Inserts - Set 2 of 2 - Honda CRX Civic 88-91 - Part Number: 85068507 Customer: Jonathan Walker Rating: 1 out of 5Overall Opinion: Too noisy and harsh Installed these for two weeks and then removed them. The noise levels and body vibrations made the car undrivable. If you want to feel all the vibrations of the engine then these are for you. The vibration of the windscreen was so great that I could not use the rear view mirror. I would not recommend these for every day street use. I no longer use this item. |
| Motor Mount Inserts - Set 2 of 2 - Honda CRX Civic 88-91 - Part Number: 85068507 Customer: George Rating: 5 out of 5Overall Opinion: GREAT but Noisy interior. I bought this set with another set. Installation was straight forward. Just need a little hammering and pressing since it's a tight fit (good fit). The insert helped A LOT with my engine movement since I had worn out engine mount. The only downside is the interior is a lot noisier now (almost like sitting inside a sub box). To me I am ok with the noise since it only happens between 1000-1500rpm (sometimes idling too). |
| Motor Mount Inserts - Set 2 of 2 - Honda CRX Civic 88-91 - Part Number: 85068507 Customer: jovan norman Rating: 5 out of 5Overall Opinion: liked a lot I had extremely worn bushings and these worked perfect to fix my car. Idles low so not a lot of vibrations, so I'm a happy camper. |
 | Motor Mount Inserts - Rear Firewall Mount - Part Number: 8508 Customer: maurilio lopez Rating: 5 out of 5Overall Opinion: great loved it i put it on and it works great thanks the thing is the picture is red and i got in black but still works great again thanks. |
 | Firewall Mount Inserts - Rear - Part Number: 8509 Customer: Tanner Hallihan Rating: 5 out of 5Overall Opinion: they work Inserts work great. Although when I received these, they were just thrown in a USPS box with NO INVOICE. The inserts were not packaged in any Prothane packaging. I'm not even sure if they are real Prothane products or just copies. |
 | Driver Side Upper Motor Mount Inserts - Part Number: 8510 Customer: Z Rating: 1 out of 5Overall Opinion: =( First off, they didn't fit right when I received them so I shaved it down and it was really stiff, made the whole car vibrate worse then before. I ended up going to a junkyard and getting a motor mount that was in good shape. Save your money and time, just buy a new motor mount. |
 | Motor Mount Inserts - Rear - Part Number: 8514 Customer: Errol Yap Rating: 5 out of 5Overall Opinion: Great Value for the Money!! This part is for the serious performance/handling freak..used to eliminate rocking motion from the drive train it will introduce some noise and vibration; but this is minor compared to the performance improvements you will experience. I also have the front inserts and there is no rocking of my drive train, so all my power goes to the ground. Installation took me an afternoon to do. Make sure to support the motor and take extra precautions since you will be under the car. Money well spent; energysuspensionparts shipped my order so fast the FEDEX guy burnt his hands delivering it to my home. |
| Motor Mount Inserts - Rear - Part Number: 8514 Customer: Michael Turner Rating: 5 out of 5Overall Opinion: Amazing ! Installed on a broken mount, on a 91 Accord LX, and it works perfectly. I don't see a need to put these on a new mount as stiff as they are. I could tell a difference immediately, as it absorbed quite a bit vibration. Definitely Wanting to try the whole suspension kit! |
 | Motor Mount Inserts - Front - Part Number: 8517 Customer: George Hammond Rating: 5 out of 5Overall Opinion: Very satisfied The insert fit perfectly and made a big difference. |
 | Steering Rack Bushings - Power Steering Only - Part Number: 8702 Customer: Alex Rating: 5 out of 5Overall Opinion: Good stuff Everything fit right and it shipped faster than I'm used to. Thanks! |
| Steering Rack Bushings - Power Steering Only - Part Number: 8702 Customer: AITOR GARCIA RESA Rating: 5 out of 5Overall Opinion: Good material in the bracket to install. |
 | Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: Gary Zamuda Rating: 5 out of 5Overall Opinion: great Just had time to install them. Fit like a glove. Very happy |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: Richard Seume Rating: 5 out of 5Overall Opinion: Great Easy to install just put the washers on the bolt head side so that the bushing does not pull off in an off camber situation. Best deal for the money to replace the swaybar endlink problem that these trucks all have. R |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: Darrell Doerr Rating: 5 out of 5Overall Opinion: Very good. New bushings absolutely took care of my problem. Easy to install, quality product. Would definitely recommend them and will do business with you again when needed. Thanks, Darrell. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: John R Rumans Rating: 5 out of 5Overall Opinion: Quality parts Only hard part about installing these bushings was getting the old factory ones out. After removing the old bushings the new ones fit right in. Will recommend these to my friends. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: Shawn Bowman Rating: 4 out of 5Overall Opinion: Great fit, poor instructions. These fit well and are working great. You will need a press to get your old bushings out. The instructions supplied do absolutely nothing to help you getting these put in. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: wayne roeber Rating: 5 out of 5Overall Opinion: excellent Works as described, poly bushings press in easily. OEM bushings have outer metal shell, will require a press to remove from link. Firmed up the ride/sway and removed "clunk" noises up front. Definitely a "must do" upgrade for the "x". |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: G M McBride Rating: 4 out of 5Overall Opinion: Excellent quality Easy to install, much better than the oem. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: Dan McQuillan Rating: 5 out of 5Overall Opinion: Good! These bushing were installed on a 2000 Excursion 4x4. The only way to get the stock movable bushing out is to heat it up or use a shop press. I stress the heat part. Once the old bushing is out these are very easy to install and stiffen the ride quality. These are an inexpensive fix for worn out sway bar end links. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: scott young Rating: 5 out of 5Overall Opinion: perfect The fit is great. Fast shipping. Hardest part was getting the old bushings out. Could use some kind of instructions for the install (like which side the washers go on). Overall very satisfied. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: Josh Raczka Rating: 5 out of 5Overall Opinion: What a world of difference. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: David Jarvis III Rating: 5 out of 5Overall Opinion: Great part, great price Easy to install, could use directions. I found a video on youtube that helped. You're going to need a press at minimum. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: Lynn Ver Steeg Rating: 5 out of 5Overall Opinion: Great parts, fit perfectly. These fit perfectly, the only negative is they were sent matched up on the metal sleeve. That made it a bit of a puzzle to figure out there intended position at install. A simple diagram would have been great for us people who do not deal with suspension all of the time. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: Tim Regan Rating: 5 out of 5Overall Opinion: Acceptable These installed fine. The only thing I was unsure of was which side to put the washer on because the directions are generic. I put it on the opposite side of the sway bar and it looked right. I also drilled a hole and tapped in a grease fitting on the sway bar to inject grease into the bushing because there is a small gap between the 2 bushing pieces to allow the grease to reach the sleeve. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: Ray Schork Rating: 5 out of 5Overall Opinion: Great idea BUT I could not get the old bushings out so I just ended up not using the parts. I purchased new sway bar links. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: Steven Crosier Rating: 5 out of 5Overall Opinion: Great replacement Very easy to replace as long as you have a strong press. I used a 12 ton press and it worked a bit to get them out, but did the job. |
| Front Sway Bar Endlink Bushings - Part Number: 881166 Customer: micah downey Rating: 5 out of 5Overall Opinion: OK but not perfect I have a 2000 Ford Excursion with 285/70/18 Nitto Trail Grapplers mounted on KD Spy wheels on it. I just wanted to level the front (which I did via shackle extension)to keep the tires from rubbing. Now after installing the energy suspension sway bar end link bushings I am getting a popping noise occasionally. The Energy kit did fit pretty good. And it definitely took away the rattle I was getting from my old factory worn out sway bar end links. Installation was easy. Maybe the shackle extension is pulling the sway bars too far? |
 | Front Shock Mount Bushings - Part Number: 8903 Customer: Charles Wardlow jr Rating: 5 out of 5Overall Opinion: Perfect my car loves them. My car doesn't squeak like it used to thanks for this great product. |
 | Rear Upper and Lower Shock Bushings - Part Number: 8904 Customer: Alexey Fedoseev Rating: 5 out of 5Overall Opinion: Excellent product!!! |
 | Front Shock Mount Bushings - Part Number: 8907 Customer: Phillip Higbea Rating: 5 out of 5Overall Opinion: Excellent Easy to install. Great Price. Fast Shipping. We had a little glitch, but over all completely satisfied. |
 | Front Leaf Spring Eye and Shackle Bushings - Part Number: 91002 Customer: Huber Concepts Rating: 5 out of 5Overall Opinion: refreshing Refreshes my 50 yr old Scout. I may have purchased double order by mistake. It's OK, I'll use the bushings sooner or later. Thanks, John |
| Front Leaf Spring Eye and Shackle Bushings - Part Number: 91002 Customer: Keith Kovalchek Rating: 5 out of 5Overall Opinion: Excellent value There are very few suspension parts listings for my 67 scout 800 2wd. This bushing kit works great for the shackle ends, but are a bit too wide once installed for the frame flanges. You will have to make minor modifications to the flange, bushing or spring. This may not be true for 4WD. Once installed these are simply the best upgrade you can make to your stock saggy bushings. Also, some pictures of this kit show shiny new hardware and shackles. You are buying bushings and sleeves only. it would be really cool if a kit with bushings and hardware was offered. |
| Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 91002_rear Customer: Prentice C Emler Rating: 5 out of 5Overall Opinion: I like the quality far exceeds factory rubber parts. |
| Rear Leaf Spring Eye and Shackle Bushings Kit - Part Number: 91002_rear Customer: Timothy Sims Rating: 5 out of 5Overall Opinion: Great product With a little elbow grease the rear springs are back to better than factory. |
 | Front Frame Shackle Bushings - Part Number: 9803 Customer: Robert W Souza Rating: 5 out of 5Overall Opinion: Parts are of good quality, and fit well. |
 | Package Deal for Motor Mount Inserts - 4 Mount Set - Part Number: Prothane_PackageDeal001 Customer: Colin Rose Rating: 5 out of 5Overall Opinion: Great. This is an engine mount kit to fit an EC5W VR4. Fitment is perfect, but you need to use the original metal tube for the front roll stop instead of the supplied one which is slightly too short. Great product, very happy. |
| Package Deal for Motor Mount Inserts - 4 Mount Set - Part Number: Prothane_PackageDeal001 Customer: Nicholas Mann Rating: 5 out of 5Overall Opinion: Impressive and good value. All four engine mounts for the 8th gen Galant/Legnum VR4. I work on these a lot and often see tired mounts. Installing these is not a quick easy job, but many home enthusiasts could undertake the job and come out successfully. The engine sits where it should, and makes gear changes and direction changes noticeably better. There is slightly more vibration than OE mounts, but only noticeable when the revs drop below 800rpm. Even saying that, Id happily fit these again to another customers car. |
| Package Deal for Motor Mount Inserts - 4 Mount Set - Part Number: Prothane_PackageDeal001 Customer: Tim Devereux Rating: 5 out of 5Overall Opinion: Fitted in nice and easy - great quality product and fast delivery considering it came from overseas. Highly recommend |
| Package Deal for Motor Mount Inserts - 4 Mount Set - Part Number: Prothane_PackageDeal001 Customer: richard stanbrook Rating: 5 out of 5Overall Opinion: Perfect Perfect package for Galant VR4 8G everything fits perfectly, and makes a big difference. I could not be happier. |
| Package Deal for Motor Mount Inserts - 4 Mount Set - Part Number: Prothane_PackageDeal001 Customer: Nick Grahame Rating: 4 out of 5Overall Opinion: Really good! Excellent kit for the money - although for a good installation guide, sign up to ClubVR4! Only observation is that the steel bush in the front mount is too small, so needs to be either packed with washers, changed for the stock one, or a new one machined up. Overall excellent though. |
| Package Deal for Motor Mount Inserts - 4 Mount Set - Part Number: Prothane_PackageDeal001 Customer: Adam Turkiewicz Rating: 5 out of 5Overall Opinion: Good Just to confirm that this set is made for VR4 Galant/Legnum, great service and quick postage, thanks. |
| Package Kit - Ford F250 and F350 4WD Package Kit - Part Number: Prothane-PackageDeal053 Customer: Mark Hahn Rating: 5 out of 5Overall Opinion: very good With the limited information that I was provided, and the fact that ford has no standard for what bushings they use, the sales person Mr. Graham was great to deal with. Very helpful and professional. Thank You Mark s. Hahn | |
| Total Reviews: 1171 | |
- Order Status
- 888-406-2330
Login Status
|
| Not logged in - Login |
- Live Chat Support
- “Great work. Thank you so very much. I am very happy. ...”
- Yolgin D. - Russia. Berdsk.