Outer Tie Rod Dust Boots - Acura Integra - 191711

  • 191711 360image 1
  • 191711 Tie Rod Dust Boots
  • 191711 Tie Rod Dust Boots
  • 191711 Tie Rod Dust Boots
  • 191711 Tie Rod Dust Boots
  • 191711 Tie Rod Dust Boots
  • 191711 360image large 1

Tie Rod Dust Boots

Manufacturer: Prothane
Part Number: 191711

Color: (?)
Price: $4.17

check_box In Stock check_box Ships Immediately

  • Lifetime Warranty. Prothane guarantees all Prothane Suspension Parts to be free of defects in materials and workmanship (not due to abuse, neglect or misapplication) for the total time the vehicle remains with the original purchaser of the product(s). Should the products fail to meet these conditions, Prothane will replace the product, free of charge. This excludes any and all related labor charges. The product must be shipped to Prothane (postage prepaid) along with a copy of the original receipt."
Cross Reference from 191711 to 9.13103
Energy Suspension 9.13103
Price: $3.82
Warranty: 2 Year Warranty

FitmentTie Rod Dust Boots 191711 fits these vehicles:

Outer Tie Rod Dust Boots - Acura Integra - 191711

Pin Opening Diameter Base Opening Diameter Height of Boot Piece Number
(0.472 inch)
(1.2 inch)
(0.965 inch)
Here is our complete list of universal dust boots.

Prothane Polyurethane Universal Dust Boots

Many of you are finding out that the rubber boot on your ball joint or tie rod has rotted away or has split. These boots are extremely important for the suspension of your vehicle. Fortunately, Prothane makes Universal Dust boots that will fit most vehicles. These dust boots are made of polyurethane and are far more durable than rubber. This will seal your boot to retain the grease in the joint, as well as protecting the joint from dirt, sand, water, and snow.

Prothane Dust Boots

Prothane Dust Boots

How-to obtain measurements

In order to select the proper boot, you will first need to grab a few measurements. The best way to do this is with a set of digital calipers. You will need to measure the diameter of the base where the boot will sit, the diameter of the shaft (also called the Pin Opening Diameter) and the height of the boot. Once you have gotten to your tie rod end measure these three spots. Be sure to be as exact as possible and to write down your measurements. If you have any trouble getting these measurements, give our customer service team at DST a call.

It is important to note that you do not want to choose a boot that is bigger than your measurements. You want to choose a boot that is just slightly smaller than the measurements you obtained. The elasticity of the polyurethane will allow the hole to stretch and grip the joint tightly. If you choose a boot that is too large there will be a gap which lets in debris.

Does this boot match your needs?

Now that you have these measurements, you can verify that this is the boot that you need. If you find that your measurements do not match this boot, go to our Universal Dust Boot page to match a part to your measurements.

Prothane Dust Boots
Prothane 191711

Product Reviews for Outer Tie Rod Dust Boots - Acura Integra - 191711

5 Star (7)
4 Star (0)
3 Star (0)
2 Star (0)
1 Star (0)

Prothane 191711

5 out of 5 based on 7 user reviews. Write a Review


starstarstarstarstar" Review 2 Years Later "

These tie rod dust boots are 2 years old now and look as good and fit as well as the day I installed them.

verified_user Verified Buyer - Danny Marr - . Prothane 191711 - 5 out of 5

starstarstarstarstar" Review 2 Years Later "

Very good product.

verified_user Verified Buyer - olvin castillo - . Prothane 191711 - 5 out of 5

starstarstarstarstar" very good, great idea "

They fit well and will keep dirt and water off ball joint, however I did a little bit of a wrong measurement diameter on bottom part , my fault I know where I went wrong, I should have ordered the base 2mm bigger. It is tight but will work, over all I like the product and cost is very affordable, I will order again in the future for sure, Thank you.

verified_user Verified Buyer - robert white - . Prothane 191711 - 5 out of 5

starstarstarstarstar" Review 2 Years Later "


verified_user Verified Buyer - LU HSIN HENG - . Prothane 191711 - 5 out of 5

Fitment for 191711

compare_arrows Compare with Similar Parts

This Part
191711 compare
Energy Suspension
Energy Suspension compare
($0.35) cheaper

question_answer Customer Questions and Answers

Does part number 191711 not come with a snap ring? Does it just slip over the top of the joint?
No, part number 191711 does not come with a snap ring. Since it is polyurethane, it does not require a snap ring to stay in place. It will take a bit of force, but yes, it will slip over the joint like normal.